Baumer VCXG.I r IP65/67 HA Manuel utilisateur
EN-US
Operating Manual
V1.2 | 14/03/2022 | 11700928
Camera Housing Sets
2V1.2 | 14/03/2022 | 11700928
Table of Contents
1. General Information ................................................................................................. 3
2. General Safety Instructions..................................................................................... 5
3. Housing Set Models ................................................................................................. 6
3.1 Housing Base Set A VCXG.I r IP65/67 HA.............................................................. 6
3.1.1 Environmental Requirements ........................................................................... 9
3.1.2 Tube assembly ................................................................................................. 9
3.2 Housing Base Set B V4A VCXG.I r IP69K .............................................................11
3.2.1 Environmental Requirements ......................................................................... 13
3.2.2 Clamp elements assembly ............................................................................. 14
3.2.3 Cable gland .................................................................................................... 17
3.2.4 Rear wall assembly ........................................................................................ 19
3.2.5 Tube assembly ............................................................................................... 22
3.2.6 Approved cables............................................................................................. 23
3.3 Housing Base Set C V4A VCXG.I r IP65/67 ......................................................... 24
3.3.1 Environmental Requirements ......................................................................... 28
3.3.2 Tube assembly ............................................................................................... 29
4. IP rating and chemical resistance ........................................................................ 30
4.1 IP Protection Classes (EN 60529) ........................................................................ 30
4.2 Chemical resistance of sealing materials.............................................................. 31
4.2.1 EPDM, TPE .................................................................................................... 31
4.2.2 Flouroprene®XP............................................................................................. 32
4.2.3 Acrylic glass.................................................................................................... 33
4.2.3.1 Alcohols, mono- and polyhydric................................................................ 33
4.2.3.2 Organic solvents, fuels ............................................................................. 34
4.2.3.3 Acids (organic and inorganic) ................................................................... 36
4.2.3.4 Leach........................................................................................................ 37
4.2.3.5 Salts, inorganic and organic (saturated solutions).................................... 38
4.2.3.6 Inorganic compounds ............................................................................... 40
4.2.3.7 Organic compounds ................................................................................. 40
5. Cleaning .................................................................................................................. 41
5.1 Cleaning and care of acrylic glass (Tube M60 / M62)........................................... 41
3
V1.2 | 14/03/2022 | 11700928
1. General Information
Thanks for purchasing a product of the Baumer family. This user´s guide explains how to
install cameras in a enclosure to protect your vision system and achieve IP 69 K protec-
tion.
Read this manual carefully and observe the notes and safety instructions!
Support
In case of any questions please contact our Technical & Application Support Center.
Worlwide: Baumer Optronic GmbH
Badstrasse 30
DE-01454 Radeberg, Germany
Tel: +49 (0)3528 4386 845
Website: www.baumer.com
E-mail: support.cameras@baumer.com
Target group for this User´s Guide
This user's guide is aimed at experienced users, which want to integrate camera(s) into
an enclosure.
Intended Use
The enclosure is used to protect a built-in camera in a production environment. Once the
camera is mounted in an enclosure, it can be easily adjusted and robustly installed on the
machine.
Notice
Use the enclosure only for its intended purpose!
For any use that is not described in the technical documentation poses dangers and will
void the warranty. The risk has to be borne solely by the unit´s owner.
Classication of the safety instructions
In the user´s guide, the safety instructions are classied as follows:
Notice
Gives helpful notes on operation or other general recommendations.
Caution!
Pictogram
Indicates a possibly dangerous situation. If the situation is not avoided, slight
or minor injury could result or the device may be damaged.
4V1.2 | 14/03/2022 | 11700928
Disposal
Dispose of outdated products with electrical or electronic circuits, not in the
normal domestic waste, but rather according to your national law and the
directives 2002/96/EC and 2006/66/EC for recycling within the competent
collectors.
Through the proper disposal of obsolete equipment will help to save valu-
able resources and prevent possible adverse effects on human health and
the environment.
The return of the packaging to the material cycle helps conserve raw mate-
rials an reduces the production of waste. When no longer required, dispose
of the packaging materials in accordance with the local regulations in force.
Keep the original packaging during the warranty period in order to be able
to pack the device properly in the event of a warranty claim.
Warranty Notes
If it is obvious that the device is / was reworked or repaired by other than Baumer techni-
cians, Baumer Optronic will not take any responsibility for the subsequent performance
and quality of the device!
Copyright
Any duplication or reprinting of this documentation, in whole or in part, and the reproduc-
tion of the illustrations even in modied form is permitted only with the written approval of
Baumer. The information in this document is subject to change without notice.
5
V1.2 | 14/03/2022 | 11700928
2. General Safety Instructions
Notice
Please observe the instructions and notes in the technical documentation of the camera
to be installed!
Caution
The suitability of the product for the users application with its specic condi-
tions of practice has to be tested and guaranteed by the user himself.
For special applications, please contact us in writing. We reserve the right to
make technical changes.
Caution
IP
Protection
Please follow these assembly guidelines carefully when assembling the en-
closures, as the IP protection rating stated may otherwise not be reached!
Caution
Inappropriate handling of the enclosure or any parts thereof may lead to a
leaky enclosure and may cause damage to the enclosed camera. Baumer
can take no liability for damages caused by improper handling.
Caution
The enclosures have been designed for a typical machine vision applica-
tion where the camera set-up is done once in order to build an application.
Frequent disassembly of the enclosure requires all seals and gaskets to be
renewed. Please order replacement seals or O-rings from Baumer when dis-
assembling the enclosure.
Caution
Baumer uses the best possible sealing materials for typical applications.
However every application is different - please check if our sealing material is
durable under the use intended.
Caution
Do not assemble the enclosure if any parts are damaged – this counts es-
pecially for the seals and sealing anges of the enclosure! In doubt – please
contact Baumer for advice.
Caution
Tighten the tube / rear wall as far as possible and don't use excessive force
in case it is not possible to screw the tube / rear wall completely down to the
metal middle housing part.
6V1.2 | 14/03/2022 | 11700928
3. Housing Set Models
3.1 Housing Base Set A VCXG.I r IP65/67 HA
▪Hard anodized cylindric housing corpus for VCXG.I (.XT) cameras for modular hous-
ing to meet Parma and Food & Beverage applications requirements
▪optional tube extension with Tube Module 6 mm (11185376), Tube Module 12 mm
(11185375) or Tube Module 36 mm (11198906).
▪thread: M62
▪length 56 mm
Optional (not included)
Mounting Tool (Art. No.: 11208719)
Tube Module (not included)
Housing Base Set A VCXG.I r IP65/67 H
A
6 mm (Art. No.: 11185376)
12 mm (Art. No.: 11185375)
36 mm (Art. No.: 11198906)
Cover Glass: PMMA (Art. No.: 11185376)
Cover Glass: Glass (Art. No.: 11185375)
Tube M62 (not included)
Camera
(not included)
Camera Mounting
Plate
7
V1.2 | 14/03/2022 | 11700928
Dimensions
A
A
A-A
2 - M4/ 6
8
28
56
59,25
Ø 56
61,5
37 2
Tube Moduls
For the installation of longer lenses, Tube Moduls with different lengths are available.
Art. No.: 11185376
Art. No.:
11185375
57,0xM26
59
57,0xM26
Ø56
O-Ring
A
A
A-A
12
6
15
57,0xM26
59
57,0xM 26
Ø56
O-Ring
A
A
A-A
6
5
9
Ø
Ø
Art. No.:
11198906
57,0xM26
59
57,0xM26
Ø56
O-Ring
A
A
A-A
36
6
39
Ø
9
V1.2 | 14/03/2022 | 11700928
Assembly the seal in the housing
Pull off the backing lm from the seal.
Glue the seal in the housing as
shown.
3.1.1 Environmental Requirements
Operating temperature -40 °C (-40 °F) ... 70 °C (158 °F)
Humidity 10 % ... 90 % non condensing
3.1.2 Tube assembly
Optional Tool
Housing Mounting Tool
(Art. No.: 11208719)
10 V1.2 | 14/03/2022 | 11700928
After positioning the camera, mount
the Tube M62.
Check the sealing surfaces for pos-
sible damages and scratches.
Feed the mounting tool over the en-
closure lid at the round hole end.
Slide the tool over the lid in a way
that the it sits between the jaws of the
tool. Insert the enclosure completely
and straight into the tool in order to
avoid scratching the enclosure lid!
Tighten the lid rmly until no gaps are
visible at the seal.
Do not tighten the lid so tight that
the seal forms a bead and pro-
trudes over the housing!
Ce manuel convient aux modèles suivants
2
Table des matières
