Barco R9698236 Manuel utilisateur
BARCOPROJECTIONSYSTEMS
R9698236
Date:22.11..2001
INSTALLATION MANUAL
3-D Polar/Optical Soft Edge Kit for Projector SLM Series
Art.No.:R5976401Rev:00
OSEM/3-D Kit
SLM Series
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, November 2001.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCOn.v./ProjectionSystems
Noordlaan5
B-8520Kuurne
Belgium
Tel:+32/56/368211
Fax:+32/56/351651
Visite Barco at the web : http://www.barco.com
Printedin Belgium
BARCO 3 Projection Systems
Description and Contents of the kit
Purpose of the
Kit
The kit is designed to be mounted on SLM projectors to support the polarizer and/or soft
edge glass in front of the lens.
Application of the
Kit
The 3D/OSEM kit allows the user to display 3D application using passive stereo
technology and/or optical soft edging which may be necessary in case of large
screen multiple channel projections.
To be continued on next page
Illustration of the
Kit
B
A
To find out which spares to use :
OSEM: R8.... number located as shown on the illustration below (A).
The number is hidden by the frame, refer to page 15 to see how to remove the
frame.
3D: The name of the polar is located as shown on the illustration below (B):
Contents of the
Kit
Depending on the kit ordered the following features may be included.
- Polarizer LEFT
- Polarizer RIGHT
-Optical Soft Edge Matching (OSEM) LEFT
-Optical Soft Edge Matching (OSEM)RIGHT
-Polarizer LEFT+Optical Soft Edge Matching (OSEM) LEFT
-Polarizer RIGHT +Optical Soft Edge Matching (OSEM) RIGHT
-Custom OSEM
R8 - - - - - - -
3D FRONT R
3D FRONT RC
3D FRONT L
3D FRONT LC
BARCO 4 Projection Systems
B358674
R816851
G115520
R312010
R366242
R819615
V3673796
R312010
R366243
R823626
RV3620756
V3673796
B361138
R823625
B361138 B361138
Back view polar holder
Front view polar holderl
Holder fixation bars:
Description and Contents of the kit (Continued)
Spare List
To be continued on next page
fixation screws: R3631649
BARCO 5 Projection Systems
Some adjustment are more indicated in one application than another.
For instance the horizontal fine adjustment is more indicated for OSEM where it lines up
the soft edge and the edge of the image, whereas it becomes superfluous for polarizer
setup where the aim is to adjust roughly the image on the polarizer.
Each chapter mentions where the adjustment is recommended.
Table below gives an overview of the adjustments.
I: adjustment is required
0: adjustment is not required
Remark on the
adjustments
Description and Contents of the kit (Continued)
Adjustment Polarizer set up OSEM OSEM + Polarizer
Holder dist adj
Hor shift adj
Vertical adj
Hor fine adj
Tilt
Application
WRRVPDOO
WRRELJ
p9
p10
p11
p12
p13
Page
II
II I
0
II I
I
II
I
I
0
BARCO 6 Projection Systems
Mounting the fixation bars
What has to be
done
Two fixation bars have to be mounted on the projector frame.
Necessary Tools M6 spanner (n° 10)
To be continued on next page
Mounting the
fixation bars
To mount the bars, follow the next procedure:
1
2
3
4
5
6
1
2
3
3
3
4
Take the two bars to be mounted
Check the distances between the nuts.
If the distances do not coincide at all, slide the nuts A to
reposition them.
Put one of the the bars into the housing of the frame B
and push until the nut C is lined up with the farrest hole D
in the housing. Pull the housing plate a little upwards if the
insertion of the bar turns out to be difficult.
Insert and tighten one of the delivered bolts in the hole D
Dont tighten the bolts too hard because a horizontal
adjustment of the polarizer may be necessary afterwards.
Do the same for the nut E. If the nut is not in front of the
hole, slide the bar to line up the nut and the hole.
Try to obtain an outcoming distance as shown on image 4
Follow the same procedure for the other bar
Step Action Image
Illustrations
Image 1
26 23
123
Image 2
A
BARCO 7 Projection Systems
250
AB
C
D
E
Mounting the fixation bars
Image 3
Image 4
Illustrations
BARCO 8 Projection Systems
Mounting the polarizer holder
What has to be
done
The polarizer holder has to be mounted on the bars.
Necessary Tools M6 spanner (n° 10)
Mounting the
holder
To mount the holder, follow the next procedure:
1
2
1
1
Place the holder on the fixation bars, the two holes must be
in front of the remaining nuts in the bars.
Tighten the bolts to secure the position.
Step Action Image
Illustrations
Image 1
BARCO 9 Projection Systems
Holder distance adjustment
What has to be
done
The distance between the holder and the lens has to be adjusted.
This adjustment is necessary for the image to cover the largest area on the polarizer.
Necessary Tools M6 spanner (n°10)
Distance adjust To perform the adjustment, follow the next procedure:
1
2
3
1
2
Loosen (if necessary) the 4 bolts.
Slide the holder to the desired position.
Secure the position by tightening the 4 bolts.
Step Action Image
Illustrations
Image 1
Adjustment for max. spot sizeonthepolarizer area
WRRVPDOO WRRELJ
Image 2
BARCO 10 Projection Systems
Horizontal Shift of the holder
What has to be
done
Horizontal shift adjustment of the polarholder.
This adjustment is necessary to center the image (lightbeam) on the polarizer.
Necessary Tools none
Horizontal shift To perform the horizontal shift, follow the next procedure:
1
2
3
1
2
Loosen the 3 bolts as shown on image 1.
Slide the polarholder horizontally to the desired position.
Secure the position by tightening the 3 bolts.
Step Action Image
Illustrations
Image 2
$GM+25SRVLWLRQRIWKHOLJKWVSRWRQWKHSRODUL]HU
Image 1
Autres manuels Barco Projecteur
Barco
Barco CADWall Manuel utilisateur
Barco
Barco ELM Series Manuel utilisateur
Barco
Barco FLM R22+ Manuel utilisateur
Barco
Barco R9002031 Manuel utilisateur
Barco
Barco CLM HD8 Manuel utilisateur
Barco
Barco CLM HD8 R9050130 Manuel utilisateur
Barco
Barco Galaxy NH-12 Manuel utilisateur
Barco
Barco R9850010 Manuel utilisateur
Barco
Barco MGP D5 Mode d’emploi
Barco
Barco NW-12 Manuel utilisateur
Barco
Barco R9002120 Manuel utilisateur
Barco
Barco RETROGRAPHICS 808s Manuel utilisateur
Barco
Barco DATA 708 Manuel utilisateur
Barco
Barco Wodan Manuel utilisateur
Barco
Barco Vision 708 Manuel utilisateur
Barco
Barco HDF-W30LP Manuel d'utilisation
Barco
Barco DP-1200 Manuel utilisateur
Barco
Barco CLM W6 Manuel utilisateur
Barco
Barco DP-1500 Manuel utilisateur
Barco
Barco CLM R10+ R90501001 Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
