Barco RETRO DATA 2100LC Manuel utilisateur

R9001309

INSTALLATION MANUAL

RETRO DATA

2100LC

Date : 130298 Art. No : R5975968A

BARCO PROJECTION SYSTEMS

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, January 1998.

Trademarks are the rights of their respective owners.

BARCO nv/Projection Systems

Noordlaan 5

B-8520 Kuurne

Belgium

Tel : +32/56/368211

Fax : +32/56/351651

E-mail : [email protected]

Visit Barco on the web : http://www.barco.com

Printed in Belgium

Federal communication commission (FCC statement)

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Instructions to the user :

if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the

following measures :

- Re-orientation of the receiving antenna for the radio or television.

- Relocate the equipment with respect to the receiver.

- Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.

- Fasten cables connectors to the equipment by mounting screws.

Note :

The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022.

Contents

i-1

5975968A RETRO DATA 2100LC 130298

TABLE OF CONTENTS

UNPACKING & PROJECTOR DIMENSIONS .................................................................................................................................................... 1

Unpacking .................................................................................................................................................................................... 1-1

Contents of the shipping boxes .................................................................................................................................................. 1-1

Projector dimensions ................................................................................................................................................................... 1-2

INSTALLATION SET UP ................................................................................................................................................................................... 2

Attachment of the projector Lens ............................................................................................................................................... 2-1

Cabinet Assembly ....................................................................................................................................................................... 2-1

Attachment of the Side Profile .................................................................................................................................................... 2-2

Mirror Positioning ......................................................................................................................................................................... 2-2

Focusing the Lens ...................................................................................................................................................................... 2-2

POWER UP CONSIDERATIONS ........................................................................................................................................................................ 3

Preparing your power cord ........................................................................................................................................................ 3-1

AC power cord connection ........................................................................................................................................................ 3-1

Enabling/Disabling the password ............................................................................................................................................... 3-2

Removing the projector ......................................................................................................................................................... 3-2

How to enable or disable the password ............................................................................................................................. 3-5

How to change the password menu ................................................................................................................................... 3-6

Switching on ............................................................................................................................................................................... 3-7

Projector status LED ................................................................................................................................................................... 3-7

Switching to standby .................................................................................................................................................................. 3-7

Switching off ............................................................................................................................................................................... 3-7

Lamp life ...................................................................................................................................................................................... 3-8

Fuses .......................................................................................................................................................................................... 3-8

1-1

5975968A RETRO DATA 2100LC 130298

Unpacking and Projector Dimensions

Contents of the shipping boxes :

¯1-Installation Manual

¯1-Owner's Manual

¯1-Power cord with outlet plug type ANSI 73.11.

¯1-Remote Control Unit, plus one 9V battery.

¯1-Safety Manual

Take the lower projector cabinet and the upper mirror/screen cabinet

out of its shipping carton and carefully place them on a solid level floor.

Save the original shipping cartons and packing material, they will

come in handy if you ever need to ship your retro projector. For

maximum protection, repack your projector as it was originally

packed at the factory.

1UNPACKING & PROJECTOR DIMENSIONS

Unpacking

Contents of the shipping boxes

Dimensions

¯1-Retro projector upper cabinet, comprising of one mirror/

screen cabinet, and two side profiles with fixing screws. And

upper and lower cabinet attachment screws.

To open the banding around the carton, pull out the clip as shown:

¯1-Retro projector lower cabinet, containing one RBLD2100

projector, and one projector lens (the lens will be clamped

inside the lower cabinet for shipping.)

1-2 5975968A RETRO DATA 2100LC 130298

Unpacking and Projector Dimensions

Projector dimensions (mm/")

All measurements shown are in millimeters and inches.

MOUNTING POSITION

RBLD2100

PROJECTOR

RBLD2100

MIRROR

POSITION

1534mm

60.4" 1371.4mm

54.0" 1341.4mm

52.8"

1005mm

39.6"

17mm

0.7"

500mm

19.7" 1020mm

40.16"

CENTRE OF

GRAVITY

881mm

34.7" 746mm

29.4"

500mm

19.7" 1020mm

40.16"

941mm

37.0"

820mm

32.3"

1969mm

77.5"

CENTRE OF

GRAVITY

PROJECTOR WEIGHT : 144Kg

PROJECTOR SCREEN SIZE : 67"

Installation Set Up

2-1

5975968A RETRO DATA 2100LC 130298

2INSTALLATION SET UP

Cabinet Assembly

Attention : Avoid touching the screen while handling the screen

cabinet in order to avoid any damage of the screen surface. Also

exercise caution not to damage the projector lens when joining the

cabinets together.

Lift up the upper mirror cabinet and bring it down vertically onto

the projector lower cabinet.

Both centering pins on the mirror cabinet must match and lock

into the centering holes in the projector cabinet. Ensure also that the

fixing holes in the upper mirror cabinet align with the holes in the lower

projector cabinet.

Once the cabinets are in place, two cabinet attachment screws

are secured (in the fixing holes) from the rear side of the retro

projector. The third is secured by reaching through the lower cabinet

(rear side,) and securing through the far underside of the projection

hole opening. This will require some care in manoeuvring as the fixing

is recessed when the two cabinets are in place. Ensure each screw

is tightened fully by hand.

Attachment of the projector Lens

Cabinet Assembly

Attachment of the Side Profile

Mirror Positioning

Focusing the Lens

Attachment of the Projector Lens

The projector lens is clamped during transportation inside the lower

projector cabinet (lower left back side). Exercise care not to scratch

or damage the lens when installing.

To fix into position it is necessary to first unclamp the lens, by

undoing the clamping screw completely. Lift carefully out by first

pushing it slightly backwards (to clear the clamping hooks) and then

pivoting up the farside of the lens and lifting out.

Take the lens and place through the projection hole on top of the

lower cabinet. The threaded end goes through first. Keep a tight hold

of the lens and carefully lower, the lens and projector barrel will meet

and the two will screw together.

WARNING :ENSURE YOU HAVE REMOVED THE PROTECTIVE PACKING FOAM FROM INSIDE

THE P ROJECTOR BARREL FIRST.

Screw onto the projector barrel in the clockwise direction ensur-

ing good connection. The lens should screw in without resistance,

if any resistance is felt (the two screw threads are not aligned) then

untighten immediately and remove and try once more. Once proper

connection is made, screw in the lens approximately three quarters

of its length for focusing later.

CLAMPING

SCREW

PROJECTION

HOLE

PROJECTOR

LENS

PROJECTOR

LENS

CLAMPING

HOOKS

/(16

352-(&7,21

+2/(

352-(&725

%$55(/

&



&



),;,1*

+2/(6 &(17(5,1*

+2/(6

&(17(5,1*

3,16

RQXQGHUVLGH

Installation Set Up

2-2 5975968A RETRO DATA 2100LC 130298

Attachment of the side profiles

The side profiles are packed during transportation inside the mirror

cabinet (back side.)

The side profiles are to be attached to the forward front sides

of the upper cabinet.

To fix in position turn in the screws a little and slide the profile over

the screws, use the three screws provided for each profile.

Mirror Positioning

The Upper cabinet contains a mirror for reflecting and projecting the

projector image onto the screen. During shipping or storage the mirror

is pivoted into the upper cabinet, and locked by two hand tightable

screws.

To open up the mirror cabinet and locate into the operational

position it is necessary to remove the two locking screws and pull

out the mirror flap fully (as far as possible.)

While holding the flap fully open, lock in position using the same

locking nuts, but this time screw into the screw holes on the outer

sides of the cabinet.

Focusing can only be achieved through access at the rear of the

retro projector, while the projector is in its operational mode. A

projector internal screen pattern may be used to assist focusing

(see Service mode in owners manual.)

Firstly ensure that the outer Front Rotary Lens Ring (a) is

completely turned in the clockwise direction.

Loosen the Locking Fastener Ring (c) of the lens by turning

counter clockwise a sufficient amount to allow turning of the Main

Lens Barrel Tube (b).

Focus the middle region of the screen by turning the Main Lens

Barrel Tube in the clockwise or anti clockwise direction until the

picture is focused. Attention: Do not turn out the lens to far,

otherwise it will fall out of the lens holder. Once the barrel is in the

desired position, lock the Fastener Ring (c) by turning clockwise

until fully locked.

It is now necessary to focus the corners of the picture by

adjusting the Front Rotary Lens Ring (a), moving the desired amount

in the anti clockwise direction.

0,5525

23(5$7,1*

326,7,21

)

0,5525

6+,33,1*

6725$*(

326,7,21

)

Focusing the Lens

Projector

(b) Main Lens Barrel Tube

(a) Front Rotary Lens Ring

 

LOCKING

SCREWS

LOCKING

SCREWS

3-1

5975968A RETRO DATA 2100LC 130298

Power Up Considerations

POWER UP CONSIDERATIONS

AC Power (mains) Cord Connection

Warning !

Verify the power voltage corresponds to that of the wall outlet.

Art. No. R9001309 must be connected to a 120V AC power source.

The projector input voltage is adjusted to 120V AC on leaving the

factory

Use the delivered power cord to connect your projector to the wall

outlet. Plug the female power connector into the male connector at

the rear of the retro projector.

The power voltage for the projector is indicated on the identification

plate on the rear of the projector.

This projector may be connected to an IT-power system.

Preparing your power cord

Mains power cord with an ANSI 73.11 plug

The wires of the delivered mains lead (power cord) are colored in

accordance with the following code :

Yellow and Green : ground (earth)

White : neutral

Black : live

POWER / M

9

Power cord connection

ART No-R9001309

V-120V

I-10Amp

Freq -60Hz

Ensure that the power switch is in the 'on-1' position on the rear

control panel and also ensure the internal mains power plug is in

place. The projector will not activate unless these two conditions are

correctly undertaken.

$8',2287

$8',2,1& $8',2,1%

$8',2,1$

9,'(2

69,'(2

5*%+&9

/5 /5

+& +&

72/2&$/&2175 2/21/<

3257

3257

3257

3257

3257

56,1 56287 &2003257 &75/

hard wire remote

2KP:

/5

 

Internal mains connection

permanently connected

Internal power switch always to be

positioned in the

’1’

(

)

state

Preparing your power cord

AC Power (mains) cord connection

Enabling/Disabling the Password

Switching On

Projector Status LED

Switching To Stand-By / Off

Lamp Life

Fuses

3-2 5975968A RETRO DATA 2100LC 130298

Power Up Considerations

Attention

Follow the procedure as described below, it is recommended that a

qualified Barco technician performs the alteration of the password

function.

It will be necessary to remove the front, rightside and leftside

panelling, plus the associated strengthening supports of the lower

projector cabinet, by either loosening or removing their fixing nuts.

WARNING : Power down all devices and switch off, discon-

nect all the input/output connectors to the projector. Unplug

the power cord from the rear of the retro projector and lock

the retro projectors rear positioning wheels.

Removing the Projector

,a. The front panel needs to be removed and this is achieved by

firstly opening the front control panel and gaining access to the two

large locking screws on either side of the control panel. Unlock by

turning one half turn counter clockwise. The front panel can now be

released from its mountings by tilting forwards slightly, then lifting

upwards and outwards (the front control panel should remain in the

open position at all times.)

/()7



6,'(



3$1(/

)52173$1(/

)5217&21752/3$1(

6833257&5266%$5

6833257&52663/$7(

352-(&7256/,'(5$,/

21(,7+(56,'(2)352-(&725

5,*+7



6,'(



3$1(/

$8',2287 $8',2,1& $8',2,1% $8',2,1$

9,'(2

69,'(2

5*%+&9

/5 /5

+& +&

72/2&$/&21752/21/<

3257

3257

3257

3257

3257

2KP:

/5





',6&211(&7$//,1387287387

&211(&7256217+,63$1(/

813/8*32:(562&.(7

35(66





WHEEL

POSITION LOCK

'OFF'

WHEEL

POSITION LOCK

'ON'

PRESS

Disconnect

Power cord

POWER / M

9

a

FRONT

PANEL LOCKING

SCREWS



FRONT

PANEL

FRONT

CONTROL

PANEL

It is necessary to remove the projector from the lower cabinet to

perform the changing of the pass word function. Follow the procedure

for 'Removing the Projector' next.

Enabling/Disabling the Password

Tools Required

Phillips screw driver (PH0)

Flat Top Screw Driver

Wrench, Spanner (No- 7,8,10)

3-3

5975968A RETRO DATA 2100LC 130298

Power Up Considerations

a

PROJECTOR

RIGHTSIDE BRACKET

LOCKING SCREW

LEFTSIDE

PANEL FRONT

FIXING SCREWS



a

b. Once the front panel has been removed the internal projector

and loud speakers are visible. The right loud speaker is of significance

since, if it is chosen to remove the projector from the front direction,

then this speaker must also be removed first. This is done by removing

all four of its attachment nuts on the top and right pillars of the lower

cabinet structure.

b

PROJECTOR

RIGHT

SPEAKER

RIGHTSIDE

PANEL FIXING

SCREWS



LEFTSIDE

PANEL BACK

FIXING SCREWS

The rightside panel must next be removed. The rightside panel is

removed by loosening its attaching screws and then pivoting out-

wards the front edge of this panel a little, now pull the front edge out

to release it.

a. Once the right panel has been removed the projector rightside

bracket locking screw is visible. A mental note of this screws

location should be made as it will be required to be undone in stage

.

,a. The leftside panel is removed by removing all its fixing screws

both on the front and back. Once the screws are removed gently lever

evenly out of its position.

Autres manuels pour RETRO DATA 2100LC

Table des matières

Autres manuels Barco Projecteur

Barco

Barco DP-1200 Guide de l'utilisateur

Barco

Barco R9001310 Manuel utilisateur

Barco

Barco R9002120 Manuel utilisateur

Barco

Barco Galaxy NH-12 Manuel utilisateur

Barco

Barco R9000904 Manuel utilisateur

Barco

Barco OV-513 Manuel utilisateur

Barco

Barco R9001290 Manuel utilisateur

Barco

Barco R9001390 Manuel utilisateur

Barco

Barco R9002321 Manuel utilisateur

Barco

Barco FLM HD20 Manuel utilisateur

Barco

Barco FLM R22+ Manuel utilisateur

Barco

Barco HDQ--2K40 Guide de l'utilisateur

Barco

Barco R9002327 Manuel utilisateur

Barco

Barco SLM G10 Performer Manuel

Barco

Barco BARCOSLM R6 Manuel utilisateur

Barco

Barco Cine 8 Manuel utilisateur

Barco

Barco SIM 7Q Manuel utilisateur

Barco

Barco RETROGRAPHICS 808s Manuel utilisateur

Barco

Barco SLM R12 Plus Manuel utilisateur

Barco

Barco GRAPHICS 1209S Manuel utilisateur

Barco

Barco DP2K-12C Manuel utilisateur

Barco

Barco CINE 6 Manuel utilisateur

Barco

Barco R9000972 Manuel utilisateur

Barco

Barco CLM HD8 Manuel

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur