BEA IS40P Manuel utilisateur

75.5696.02 EN 20120213 Page 1 of 8

DESCRIPTION SPECIFICATION

SENSOR TILT ANGLE 15° to 45°

SUPPLY VOLTAGE 12 to 24 VAC ±10%

12 to 24 VDC +30% / -5%

MAIN FREQUENCY 50 to 60 Hz

POWER CONSUMPTION < 2 W

RELAY OUTPUT

- Max. Voltage

- Max. Current

- Max Switching Power

2 Relays with switch-over contact (voltage free)

60 VDC / 125 VAC

1 A (resistive)

30 W (DC) / 60 VA (AC)

INSTALLATION HEIGHT 8 ft - 16 ft (2.5 m – 6 m)

TEMPERATURE RANGE -22°F ( -30°C) to + 140°F (60°C)

PROTECTION DEGREE IP65 / NEMA 4

NORM CONFORMITY Electromagnetic compatibility (EMC) according to 2004/108/EEC, R&TTE: 1999/5/EC

DIMENSIONS (D X W X H) 5 in × 4 in × 3.75 in (127 mm × 102 mm × 96 mm)

MATERIAL

- Housing

- Face

ABS

Polycarbonate

COLOR

- Housing

- Face

Black

Transparent Purple

CABLE LENGTH 32 ft (10 m)

TECHNOLOGY INFRARED

RADIATED FREQUENCY 875 nm

RADIATED POWER DENSITY < 250 mW/m²

DETECTION MODE Presence

MAXIMUM DETECTION FIELD 10 ft x 10 ft (3 m x 3 m)

OUTPUT HOLD TIME 0.5 s – 9 s (Activation Relay) / 0.5 s (Presence Relay)

REACTION TIME 250 ms

MINIMUM TARGET SPEED 0 in/s (0 cm/s)

LED SIGNAL Green = Activation Relay / Red = Presence Relay

SENSOR ANGLE 15°, 30°, 45°

IS40P

USER’S GUIDE

ACTIVE INFRARED (IR) PRESENCE SENSOR

IS40P

- The IS40P uses Active

Infrared technology for

presence detection.

SPECIFICATIONS

1. IR angle indicator

2. LED’s

3. IR emitters

4. Sensor angle adjustment

5. Bracket

6. Cable

DESCRIPTION

CAUTION

1 9/16

1 1/16

1 1/16 1 1/16

4 1/8

1/2

1 1/4

1 1/2

6.25

2.5

75.5696.02 EN 20120213 Page 2 of 8

PRECAUTIONS

This device IS NOT intended for use as a safety sensor.

Not recommended for dynamic envioronments. (snow, rain, fog, etc.)

Shut off all power before attempting any wiring procedures.

Maintain a clean & safe environment when working in public areas.

Constantly be aware of pedestrian/vehicle trafc around the area.

Always stop pedestrian/vehicle trafc through the doorway when performing tests that may result in unexpected reactions by the door.

ESD electrostatic discharge: Circuit boards are vulnerable to damage by electrostatic discharge. Before handling any board ensure

you dissipate your body’s charge.

Always check placement of all wiring before powering up to insure that moving parts will not catch any wires and cause damage to

equipment.

Ensure compliance with all applicable safety standards upon completion of installation.

DO NOT attempt any internal repair of the sensor. All repairs and/or component replacements must be performed by BEA Inc. Unau-

thorized disassembly or repair:

1. May jeopardize personal safety and may expose one to the risk of electrical shock.

2. May adversely affect the safe and reliable performance of the product and will result in a voided product warranty.

DIMENSIONS (inches)

MOUNTING

Wall mounting Ceiling mounting Bracket dimensions

INSTALLATION TIPS

The sensor must be

rmly fastened to

prevent vibration.

The sensor must not

have any object likely

to move or vibrate in

its sensing eld.

DO NOT cover

the sensor.

Remove the bracket from the sensor.

Drill 2 holes accordingly. If necessary, drill an additional

hole to facilitate wire routing. Fix the bracket rmly.

Position the sensor on the bracket

and fasten the angle adjustment screws.

Avoid exposing the

sensor to sudden

temperature changes

Avoid proximity to neon

lamps, uorescent lights

or moving objects

63 0 36

DOOR

63 0 36

DOOR

63 0 36

DOOR

75.5696.02 EN 20120213 Page 3 of 8

WIRING AND RELAY CONFIGURATION

Notes:

1. It is important to adjust sensor angle to position IR eld correctly.

2. To obtain an IR pattern that’s straight down (closest to the door threshold); wall mounted sensors need to be

set at 20º; sensors mounted on an extension bracket or out from the wall should be set to approximately 15º.

