BEC 6200WZL Manuel utilisateur

BEC 6200WZL

4G/LTE Cellular Broadband Router

Quick Start Guide

BEC 6200WZL 4G/LTE Cellular Broadband Router

Package Contents

BEC 6200WZL 4G/LTE Cellular Broadband Router

This Quick Installation Guide

CD containing User Manual

RJ-45 Ethernet Cable

Two 3G/4G-LTE detachable antennas

Power adaptor



Warning

Do not use the router in high humidity or high temperatures.

Do not use the same power source for the router as other equipment.

Do not open or repair the case yourself. If the router is too hot, turn off

the power immediately and have it repaired at a qualified service center.

Avoid using this product and all accessories outdoors.

Attention

Place the router on a stable surface.

Only use the power adapter that comes with the package. Using a

different voltage rating power adaptor may damage the router.

PLEASE READ THE QUICK START GUIDE AND FOLLOW THE

STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU

INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.

IF YOU NEED MORE INFORMATION ON THIS SOFTWARE

CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON

CD-ROM.

Quick Start Guide



Front Panel LEDs

LED

STATUS

DESCRIPTION

Power

Green

System is up and ready

Red

Boot failure

Ethernet Port

LAN 1 ~ 4

Green

LAN Port is connected to an Ethernet unit, e.g. PC, Notebook, Xbox

Blinking

Data being transmitted/received

Note: port #4 can be configured as WAN port for broadband connectivity

EWAN on LAN 4

Green

BEC 6200WZL is successfully connected with a broadband connection device.

Blinking

Data being transmitted/received

Wireless

Green

Wireless connection established

Blinking

Data being transmitted / received

WPS

Green

Wireless client has been connected via WPS successfully

Blinking

WPS is enabled and ready for other wireless clients to join

3G/4G

(Received Signal

Strength Indicator)

Green

RSSI greater than -69 dBm. Excellent signal condition

Green

Flashing quickly

RSSI from -81 to -69 dBm. Good signal condition

Orange

Flashing quickly

RSSI from -99 to -81 dBm. Fair signal condition.

Orange

Flashing slowly

RSSI less than -99 dBm. Poor signal condition.

Orange

No signal and the 4G_LTE module is in service

Off

No LTE module or LTE module fails

Internet

Green

WAN IP received and traffic is passing thru the device.

Red

WAN IP request failed.

Off

BEC 6200WZL is either in bridged mode or WAN connection not ready.

BEC 6200WZL 4G/LTE Cellular Broadband Router

Rear Panel Connectors

PORT

MEANING

LTE Antenna

Screw the supplied LTE antennas onto the antenna connectors on both sides.

SIM Card Slot

Insert the mini SIM card (2FF) with the gold contact facing down.

Push the mini SIM card (2FF) inwards to eject it

WAN

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when

connecting to a PC or an office/home network of 10Mbps /100Mbps.

Ethernet LAN

(1~4)

Connect to Fiber/ Cable/ xDSL Modem with a RJ-45 cable

WAN Port (LAN port 4) can also be a regular Ethernet LAN port.

Reset

After the device is powered on, press it 6 seconds or above: to restore to factory

default settings (this is used when you cannot login to the router, e.g. forgot your

password)

WPS &

Wireless

On/Off

By controlling the pressing time, users can achieve two different effects:

(1) WPS*1: Press &hold the button for less than 6 seconds to trigger WPS function.

(2) Wireless ON/OFF button: Press & hold the button for more than 6 seconds to

On/Off the wireless.

Power Jack

(DC)

Connect the supplied Power Adapter to this jack.

Power Switch

Power ON/OFF switch

Quick Start Guide

Hardware Connection

Hardware Installation

1. Power Connection

Plug in the supplied power adapter to the wall jack, the other side to the 6200WZL then

power ON the 6200WZL by pressing the Power On/Off button.

2. LAN Connection

Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other side

to the PC’s Ethernet interface.

Attention

Connect the detachable 3G/4G-LTE antennas to the two jacks on the

back of the device and make sure they are firmly screwed in.

The MAIN antenna connector is used for primary 3G/4G-LTE.

If deciding to use ONE antenna, make sure the MAIN antenna connector

is being connected at all times.

BEC 6200WZL 4G/LTE Cellular Broadband Router

3. WAN Link Interface and Connection

BEC 6200WZL support dual WAN interfaces, 4G LTE and EWAN. <Please refer to User

Manual for detailed Internet setup>

3.1 4G_LTE Connection

Slide the SIM card into the card slot of the device with the gold contact facing down. Make

sure that the SIM card has been slid into the bottom of the slot with a click. When removing

the SIM card, press the SIM card again it will be ejected from the card slot.

3.2 EWAN Connection

Connect RJ-45 Ethernet cable to the Ethernet WAN port, and connect the other side to

another alternative broadband device, such as Cable Modem, VDSL, Fiber Modem or PON

optic lines.

WARNING: Please power off the device before inserting or removing the SIM

card.

Quick Start Guide

Connecting to the Router

The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached

PC to this router is in the same subnet and has an IP address in the range between 192.168.1.1

~ 192.168.1.253.

Open a web browser and type http://192.168.1.254 in the URL address bar.

The login prompt will appear. Input the default username (admin) and password (admin) for

Account type, Administrator. *This username / password may vary by different Internet Service Providers.

Quick Setup Your Router

Step 1: Time Zone configuration

Enable and select your Time Zone then click Continue to go on to the next step

URL Address bar: type

http://192.168.1.254

Before start configuring the 6200WZL, make sure you have the WAN port connected

with your Internet box or fiber line.

Time Zone: select your time zone

Next Step: click Next

BEC 6200WZL 4G/LTE Cellular Broadband Router

Step 2: WAN / Internet Connection Setup

Select the appropriate WAN protocol then fill out the information provided by your ISP in all

relevant parameters. For 3G/4G_LTE connection, if your Service Provider is not on the list,

please select Other and fill out all of the appropriate fields.

Step 3: Setup Wireless Connection

Step 4: Saving Configuration

Wait for 10 - 20 seconds for the router to establish an Internet connection.

If no responses for more than 30 seconds please check the SIM Card connection or/and

information is/are being input properly.

Step 5: Quick Start Wizard Complete

“Success!” message will be shown if the Internet connection is ready to go.

If not, please check your WAN, Internet Connection, setup again.

Please see the relevant sections of User Manual for detailed information.

Troubleshooting

1. None of the LEDs are on when you turn on the router.

Check the connection between the adapter and the router. If the error persists, you may have

a hardware problem. In this case you should contact technical support.

WLAN Service: select Enable

ESSID: Assign an unique name

Channel ID: pick from 1~11

Security Mode: select a mode

- Disable (No security)

- WPA

- WPA2 (Most secure one)

- WPA / WPA2 (auto detect WPA

mode with wireless clients)

- WEP (Less secure one)

Security Parameters: key for wireless

authentication

- WPA / WAPA2 Share Key: Assign a

key between 8 ~ 63 characters.

- WEP: select Open System, use

default WEP Key 1then assign 26

Hex codes

Next Step: click Continue

Quick Start Guide

2. You have forgotten your router login and/or password.

Try the default login and password, please refer to User Manual. If this fails, you can restore

your router to its factory settings by holding the Reset button on the back of your router for 6

seconds or more.

3. Can’t ping any PCs on the LAN.

Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC

connected. If it is off, check the cables between your router and the PC. Make sure you have

uninstalled any software firewall for troubleshooting. Verify that the IPaddress and the subnet

mask are consistent between the router and the workstations.

uninstalled any software firewall for troubleshooting. Verify that the IPaddress and the subnet

mask are consistent between the router and the workstations.

Product Support and Contact Information

Most problems can be solved by referring to the Troubleshooting section in the User Manual.If

you have other inquiries or need further technical support, please contact with your Internet

Service Provider or visit us at www.bectechnologies.net.

Autres manuels pour 6200WZL

Table des matières

Autres manuels BEC Routeur sans fil

BEC

BEC 430M Manuel utilisateur

BEC

BEC MX-210NP Manuel utilisateur

BEC

BEC RidgeWave 6900 Manuel utilisateur

BEC

BEC 6300VNL Manuel utilisateur

BEC

BEC 6800RUL Manuel utilisateur

BEC

BEC MX-200A ODU Manuel utilisateur

BEC

BEC 6200WZL Mode d'emploi

BEC

BEC MX-241NP Manuel utilisateur

BEC

BEC RidgeWave BEC 7000 R25 Manuel utilisateur

BEC

BEC 6300VNL Manuel utilisateur

BEC

BEC BEC 6500 Series Manuel utilisateur

BEC

BEC BEC 6900 R21 Manuel utilisateur

BEC

BEC MX-1000 Manuel utilisateur

BEC

BEC VG2600 Manuel utilisateur

BEC

BEC MX-210NPV Manuel utilisateur

BEC

BEC 6300VNL Manuel utilisateur

BEC

BEC BiPAC 6300VNPOZ Manuel utilisateur

BEC

BEC 4700A Manuel utilisateur

BEC

BEC M2M MX-200Ae Manuel utilisateur

BEC

BEC 6600AEL Manuel utilisateur

BEC

BEC 6300VNL Manuel utilisateur

BEC

BEC 6300VNL Manuel utilisateur

BEC

BEC EG-210N Manuel utilisateur

BEC

BEC MX-210NP R7-Q Manuel utilisateur

Manuels Routeur sans fil populaires d'autres marques

Milesight

Milesight UG67 Manuel utilisateur

Airlogic

Airlogic AirSync Class 1 Manuel du propriétaire

Samsung

Samsung WCH730B Manuel utilisateur

TELEFONICA

TELEFONICA USB Adapter Manuel utilisateur

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manuel utilisateur

Askey

Askey RAC2V1K Manuel utilisateur

Alloy

Alloy WLF2454AP-S Manuel utilisateur

TP-Link

TP-Link TL-WR542G Manuel utilisateur

NETGEAR

NETGEAR WNR2000v4 Manuel utilisateur

Hama

Hama 53120 Manuel utilisateur

Intellinet

Intellinet 524582 Manuel utilisateur

Asus

Asus RT-N10P Manuel utilisateur

D-Link

D-Link DIR-506L Manuel utilisateur

Sapido

Sapido GR297n Manuel utilisateur

Asus

Asus DSL-N55U Manuel utilisateur

AMTC

AMTC WR7502 Manuel utilisateur

Compaq

Compaq CP-2W - iPAQ Connection Point Manuel utilisateur

SMC Networks

SMC Networks WBR14-N2 FICHE Manuel utilisateur