BARRON Trace-Light RxA Manuel utilisateur

INSTALLATION INSTRUCTIONS

800.533.3948 • www.barronltg.com

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

When using electrical equipment, basic safety precautions should always be followed including the following:

• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.

• Installation and servicing of this equipment should be performed by qualified service personnel only.

• Ensure that the electrical wiring conforms to the National Electrical Code NEC® and local regulations if applicable.

• Do not mount near gas or electrical heaters.

• Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering by

unauthorized personnel.

• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

• Any modification or use of non-original components will void the warranty and product liability.

• Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS!

20070135 REV 4 - 02/19

R A

3.46in

6.96in

1.26in

Ø 0.55in

0.98in

0.55in

Arm Mount - Drilling pattern

Pole Mount Arm

1. Remove the side plate from the arm. Skip to step 3

if mounting onto the square pole.

2. Attach round pole mounting plate onto the arm.

3. Route the cord through the arm, attach the fixture and

then tighten bottom screws.

4. Slightly pull the wires to make sure the hole on the

arm is sealed with a silicon gasket.

5. Make wiring connections inside arm. Refer to the

Wiring section.

6. Replace side plate ensuring the gasket is seated

correctly and fasten with screws.

Fig. 1

Slip-fitter

1. Route the cord through the slip-fitter, attach the fixture,

then tighten the bottom screws.

2. Remove the cover and adjust the slip-fitter to the

desired angle.

3. Make wiring connections. Refer to the Wiring section.

4. Install the slip-fitter on the 2” (2 3/8” O.D.) pole and

secure it with screws.

Wall Mount

1. Remove the side plate by loosening the screws.

2. Secure the backplate to the arm with the screws

provided.

3. Mark the desired location using the metal template

provided and drill holes to secure the arm to the wall

with appropriate anchors (not provided).

4. Route the cord through the arm, attach the fixture and

then tighten bottom screws.

5. Make wiring connections inside arm. Refer to the

Wiring section.

6. Replace side plate ensuring the gasket is seated

correctly and fasten with screws.

Trunnion Mount

1. Route the cord through the trunnion mount, attach the

fixture, then tighten the bottom screws.

2. Mark the desired mounting location and drill holes to secure

the trunnion to the desired surface with appropriate anchors

(not provided).

3. Make wiring connections. Refer to the Wiring section.

Wiring

Make AC power connections as follows:

Black - Line

White - Neutral

Green/Yellow Green - Ground

Dimming leads available in the 150W, 200W and 300W

models. A shielded 5 conductor line cord is provided for

convenience of installation, but not connected to the driver's

dimming leads. Connections inside housing at the driver and

at control device to be made as follows:

Purple - DIM+

Gray - DIM-

Note: This fixture auto adjusts for voltages from 120-277V or 347-480V driver. Cap all unused leads to prevent shorting.

IMPORTANT: Weather-proof your outdoor installation, be sure to seal all holes in fixture housing. (Mounting, conduit,

plugs, sensors and photocontrols, etc.) with silicone sealant.

Fig. 3

INSTALLATION INSTRUCTIONS

800.533.3948 • www.barronltg.com

20070135 REV 4 - 02/19

R A

Fig. 2

2 3/8”O.D

Pole size

Table des matières

Autres manuels BARRON Luminaire

BARRON

BARRON Trace-Light LHB Manuel utilisateur

BARRON

BARRON Exitronix NXFX Series Manuel utilisateur

BARRON

BARRON Trace-Lite TL205 Manuel utilisateur

BARRON

BARRON Exitronix CP-EX Series Manuel utilisateur

BARRON

BARRON TRACE-LITE AXB Manuel utilisateur

BARRON

BARRON Exitronix NY900U Series Manuel utilisateur

BARRON

BARRON EXITRONIX VEX Series Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur