bemodern Pryzm Volta 42 Mode d’emploi
1
Instructions for installation
Patent pending
UK Registered Design
R3 May 2020 200799_1
Volta 42” & Volta 32” Pryzm
Inset Fire Conversion Kit
2
Conversion Kit Check List P3
Installation- Introduction P4
Assembly- Pre-fabricated Chimney Breast P5
Assembly- Existing Masonry Chimney Breast P6
Assembly- Fire Conversion Kit Installation P7
Assembly- Fire Conversion Kit Installation continued P8
Installation- Positioning the fire P9
Installation- Magnet Bracket P10
Installation- Fixing the Fire P11
Installation- Fixing the Fire continued P12
Installation- Fitting the Trim P13
Maintenance P14
200799_1
Contents
3
200799_1
Conversion Kit Check List
Please ensure all fixings are present before commencing installation. If anything is missing please
call Customer Services on 01914300901 or email us at customerservices@bemodern.co.uk
2X
Side Panels
4X
Angle Brackets
18 X
No.8 x15mm
Domed-Head
Screws
4X
No.8 x13mm
Pan-Head
Washer Screws
4X
10 Ø x 4mm
Magnets
1X
Magnet Bracket 2X
Fire Support
Brackets
1X
Pre-assembled 1000L or 750L MDF Framework
Dependant on the model purchased
1X
1000L Trim or 750L Trim
Dependant on the model purchased
Note: Please be sure to take extra care when
removing the trim from the packaging
and handling it during installation.
4
Installation Introduction
200799_1
Before the product can be installed, consideration will need to be given to routing the power supply to the
fire. This will affect the stages of the installation process. We advise a qualified electrician conduct any
electrical parts of the installation.
Note: A single wall socket is required for the operation of the fire, please refer to the separate fire
instructions for further information.
This product has been designed to be installed into a pre-fabricated, or existing Masonry chimney breast.
Please seek advice from a professional, with reference to the structural integrity of the installation site.
If the product is to be installed into a open chimney or flue, it is important that the chimney/flue is blocked
off to prevent any up/down draughts and falling debris which could restrict and alter the airflow of the
product.
The product should never be sealed into an opening with the use of silicones or adhesives as this can also
alter the airflow and hinder any future servicing of the product.
It is essential to include a lintel at the required height to ensure the appliance does not support the weight
of the finished wall.
A pre-assembled MDF framework has been supplied to ensure that the product is installed at the required
minimum internal clearances for operation. Before commencing with installation please ensure the Fire
Support Brackets have been attached to the MDF framework, these set the minimum depth required for
installation- 238mm. As shown in Diagram 1 below.
Diagram 1
Fix the 2 x Fire Support Brackets using 4 x No.8 x15mm Domed-Head Screws into the pre-drilled holes on
the MDF framework . 2 x per bracket.
Fire Support
Brackets
MDF
Framework
For installation into a pre-fabricated chimney breast follow the instructions on Page 5 then continue onto
Page 7.
For installation into a existing Masonry chimney breast follow the instruction on Page 6 then continue onto
Page 7.
MDF
Framework
H
(mm)
W
(mm)
Min Inset
(mm)
Volta 42” 518 1102 Min 238
Volta 32” 518 852 Min 238
5
Assembly- Pre-fabricated Chimney Breast
200799_1
Before commencing further with the installation please ensure the 2 X Fire Support Brackets have been
attached to the MDF Framework, these set the minimum depth required for installation- 238mm. As shown
on Page 4.
Decide on the installation height of the fire and construct the studwork around the MDF Framework. The
studwork construction in Diagram 2 is for guidance only.
Ensuring the front face of the MDF framework is flush with the studwork, fix in position through the pre-drilled
holes in the MDF Framework. 3 x fixing holes in the top and bottom and 1 x fixing hole in each side.
Diagram 2
MDF
Framework
Fire Support
Brackets
Studwork
Finishing
Plasterboard, skim and decorate the chimney breast, before installing the fire. As shown in Diagram 3.
Note: The fire is installed in a later procedure.
Diagram 3
6
Assembly- Existing Masonry Chimney Breast
200799_1
Before commencing further with the installation please ensure the 2 X Fire Support Brackets have been
attached to the MDF Framework, these set the minimum depth required for installation- 238mm. As shown
on Page 4.
We recommend sealing the MDF Framework using an appropriate sealer, especially if the installation site is
damp, however this is down to the discretion of the installer.
Decide on the installation height of the fire and using the pre-assembled MDF Framework for guidance,
mark and cut an opening in the brickwork so that the MDF Framework can be fixed flush with the face of
the brickwork. As shown in Diagram 4.
Diagram 4 is for guidance only, the final construction will be dependant on how the existing chimney
breast is built, if a lintel is required, please seek advice from a professional , with reference to the structural
integrity of the installation site.
Ensuring the front face of the MDF Framework is flush with the brickwork, fix in position through the pre-
drilled holes in the MDF Framework. 3 x fixing holes in the top and bottom and 1 x fixing hole in each side.
Alternative fixing points maybe be required depending on the material being fixed into.
Diagram 4
MDF
Framework
Fire Support
Brackets
Lintel
Diagram 5
Finishing
Pasteboard or Patch up, skim and decorate the chimney breast, before installing the fire. As shown
Diagram 5.
Note: The fire is installed in a later procedure.
7
Assembly- Fire Conversion Kit Installation
200799_1
Remove the existing fire side panels from either side of the fire, as shown in Diagram 6.
Retain the 10 x No.8 x12mm Domed-Head Screws. 5 x per side. The side panels are no longer required
and can be discarded.
If applicable remove the transit brackets from the bottom of the fire, as shown in Diagram 7. Remove the
4 x No.8 x12mm Domed-Head Screws.
The transit brackets and screws are no longer required and can be discarded.
Diagram 6
Diagram 7
8
Assembly- Fire Conversion Kit Installation Continued ……
200799_1
Fix the 4 x Angle Brackets using the previously retained- No.8 x12mm Domed-Head Screws. 2 x per bracket.
Ensure the brackets are fixed in the correct orientation- the small tab on each bracket should be
positioned, as shown in Diagrams 8 & 9.
Diagram 8
Diagram 9
Tab
Tab
The tabs are used to
ensure the brackets
are installed at the
correct distance from
the finished wall
surface in later
procedures.
9
Installation- Positioning of the Fire
200799_1
Note: Before positioning the fire, connect the fire to a power supply.
The next step is to position the fire in the opening.
Angle the fire into the opening, as shown in Diagram 10, taking care
not to damage the bottom long edge of the finished opening.
Once clear of the opening, position the fire towards the back of the opening, so it is clear of the front edge
and the MDF Framework in the opening is exposed, as shown in Diagram 11. This will enable the magnet
bracket to be fitted. See page 10
Ensure the product is connected to the power supply before proceeding further.
Diagram 10 Diagram 11
Note: Dependant on the model
purchased the fire may require a
two adult person lift.
10
Installation- Magnet Bracket
200799_1
With the fire pushed to the rear of the opening.
Install the Magnet Bracket, as shown in Diagram 12, using the supplied 2 x No.8 x15mm Domed-Head
Screws, to fix into the pre-drilled holes in the MDF Framework, this will ensure the bracket is fitted centrally in
the opening.
Before fixing in position align the tabs on either end of the bracket with the face of the finished wall
surface, as shown in Diagram 13.
This will ensure the bracket is installed at the correct distance from the front face for the magnet to engage
correctly with the trim in a later procedure.
Diagram 12
Diagram 13
Finished Wall
Surface
Tab
Tab
Finished Wall
Surface
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels bemodern Cheminée intérieure
bemodern
bemodern 2603 HE900E Instructions d'installation
bemodern
bemodern Pryzm 750 Manuel utilisateur
bemodern
bemodern Elgin & Hall Instructions de montage
bemodern
bemodern Pryzm 750 Mode d’emploi
bemodern
bemodern Beadnell Manuel du propriétaire
bemodern
bemodern 2100 Manuel utilisateur
bemodern
bemodern 2983 Manuel utilisateur
bemodern
bemodern Pryzm 1000 Manuel utilisateur
bemodern
bemodern EVOLV GAS FIRES 520 Slimline Inset Guide de l'utilisateur
bemodern
bemodern Pryzm 750 Manuel utilisateur
bemodern
bemodern 600CF Manuel utilisateur
bemodern
bemodern Arteon Pryzm 10003SL Manuel de programmation
bemodern
bemodern 2668 Manuel utilisateur
bemodern
bemodern BROSELEY EVOLUTION Canterbury Remote Manuel
bemodern
bemodern EARDF16NG Guide de l'utilisateur
bemodern
bemodern Arteon Pryzm 10003SL Mode d’emploi
bemodern
bemodern Arteon Pryzm 10003SL Mode d’emploi
bemodern
bemodern PRIZM MEDIAVUE Manuel de programmation
bemodern
bemodern BM-05XXX1 Manuel utilisateur
bemodern
bemodern 580 Deluxe Inset Manuel utilisateur
