Baxall CDR Series Manuel utilisateur
CDR Series Cameras
Installation Instructions
Please read these instructions first!
2
CDR Series Installation Instructions
IMPORTANT
The first few pages of these instructions contain important information on safety and product
conformity. Please read, and ensure that you understand this information before continuing.
3
Installation Instructions CDR Series
CONTENTS
Introduction .....................................................................................................................4
Product Safety .................................................................................................................5
Radio Frequency Devices ...............................................................................................5
Cautions ...........................................................................................................................6
Connectors and Controls...................................................................................................6
Power Supply Connection .................................................................................................7
Video Connections ............................................................................................................7
Lens Connection ...............................................................................................................7
Lens Selection...................................................................................................................8
Focus Adjustment..............................................................................................................8
System Connections .........................................................................................................9
Menu System
Entering the menu system ..........................................................................................10
Navigating the menu system ....................................................................................... 11
Advanced Menu Map ..................................................................................................12
Basic Menu Map .........................................................................................................13
Basic Menu
White Balance.............................................................................................................16
Gamma .......................................................................................................................16
AGC (Automatic Gain Control) ....................................................................................17
Shutter (EI)..................................................................................................................17
BLC (Backlight Compensation) ...................................................................................18
Sync Menu ..................................................................................................................20
Lens Menu ..................................................................................................................22
Camera ID...................................................................................................................24
Advanced Menu
Auto Black ...................................................................................................................27
Menu Timeout .............................................................................................................28
Video Adjustment ............................................................................................................28
Group Settings ............................................................................................................29
Set Passwords ............................................................................................................30
Info ..............................................................................................................................31
Password Recovery ........................................................................................................32
Specifications ..................................................................................................................33
4
CDR Series Installation Instructions
INTRODUCTION
These instructions cover Baxall CDR series cameras. Read all of these instructions. Use
them to install your camera and have them available for its lifetime. If you have any problems,
contact Baxall Limited. All CDR series cameras are fitted with a Direct Drive (DD) lens
connector, have adjustable back focus and accept C and CS lenses.
Option
Mono
Color
Resolution (TVL)
Sensitivity (lux @ f1.2)
CCD Sensor size
Sony HyperHAD™ CCD
Sony ExviewHAD™ CCD
580 580 580 580 480 480 480 480
0.1 0.90.1 0.90.04 0.40.04 0.4
1/3“ 1/3“1/3“ 1/3“1/2“ 1/2“1/2“ 1/2“
Supply
11 - 40 VDC; 12 - 30 VAC
98 - 260 V AC 50Hz
CDR2233
CDR4233
CDR2235
CDR4235
CDR3223
CDR5223
CDR3225
CDR5225
5
Installation Instructions CDR Series
PRODUCT SAFETY
Installation and servicing is only to be carried out by suitably qualified and
experienced personnel to local or national wiring standards.
Good engineering practice must be carried out at all times and all servicing and
repairs carried out indoors.
All CDR series cameras are to be powered with a class 2 power supply.
Your CDR series camera is fitted with a 1 Amp time-lag fuse located on the rear
board assembly. Replacement must be with an identical type of fuse.
Under no circumstances must the power consumption of the rear Auto Iris
connector exceed 50mA or the Direct Drive connector exceed 25mA.
The CDR series range is designed for use in general purpose CCTV applications
and has no other purpose. Only operate your camera between the temperatures of
-10OC and +50OC.
REGULATORY NOTICES
Federal Communications Commission Part 15 - Digital devices
This Device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference that may cause undesired operation.
CERTIFICATIONS
This product meets the requirements of the following standards:
Electromagnetic Compatibility
EN55022: 1995 limits and methods of measurement of radio disturbance characteristics of
information technology
EN50082-1: 1992 Generic immunity standard
Comprising:
IEC 1000-4-2:1995 Electrostatic discharge
IEC 1000-4-3:1995 Radiated electromagnetic fields
IEC 1000-4-6: Immunity to conducted disturbances, induced by radio-frequency fields
IEC 1000-4-4:1995 Fast transient bursts
Safety
EN 60950: 1992 Safety of information technology equipment, including electrical business
equipment
DECLARATIONS
The manufacturer declares that the equipment supplied with this manual is compliant with
the EMC directive 89/336 EEC and the low voltage directive 73/23 EEC and CE marked
accordingly.
6
CDR Series Installation Instructions
CAUTIONS
In order to avoid damaging the camera note the following points.
1) The camera has threaded mounting points on the top and bottom of the case. Only
use a standard, photographic, mounting-bolt with a 1/4-20 UNC thread.
2) Before fitting the lens make sure that its back will not touch the CCD sensor or
associated components when screwed fully home.
3) Do not touch the image-surface of the sensor. If the sensor is accidentally touched,
only clean it using ethyl alcohol.
4) Do not expose the sensor to direct sunlight as this may impair the performance of
the camera.
5) The weight of your camera is 0.55kg.
6) Only use your camera in a clean, dust-free environment.
7) For outdoor use, an appropriate protective housing conforming to IP65 or UL50 or
better must be used.
CONNECTORS AND CONTROLS
(10)(9)
(12)
230V AC
11-40V D
C
; 12 - 30V A
C
Side View
Top View
(11)
(7)
(6)
(1)
(2)
(3)
(4)
(5)
(8)
1. External sync input (genlock) BNC
2. 20 mA output for connection to receiver (ZR3M, ZR4M, ZR-DC)
3. Low-voltage power supply terminals (12 VDC/24 VAC)
4. Composite video output BNC
5. S-VHS video output connector
6. Power LED
7. Video iris lens connector
8. AC power supply cable
9. Joystick (under side flap)
10. DD Lens connector
11. Back-focus adjustment screws
12. 1/4-20 UNC mounting bush (fitted
at top and bottom)
7
Installation Instructions CDR Series
POWER SUPPLY CONNECTION
CDR2235, CDR3225, CDR4235 and CDR5225 (98 - 260 V AC 50Hz)
These cameras are fitted with a non-detachable power supply cord. REFER TO THE WIRING
INSTRUCTION LABEL ATTACHED TO THE SUPPLY CORD and terminate the cord with
the appropriate circuit. THESE CAMERAS MUST BE CONNECTED TO A PROTECTIVE
EARTH. Ensure that a secure means of isolation from the AC supply is provided for the
camera in accordance with the national and local wiring regulations/codes of the country of
installation. The green POWER LED on the rear panel indicates when power is connected.
CDR2233, CDR3223, CDR4233 and CDR5223 (11-40V DC; 12- 30V AC)
These cameras are fitted with a power supply that operates between 11-40V DC and 12-
30V AC. Connections and polarity are indicated adjacent to the terminals on the rear panel.
The power supply must be a class 2 isolated type. The green POWER LED on the rear
panel indicates when power is connected.
VIDEO CONNECTIONS
Composite Video
To obtain a video output connect a video coaxial-cable terminated by a 75 Ohm BNC
connector to the BNC socket marked VIDEO OUT on the rear of the camera.
S-VHS
An S-VHS video output is provided giving a Y/C separated video signal. The 4-pin mini-DIN
connector has the following specification: Y=1V pk-pk, 75 Ohm; C=0.3V, 75 Ohm
Genlock (external synchronisation)
For external synchronisation, connect a video coaxial cable, terminated with a 75 Ohm
BNC connector, to the socket marked GENLOCK on the rear of the camera. The GENLOCK
facility synchronises to either a 1V pk-pk video signal or a standard sync plus blanking
signal. A signal connected to the GENLOCK input automatically overrides all other
synchronisation settings.
Note
When using a master signal to synchronise multiple cameras, only one of the cameras
should have the genlock termination switched on, all the other cameras should have it
switched off. See SYNC MENU page 20.
LENS CONNECTION
Fixed and Manual Iris Lenses (for indoor use only) require no wiring connections.
Auto-Iris Lenses
Connections for auto-iris lenses are located on the rear of the camera. Connect auto-iris
lenses to the 3 terminal connector according to the diagram below.
+V
= Lens positive supply
= Lens ground
= Video drive signal
+
V
Auto-Iris Lens Connections
8
CDR Series Installation Instructions
LENS CONNECTION
Direct-Drive
Connect DD lenses to the female 4 pin socket on the side of the camera. If the lens does not
have a DD plug fitted then wire the lens to a suitable plug in accordance with the diagram
below.
1 = Damp -
2 = Damp
+
3 = Drive +
4 = Drive -
13
24
DD Lens
C
onnector
LENS SELECTION
Suitable lens types are C or CS mount in fixed-iris, manual-iris, auto-iris or direct-drive
versions. Sizes are shown below. Cameras are factory set for CS mount lenses. If using a
C mount lens, rotate either of the back focus screws approximately 30 turns anticlockwise
before fitting the lens.
FOCUS ADJUSTMENT
The back focus adjustment screws are located on the top and side of the case at the front
of the camera and should be adjusted using an appropriate screwdriver. Do not over turn
the back focus mechanism.
Fixed Lenses
Set the lens focus to infinity and view an image greater than 2 metres away. Focus the
image using the back-focus screw. Set the lens focus as required.
Manual Iris Lenses
Open the iris fully and set the lens focus to infinity. View an image greater than 2 metres
away. Focus the image using the back-focus screw. Set the lens focus and iris as required.
Auto-Iris and Direct-Drive Lenses
Fully open the iris by covering the lens with a suitable neutral density (ND) filter. Set the lens
focus to infinity. View an image greater than 2 metres away. Focus the image using the
back-focus screw. Remove the ND filter and set the lens focus as required.
Zoom Lenses
Set the lens focus to infinity and fully open the iris by covering the lens with a suitable
neutral density (ND) filter. Zoom out to the widest field of vision and view a distant object.
Adjust the back focus screw until the object is in focus. Next, zoom fully in and adjust the
focus of the lens until the object is again focused. Repeat these steps until the full zoom
range may be viewed with the minimum loss of focus.
Lens size
1/3"
1/2"
2/3"
1"
CDR2233
CDR4233
CDR2235
CDR4235
CDR3223
CDR5223
CDR3225
CDR5225
9
Installation Instructions CDR Series
SYSTEM CONNECTIONS
CDR series cameras receive coaxial telemetry via the Video Out BNC connector. These
telemetry signals are passed to a receiver when required via a 20mAtwisted pair connection.
In normal operation, the camera is completely transparent to telemetry commands and
simply forwards them to the receiver. However, when the cameras menu system is being
accessed, telemetry commands are no longer passed to the receiver and are instead used
to issue program instructions to the camera. The camera can be connected in a variety of
options as shown below:
Camera
Camera
Camera
P/T Head
Monitor
Monitor
Simple direct connection
Connection via telemetry controller
Connection with controller,
receiver and
p
an/tilt head
Telemetry Controller
Receiver
video
video
video
telemetry
telemetry
20mA T.P.
Telemetry Controller
The camera is connected directly to the
monitor. Camera setup must be made via
the built-in joystick.
The camera is connected to the monitor
via a telemetry controller (e.g. ZTX3).
Camera setup can be made via the built-
in joystick or remotely using the telemetry
controller.
This system comprises a telemetry
controller, receiver and pan/tilt head. The
camera is connected to the monitor via a
telemetry controller (e.g. ZTX3). The
receiver is connected to the camera via
a 20mA twisted pair connector. The
receiver controls the pan/tilt head
conventionally using telemetry
commands issued by the telemetry
controller. Camera setup can be made
via the built-in joystick or remotely using
the telemetry controller.
Notes
When using DC continuous rotation Pan/Tilt heads, two slip rings will be required for the
20mA twisted pair connection.
Use Belden 8723 or similar for the twisted pair cable. The screen must be earthed.
The recommended coaxial cable is RG59, copper cored. Maximum length is 500m.
10
CDR Series Installation Instructions
MENU SYSTEM
CDR series cameras utilise a menu system to facilitate setup and adjustment. The menu
system is password protected by means of a four digit number to prevent unauthorised
tampering and has two levels Basic and Advanced. The password scheme provides access
to one or both of these levels. The top level menu hierarchy is shown below.
ENTERING THE MENU SYSTEM
Entering the password
To enter the menu system, a password providing access to the Basic menu or the Advanced
menu must be input by the user. Note that entering a password to access the Advanced
menu will automatically provide access to the Basic menu. The manner in which the password
is entered depends on whether the camera is being controlled remotely or locally using the
built-in joystick.
1. Local: Press the joystick inwards, or,
Remote: Press the Autopan key 4 times in quick succession (i.e. within 2 seconds)
2. The screen shown below will appear:
Note that the first digit of the password is selected. To enter the password, the up/down
arrow keys or joystick are used to select the required number for each of the four digits in
the password. An up/down movement of the arrow keys or joystick will cause the selected
digit to either increment or decrement. When the digit is correct, use the left/right arrow keys
or joystick to move to the next digit of the password. When all four numbers have been
PASSWORD
ADVAN
C
ED MEN
U
*
BA
S
I
C
MEN
U S
AVE
&
EXI
T
RE
S
T
O
RE
S
ETTIN
GS
* depends on password
PASSWORD ENTRY
* * * *
USE ARROW KEYS
PRESS SELECT WHEN DONE
Autres manuels pour CDR Series
1
Autres manuels Baxall Caméra de sécurité