3. The graphics above are not to scale and for illustration purposes and represent an approximate IR detection

field when at 16 ft. The point of emphasis is to show the IR detection area with respect to the sensor angles.

SENSOR ANGLE

COM

RED

BLACK

12-24 V

AC-DC

WHITE

GREEN

YELLOW

WHITE/BLACK

GREEN/BLACK

YELLOW/BLACK

COM

Red LED

Presence

1-4

Activation

Relay

Presence

Relay

1 Active Passive

2 Passive Active

3 Passive Passive

4 Active Active

Description Active Passive

Detection COM COM

RELAY

CONFIGURATION

WIRING

Adjust the angle of the sensor to position the detection eld Tighten the screws rmly

RECOMMENDED

SPECIAL APPLICATIONS

CEILING

WALL

15° 30° 45°

ACTIVATION RELAY

PRESENCE RELAY

POWER

RECOMMENDED

Green LED

Presence

12”

75.5696.02 EN 20120213 Page 4 of 8

* Dimensions are approximate.

Approximate default IR pattern size using a 15º sensor tilt angle.

The higher the mounting height the larger the IR pattern.

SENSOR

IR PATTERN SIZE AT 15° SENSOR ANGLE

Mounting

Height

Width * Depth *

A = 8 ft 5 ft 5 ft

B = 10 ft 7 ft 7 ft

C = 11.5 ft 7.5 ft 7.5 ft

D = 13 ft 8.5 ft 8.5 ft

E = 16 ft 10 ft 10 ft

Maximum Mounting Height

IS40P 16 ft

Use of BEA Spotnder may be

utilized to locate IR eld.

75.5696.02 EN 20120213 Page 5 of 8

OUTPUT CONFIGURATION

OUTPUT

CONFIGURATION

PRESENCE RELAY IS40P LED

0 – 6: ALL MODES Activates when object is in presence zone.

ACTIVATION RELAY IS40P LED

0: STANDARD MODE Activates when object is in presence zone

1: PULSE ON ENTRY Activates when object enters presence zone

2: PULSE ON EXIT Activates when object exits presence zone

3: PULSE ON ENTRY FIRST / LAST LINE

(See Example to the Left)

Activates when object enters presence zone

(rst or last line)

4: PULSE ON EXIT FIRST / LAST LINE

(See Example to the Left)

Activates when object exits presence zone

(rst or last line)

5: REMAINS ACTIVE UNTIL PRESENCE

ZONE IS CLEARED

Activates when object is in presence zone

6: REMAINS ACTIVE UNTIL PRESENCE

ZONE IS CLEARED

Activates when object is in presence zone

DOOR EXAMPLE

REMOTE CONTROL PARAMETERS

Red

FIRST LINE

LAST LINE

02 3 4 5 6 78 9

FREQUENCY

AUTOMATIC

LEARN TIME

IR IMMUNITY low medium high

1 min 2 min30 s 10 min 20 min5 min 1 h 2 h1.5 h

IR / Presence Settings

low high

∞

FACTORY

VALUES

Note:The automatic learn time is the amount of time a static

object needs to be in the IR eld before the sensor will learn it.

1 s 2 s

.5 s 4 s 5 s3 s 6 s 8 s7 s 9 s

ACTIVATION RELAY

HOLD TIME

Green

10 REMOTE CONTROL PARAMETERS (CONTINTUED)

DOOR

75.5696.02 EN 20120213 Page 6 of 8

FACTORY

VALUES

IR / Presence Settings (Continued)

IR PATTERN

SIZE

AVAILABLE TARGET SIZE

The target (Target Size)

can vary location within

the eld (IR Pattern Size)

New

Value

Parameter

75.5696.02 EN 20120213 Page 7 of 8

QUESTION A VALUE The number of green ashes

indicates the value of the

chosen parameter.

Check parameter values

REMOTE CONTROL PARAMETERS (CONTINUED)

SENSOR SETUP SEQUENCE / FACTORY VALUES / ACCESS CODE

IMPORTANT: ALWAYS FINISH AN ADJUSTMENT

SESSION BY LAUNCHING A SETUP.

IMPORTANT: ENSURE TO SAVE ANY

CHANGES DURING THE ADJUSTMENT

SESSION VIA PRESSING LOCK LOCK.

RESETTING TO FACTORY VALUES

SETTING AN ACCESS CODE

DELETING AN ACCESS CODE

If you do not know the access code, cycle the power supply.

Within 1 minute, you can access the sensor without introducing any access code or delete the existing access code per the instrucitons above.

12 TROUBLESHOOTING

SYMPTOMS POSSIBLE CAUSES CORRECTIVE ACTION

The red LED is on during rain or

snow.

The presence detection is disturbed

by the rain or snow.

Increase the immunity of the IR eld.

(value 2 or 3 respectively).

The red LED is permanently on

after a setup.

Setup has failed due to motion in the

IR eld during setup.

Launch a setup with the IR area clear of

moving objects.

The door keeps recycling open

or closed.

The sensor detects door vibrations

or environmental disturbances.

Increase IR immunity.

Secure mounting bracket.

The door never closes and the

red LED is on. Objects in the IR detection area.

Wait for learn time to expire and/or

Launch a setup.

Move objects or reduce automatic learn

time.

The door never closed and the

LED(s) is off.

Output relay(s) could be wired or

congured backwards.

Change wiring at output(s) and/or

change relay conguration.

F1 F2

2 A

75.5696.02 EN 20120213 Page 8 of 8

Application requires an access

code or sensor will not unlock

after entering an access code.

You must enter a code or the wrong

code was entered.

Cycle the power. No code is required

to unlock during the rst minute after

powering on. Unlock, then lock and enter

a new access code or “0000” to delete

the current access code.

TROUBLESHOOTING (CONTINUED)

SYMPTOMS POSSIBLE CAUSES CORRECTIVE ACTION

The sensor does not respond to

the remote control.

The batteries in the remote control

are not installed properly, dead or the

remote is poorly aimed.

Verify or replace batteries or aim remote

towards sensor.

The sensor is not powered. Check the power supply of the sensor.

ACCESSORIES

Spotnder

P/N: 10SPOTFINDER

Remote control

P/N: 10REMOTE

Telescoping HD Bracket

P/N: 10HDBRACKET

COMPANY CONTACT

Our Service Technicians can be called 24 hours a day, 7 days a week. For more information visit www.beasensors.com.

Do not leave problems unresolved. If a satisfactory solution cannot be achieved after troubleshooting

a problem, please call BEA, Inc. If you must wait for the following workday to call BEA, leave the door

inoperable until satisfactory repairs can be made. Never sacrifice the safe operation of the automatic

door or gate for an incomplete solution.

After Normal Business Hours

West / Mexico

1-888-419-2564

Central

1-800-407-4545

AK, MI, WI, TX, Canada

1-866-836-1863

East

1-866-249-7937

Phone: 1-800-523-2462 Fax: 1-888-523-2462

For email support contact us at: T[email protected]

Transformer

P/N: 1024VAC

Table des matières

Autres manuels BEA Accessoires

BEA

BEA IXIO-DP3 Manuel utilisateur

BEA

BEA ACTIV8 THREE PULSE Manuel utilisateur

BEA

BEA MAGIC SWITCH CHROMA Manuel utilisateur

BEA

BEA Jamb Style PBJ Series Manuel utilisateur

BEA

BEA BODYGUARD-T Manuel utilisateur

BEA

BEA R2E-100 Manuel utilisateur

BEA

BEA SBK 30 Guide de l'utilisateur

BEA

BEA MAGIC SWITCH CHROMA Manuel utilisateur

BEA

BEA DK-12 Manuel utilisateur

BEA

BEA Fly Manuel utilisateur

BEA

BEA LZR-WIDESCAN Manuel utilisateur

BEA

BEA Eagle Manuel de l'opérateur

BEA

BEA FALCON EX Manuel utilisateur

BEA

BEA WIZARD PLUS Manuel utilisateur

BEA

BEA IXIO-DT1 Manuel utilisateur

BEA

BEA CRYSTAL Manuel utilisateur

BEA

BEA IS40 Manuel utilisateur

BEA

BEA PBR45 Series Manuel utilisateur

BEA

BEA LZR SIGMA Manuel utilisateur

BEA

BEA WIZARD II Manuel utilisateur

BEA

BEA IRIS Manuel utilisateur

BEA

BEA Sparrow Manuel utilisateur

BEA

BEA Eagle HM Manuel utilisateur

BEA

BEA LZR SIGMA Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur