Belair 200 Manuel utilisateur
BelAir200 General Availability
BelAir200
Installation Guide
Document Date: February 19, 2004
Document Number: BDTK20001-A02
Document Status: Standard
Security Status: Confidential
Customer Support: 613-254-7070
© Copyright 2004 by BelAir Networks.
The information contained in this document is confidential and proprietary to BelAir Networks. Errors and Omissions Excepted.
Specifications may be subject to change.
Page 1 of 17
BelAir200 Installation Guide
Contents
About this Document.................................................................................. 2
Introduction ................................................................................................... 3
Mounting the BelAir200.............................................................................. 8
Regulatory Statements ..............................................................................13
Detailed Table of Contents......................................................................15
About this Document
This guide provides the information you need to physically install the
BelAir200.
Related Documentation
The following titles are BelAir reference documents:
•
BelAir200 Building Coverage Deployment Guidelines
•
BelAir200 User Guide
February 19, 2004 Confidential Page 2 of 17
Document Number BDTK20001-A02 Standard
BelAir200 Installation Guide
Introduction
BelAir Networks recommends that you prepare for the installation of your
Belair200 as follows:
1. Verify the contents of your shipping container. Be sure to note any
external carton damage with your shipper to facilitate any future warranty
claims. See the section “Shipping Contents” on page 4.
2. Fill out the included
Configuration Worksheet
to record the important
installation and network configuration settings.
3. Analyze your site to determine the optimum mounting location. To assist
you, refer to:
— the section “Site Survey” on page 6
— the
BelAir200 Building Coverage Deployment Guidelines
— your authorized reseller
4. Mount the Belair200 by following the steps in the procedure the section
“Mounting the BelAir200” on page 8.
5. Configure the BelAir200 for operation. Refer to the
BelAir200 User Guide.
6. Verify proper operation of the Belair200.
WARNING! Only personnel qualified by BelAir Networks or by one of its authorized
resellers or channel partners should install the BelAir200.
WARNING! This entire document, including the regulatory statements section, should be
read before attempting to install or operate the BelAir200.
February 19, 2004 Confidential Page 3 of 17
Document Number BDTK20001-A02 Standard
BelAir200 Installation Guide
Shipping Contents
Table 1 describes how the standard BelAir200 items are packaged for shipping.
Table 1: BelAir200 Shipping
Box Contents
1 (of 2)
See Figure 1 on page 5.
BelAir200
AC mains power pigtail
Quick Configuration Guide Card
User Guide on CD-ROM
battery unit (if ordered)
2 (of 2)
See Figure 2 on page 6.
universal mounting bracket
threaded nipple
lock nut
decorative finial
hardwall anchors (quantity of 4)
8-inch worm drive (jubilee) clamp (quantity of 2)
drill template
February 19, 2004 Confidential Page 4 of 17
Document Number BDTK20001-A02 Standard
BelAir200 Installation Guide
Figure 1: Contents of Box 1,without BelAir200 Unit
February 19, 2004 Confidential Page 5 of 17
Document Number BDTK20001-A02 Standard
BelAir200 Installation Guide
Figure 2: Contents of Box 2, BelAir200 Mounting Kit
Site Survey
Due to differences in component configurations, physical placement and
environmental considerations, every application is unique. BelAir Networks
recommends that a site survey be completed to best determine your coverage
needs, installation limitations and optimal node configurations. Contact an
authorized reseller to help you with this planning.
Antenna Type and Placement
Proper antenna placement, orientation and selection are critical factors in
maximizing network performance. The antennas are typically placed between
5 m and 10 m above ground level; although alternate installations can be used.
Additionally, the antennas should be located with clear lines of site to adjacent
equipment in the system and free from obstruction by buildings, foliage and
passing traffic.
WARNING! Only antennas approved by BelAir Networks may be used in conjunction with
the BelAir200. Contact BelAir Networks for an up-to-date list of available
approved antennas. Use of any other antenna may exceed FCC or Industry
February 19, 2004 Confidential Page 6 of 17
Document Number BDTK20001-A02 Standard
BelAir200 Installation Guide
Canada regulatory requirements and void the operator’s right to operate the
radio equipment.
WARNING! Installers must ensure the BelAir200 is mounted in such a manner and in such
a location that access to the antennas by the general population is minimized.
Access to the antennas by the general population should be limited to greater
than 20 cm (8 inches) during normal operation.
February 19, 2004 Confidential Page 7 of 17
Document Number BDTK20001-A02 Standard
BelAir200 Installation Guide
Mounting the BelAir200
Only qualified personnel should mount the Belair200.
The BelAir200 is designed to be mounted on a surface or
structure that is capable of supporting its weight (28 pounds). It
is the responsibility of the customer to ensure the strength of
the structure to be mounted to.
The Belair200 is supplied with a standard mounting kit in Box 2 that
accommodates pole or wall mounting in either an upright or upside-down
orientation. If your mounting requires a custom solution, contact BelAir
Networks.
Installation Procedure
1. Remove the Belair200 from its packaging in Box 1. See Figure 3
Figure 3: BelAir200 in its Packaging
February 19, 2004 Confidential Page 8 of 17
Document Number BDTK20001-A02 Standard
BelAir200 Installation Guide
2. With a Philips screwdriver, remove the two lower plastic covers.
There are two screws per cover. Keep these screws because you will use
them later.
Figure 4: Removing Lower Covers from BelAir200
3. Familiarize yourself with the connector field. See Figure 5 on page 10,
If you are making external backhaul antenna connections, this is a good
time to decide which radio port to use. Be sure to record this information
on the
Configuration Worksheet
.
February 19, 2004 Confidential Page 9 of 17
Document Number BDTK20001-A02 Standard
BelAir200 Installation Guide
Figure 5: Connection Field
4. If you are using the optional battery pack, remove the battery access door
and insert the battery into its compartment. Install the battery door and
plug in the battery connector.
Note: Do not force the battery connector; it is “keyed”.
5. Remove the mounting kit from Box 2 and familiarize yourself with the
components.
6. If you are mounting to an aluminium, concrete or wood pole, skip to
step 9.
7. Locate the drill template and using an appropriate ladder or elevating
device, mark and drill the four mounting holes for the hardwall anchors.
Follow the instructions found in the bag of anchors.
Caution must be observed when working around high voltage
lines. Be sure to “Check Overhead” before ascending pole or
wall. Depending on your location, you may need the services of a
Certified Contractor to obtain access to utility poles.
February 19, 2004 Confidential Page 10 of 17
Document Number BDTK20001-A02 Standard
Table des matières
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité