bemodern 2983 Manuel utilisateur
1
16” and 22” 75mm Electric Fire
Instructions for use
Patent pending
UK Registered Design
R1 Jan 2020 200797_1
Complete with Remote Control
Model 2983 / 2921
2
Contents
Tech Specs 3
Safety Info 4 –5
Fixing the appliance 6 –7
Attaching the Trim 7
User Instructions 8 - 13
Maintenance 14
General information 15
Guarantee 16
200797_1
3
Technical Specification
Model No.: 2893 / 2921
Supply Voltage: AC 230-240V 50Hz
Maximum power consumption: 2KW
Power for flame effect: 13W (LED 5W + Motor for flame 8W)
Heat Output:
Nominal heat output (Pnom): 2KW
Minimum heat output (indicative) (Pmin): 1KW
Maximum continuous heat output (Pmax): 2KW
Auxiliary Electricity Consumption:
At nominal heat output (elmax): 14W
At minimum heat output (elmin): 14W
In standby mode (elSB): 0.48 W
Single
stage heat output and no room temperature control No
Two
or more manual stages, no room temperature control No
With
mechanic thermostat room temperature control No
With
electronic room temperature control No
Electronic
room temperature control plus day timer No
Electronic
room temperature control plus week timer Yes
Room
temperature control, with presence detection No
Room
temperature control, with open window detection No
With
distance control option No
With
adaptive start control Yes
With
working time limitation No
With
black bulb sensor No
Type of heat output / room temperature control
Other Control Options
20797_1
4
Safety Information
Read all of the instructions carefully before using the appliance.
For indoor use only This appliance is not suitable for use outside the house and only
suitable for well insulated spaces or occasional use.
Do not use this appliance in the immediate surroundings of a bath, a shower or a
swimming pool or any wet area
This fire must not be located immediately below a socket-outlet.
This appliance must be earthed.
This appliance must not be supplied through an external switching device, such as a
timer, or connected to the circuit that is regularly switched on and off by utility in order
to avoid a hazard due to the inadvertent resetting of the thermal cut out.
A non-rewirable plug fitted with a 13A fuse is supplied. Should the fuse or plug need
replacing, and you are competent to do so, it must be replaced with a 13A fuse or
plug being 13A BS1363A approved.
If the power cord is damaged, it must be repaired by the manufacturer, its authorised
service centre or professional person.
The meaning of this symbol is “DO NOT COVER”. Warning: in order to avoid
overheating, do not allow the appliance to be covered or let the air inlet / outlet to
become obstructed. Please note the warning symbol on the appliance (see above).
To reduce the risk of fire, keep textiles, curtains, or any other flammable material a
minimum distance of 1 meter from the air outlet.
Keep the power cord away from hot surfaces and hot conditions. Do not route the
power lead in front of the appliance.
Do not use this fire in rooms that have explosive gas in them (for example petrol), or if
you are using solvents, glue, aerosol spray or in flammable paints, as these may catch
fire.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
200797_1
5
Safety Information (continued)
Children and vulnerable people must be supervised at all times when using this
appliance, as some parts can become very hot and cause burns.
Do not use this appliance in small rooms when they are occupied by persons not
capable of leaving the room on their own, unless constant supervision is provided.
Cleaning and user maintenance shall not be made by children without supervision.
Children aged from 3 years and less than 8 years only can switch on / off the
appliance provided that it has been placed or installed in its intended normal
operating position and instructions and supervisions concerning the safe way of the
use of the appliance are offered. Children aged from 3 years and less than 8 years
shall not plug in, regulate and clean the appliance or perform user maintenance.
This appliance shall not be played with by children.
Children of less than 3 years should be kept away unless continuously supervised.
200797_1
6200797_1
Securing the Appliance
Prior to installation / securing the fire select the preferred fixing method.
A. Securing the fire into position using the fixing holes in the rebate stops.
B. Securing the fire using the back panel clamp.
Back panel / cavity opening size
Model A B C
Model 2893 –16” Version 565 413 75 min
Model 2921 - 22” Version 595 570 75 min
Fixing method A.
Position the fire in the back panel opening ensuring it is centralised. Depending on the
back panel medium , mark the hole positions then remove the fire, drill and plug the
holes ensuring the correct fixings are used for the wall medium. *NOTE Fixings are not
supplied. Once fixing holes have been plugged replace the fire and secure in position
via the holes in the rebate stops.
Rebate stops
Fixing Method A
601227_1 7
Place the four 10mm magnets on the rebate stop tabs and position the trim over the
fire magnetically securing it to the fire and holding it in position.
Fixing method B.
Loosely attach the back panel clamp to the top of the fire as shown below in Figure 1.
Hook the clamp under the back panel so it site behind the panel and centralise the fire
in position. Once in the correct position hold the fire against the back panel and pull
the bracket forwards Figure 2. Tighten the bracket screws to secure the fire in position
Securing the Appliance
Figure 1 Figure 2
Attaching the Trim
8
User Instructions
WARNING! Do not operate the appliance if it is damaged or has malfunctioned. If you
suspect the appliance is damaged or has malfunctioned call a qualified service
engineer to inspect the appliance, and replace any part of the electrical system if
necessary, before reuse.
WARNING! To reduce the risk of fire, keep textiles, curtains, or any other flammable
material a minimum distance of 1 meter from the air outlet.
MAKE SURE the plug fits tight in the outlet. Faulty wall outlet connections or loose plugs
can cause the outlet to overheat.
Do not disconnect the power at the mains supply whilst the appliance is running. Use
the functions on the remote to turn the fire off and ensure the mains switch has been
moved to the off position before disconnecting.
PREPARATION FOR USE
The appliance can be operated by both remote control and the manual controls on
the appliance. NOTE: To use either the remote or the manual functions the main
power switch must be in the ‘ON’ position. (See below)
Batteries
Ensure that the handset batteries are new and inserted correctly.
Main Power Switch
The mains power switch is located on the control panel behind the door of the stove.
This needs to be switched ON before operating either the remote or manual controls.
A long beep will be heard to indicate the fire is ready for use.
200797_1
9
User Instructions Continued
Manual control panel
200797_1
Use the ON / OFF switch to power on the heater (set it to standby mode).
In standby mode, the heater can be operated either manually by the switches
located behind the fret or by the supplied remote control.
Heater powered off
Heater powered on, set to standby
mode
-
Press to switch the flame
effect
ON / OFF
-
Press and hold to toggle
between
5 different flame effect colours
-
Press once to activate low level
heating(1000W)
-
Press twice to activate high level
heating(2000W)
-
Press three times to switch off
heating
-
Press to toggle between 7
different fuel bed effect colours
BACKLIGHT
Main
Power
Switch
Appliance Control
Panel
NOTE: The heater should be powered on using the Main Power switch before it can be
operated using remote control
10
User Instructions Continued
Remote control operation
200797_1
The remote control requires 2 x AAA size batteries.
Open the battery compartment. Pull tab downwards and lift out the cover, insert the
batteries noting the polarity indicated in the battery compartment.
Keep batteries out of reach of children.
Remote control operations are identical to the functions on the control panel.
The remote control must be pointed directly at the sensor on control pad.
Switches the appliance on
Switches the appliance into
standby mode
Set day / time
Decrease temperature
Decrease hour / minute
Confirm selection
Set automatic heating mode
Press once to activate low
heat setting
Press twice to activate high
heat setting
Press three times to switch of heat
Toggle between the 7 different
fuel bed light colours
Toggle between the 5 different
flame effect colours
Timer on / off
Cancel
Menu down (Change day)
Increase temperature
Increase hour / minute
Timer set
Menu up (Change day)
2 x AAA
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels bemodern Cheminée intérieure
bemodern
bemodern 2599R Manuel utilisateur
bemodern
bemodern BM-121 2 Series Manuel utilisateur
bemodern
bemodern ELSIE 960 Manuel utilisateur
bemodern
bemodern Beadnell Manuel du propriétaire
bemodern
bemodern BM-081 2 Series Manuel utilisateur
bemodern
bemodern Arteon Pryzm 10003SL Mode d’emploi
bemodern
bemodern 800CF Manuel utilisateur
bemodern
bemodern Pryzm 1000 Manuel utilisateur
bemodern
bemodern 2893 Manuel utilisateur
bemodern
bemodern 580 Deluxe Inset Manuel utilisateur
bemodern
bemodern Juliette Instructions de montage
bemodern
bemodern 600CF Manuel utilisateur
bemodern
bemodern 2100 Manuel utilisateur
bemodern
bemodern BM-10 Manuel utilisateur
bemodern
bemodern Arteon Pryzm 10003SL Mode d’emploi
bemodern
bemodern EVOLV GAS FIRES 520 Slimline Inset Guide de l'utilisateur
bemodern
bemodern BROSELEY EVOLUTION Canterbury Remote Manuel
bemodern
bemodern EARDF16NG Guide de l'utilisateur
bemodern
bemodern Arteon Pryzm 10003SL Manuel de programmation
bemodern
bemodern 2599M Manuel utilisateur
