Barco F90 series Manuel utilisateur
F90-series Quick Start Guide
Printed on FSC certied paper (www.fsc.org)
8
7
6
5
4
3
2
1
General
601-0383-01
LED status light
Adjustable feet.
Projector lens.
Lens holder.
IR receiver: For receiving remote control signals
LCD touchscreen panel.
Keypad: Used for local operations on the projector.
Connector panel: Control and communication interfaces for the projector.
Front USB and Triggerboard.
1
1
2
1
2
6
3
4
8
7
1
2
1
9
5
5
9
LED Status LightLED Status Light
Projector Main Components and interfaceProjector Main Components and interface
1
WARNING!
Class 1 Laser RG2 Product.
For North America, Class 3R up to TR 2.33
This Projector may become RG3.
Refer to user manual before operating
Do not stare into beam. This projector
has class 4 laser cluster. Do not attempt
to disassemble or modify this projector.
Red light indicates a failure.
Contact service representative.
1
F90-series Quick Start Guide
General
DMX: DMX512 Input
RS-232: 9- pin DB9 Connector
Sync: BNC Sync Port IN/OUT; Bidir mini-DIN
Trigger: 12VDC - 0,5A (6W)
DL-DVI-D: Dual DVI-I 1.0 (DVI_D Functionallity)
HDMI: Standard HDMI 2.0
HDBaseT: Standard RJ45 8P8C Connector
SDI: SDI connector with Barcolink Support
RC: XLR connector for wired remote
USB: Usb 2.0 type A, 4 pin
LAN: Standard RJ45 connector
DP: Standard Display port
123 4
9 8
5
7
6
10
2
KeypadKeypad
Control & communication connectionsControl & communication connections
1
2
3
4
5
6
7
8
9
LCD Screen. Displays the current projector status and source connections.
Navigation Panel. Navigation arrows (up, down, left, right). Confirm selection. ()
Turn On Screen Display (OSD) menu ON / OFF.
Power On/Standby
Undo action / Back to previous screen
Deactivate the OSD. Only critical warnings will be displayed.
Select input source. Menu appear on OSD or in LCD display. Use Navigation Panel to select and confirm
Open / Close lens shutter.
Activate test pattern. Menu appear on OSD or in LCD display. Use Navigation Panel to select and confirm.
Activate Lens Function. Use navigation keys to manage and confirm actions.
10
F90-series Quick Start Guide
AC
110-240V
Connect power
Press Power On Button
Installation ConditionsInstallation Conditions
Ventilation RequirementsVentilation Requirements
General
1
2
3
Content is distorted or color is not correctContent is distorted or color is not correct
1
2
Power up procedure
3
Review source information in the Status menu (LCD
screen or OSD) and verify that the source signal is
compatible.
Check length of source cables; try shorter cables.
Use test images to verify that the correct aspect ratio is
selected.
Reset color and display settings to factory settings.
Restart the projector. Let the unit cool down for at least
1 minute prior to restarting.
4
5
Power down procedure
1000 mm
500 mm
Ambient operating conditions:
Altitude 0 - 500 m: Altitude 0 - 500m:
Temperature: 10 - 40°C Temperature: 40 - 45°C
Humidity: 10-80% RH Humidity: 10-65% RH
Altitude 500 - 1500 m:
Temperature: 10 - 40°C
Humidity: 10-80% RH
Power requirements: 110 - 240 V, 50 - 60 Hz
Dimensions excl. lens: 737 x 577 x 296 mm (WxLxH)
Weight excl. lens: 44,5 kg
Warm exhaust!
Do not place
heat-sensitive
objects in this area.
CAUTION!
Plug in mains power cord
Press the power button
Press Power Button for 3 seconds.
Remove main power cord from the projector
1
2
Failure Indications - what to do
AC
110-240V
Pull out Connector
Press Power Button for 3 sec
ZM
ZOOM
ZM
FCS
FOCUS
FCS
SHUTTER
OP
LENS SHIFT
RGB
RGB
R1
OSD
OSD
R2
LCD
LCD
R3
PAT
PATTERN
R4
INPUT
INPUT
DEFAULT
DEFLT
ADDRESS
ADR MCR
CL
BACK
BACK
MACRO
*#
MENU
MENU
LASER
LASER
Light On/Off
Lens Shift
Shift lens position
Menu
Activate main menu
R1-R4
Not in use
Shutter OP + CL
Open + Close Mech. Shutter
Power
Toggle power.
Confirm power off.
Input
Select input source
Address
Not in use
Remote Control
REMOTE CONTROL WARNING
Laser radiation class II product.
Wavelength 670nm; maximum output 1mW.
Remote control complies with applicable
requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable
requirements of EN/IEC 60825-1/2007
Altitude 1500 - 3000 m:
Temperature: 10 - 35°C
Humidity: 10-80% RH
F90-series Quick Start Guide
1
2
3
Maintenance
Installing lens
1
2
3
2
4
1
4
5
3
Go to www.barco.com and select your product. All available
software and hardware downloads are filed under the Technical
Downloads tab.
Download and unzip the firmware .zip file. Extract and save the
<version>.fw file to a USB stick with FAT-file system. Use the
eject function on your PC to safely remove the device.
Insert the USB stick into the projector’s USB port.
Follow instructions on the LCD display.
CAUTION !
Do NOT turn off, power down, or remove mains power supply
to the projector when an upgrade is in progress.
NOTE !
Once initiated, the upgrade procedure can take up to 20
minutes to complete.
4
Software upgradeSoftware upgrade
When handling lens in or out, always close shutter, see keypad explanation. Press Shutter keypad, and verify that the shutter keypad turn in to red
illumination. This indicate that the shutter is off. When lens is installed, open shutter by pressing the shutter key. Shutter open state is verified
when the shutter key illuminates white.
Verify that the lens release lever is in it’s default position, at the far left of the slide, as illustrated
Remove the protective cap at the lens bayonet end
Align the lens so that the red marking on the bayonet end is facing upwards, and towards the red marking on the top of the projector cabinet.
Install the lens bayonet into the lens mount, and then slide it to the right. Check that the lever is firmly at the far right end of the slide before
removing your hand from the lens..
Push the lens release lever in, and slide to the far left position
Pull the lens straight out of the lens mount.
NOTE!! To prevent damage to the lens, and dust contamination in the projector light processor, always replace the lens bayonet cap, lens front cap
and projector lens cap immediately after removing the lens.
Lens Removal
When removing the lens, always close the shutter, see keypad explanation. Press Shutter
keypad, and verify that the shutter keypad turn in to red illumintation. This indicate that
the shutter is off. When lens is installed, open shutter by pressing the shutter key. Shutter
open state is verified when the shutter key illuminates white.
Autres manuels pour F90 series
2
Table des matières
Autres manuels Barco Projecteur
Barco
Barco PFWX-51B Manuel utilisateur
Barco
Barco XDM Manuel utilisateur
Barco
Barco CineVERSUM 110 Manuel utilisateur
Barco
Barco HDF W series Manuel utilisateur
Barco
Barco R9001330 Manuel utilisateur
Barco
Barco DP K-19B Series Manuel d'utilisation
Barco
Barco CineVERSUM 110 Feuille d'instructions
Barco
Barco OL-521 Manuel
Barco
Barco R9002250 Manuel utilisateur
Barco
Barco F70 Series Manuel utilisateur
Barco
Barco Thor Series Manuel utilisateur
Barco
Barco XDL-4K30 Manuel utilisateur
Barco
Barco NW-12 Manuel utilisateur
Barco
Barco R9000972 Manuel utilisateur
Barco
Barco GRAPHICS 9300 Manuel utilisateur
Barco
Barco HDX series Manuel utilisateur
Barco
Barco F22 Series Manuel utilisateur
Barco
Barco R9002120 Manuel utilisateur
Barco
Barco BARCOREALITY 8200TCR+ Manuel utilisateur
Barco
Barco R9001260 Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
