Barco MDSC-1119-2124 Manuel technique

Online User Guide

MDSC-1119-2124

(This page intentionally left blank.)

Where to get more information

Where to find more information

The following documentation is included with your system:

Document Location Information

Getting started

guide

Booklet in box Booklet describing how to

install and setup the display

Getting started

guide (PDF)

CD-ROM The same booklet in PDF for-

mat

Online user

guide (PDF)

CD-ROM User guide in PDF format,

describing how to use the on-

screen display menus and

functions

RS-232 manual

(PDF)

CD-ROM Manual describing the RS-232

protocol

On-screen display (OSD)

To use the OSD menu system:

1. When the display is on and the OSD is not on the screen, touch the

Enter soft touch key.

The front illumination is switched on for about 10 seconds.

2. To display the main menu, touch the Enter touch key while

the illumination is on.

The OSD main menu appears. Several menu items contain

submenus.

Figure 1: Main menu

Note: Some of the menu items described in this manual may not

be available on your display, depending on the selected video

input.

3. To scroll through the menu, use the navigation keys or .

The corresponding submenus are displayed automatically. The red

scroll bar indicates the active menu item.

4. To jump into a submenu while it is displayed, press the Enter

touch key.

The red scroll bar now appears in the submenu.

MDSC-1119

Input Selection

Adjustments

User Profile

More...

Exit

PiP

On-screen display (OSD)

5. To exit from a submenu, use the navigation keys or to

select EXIT. Next, press Enter .

If you exit from the Main Menu, you exit the OSD.

6. To change an adjustment value or setting, use the navigation

keys or to select the adjustment or setting. Next, press Enter

to go into edit mode. This is indicated by the scroll bar turning

gray and the adjustment bar turning red.

Use the navigation keys or to change the value. Use Enter

to confirm the change.

Changes are saved automatically when you exit from the OSD.

Tips:

While you are adjusting a value:

• Touch and at the same time to reset to the factory-default

value.

• Touch first and then while still holding to select the

minimum value.

• Touch first and then while still holding to select the

maximum value.

While navigating in the OSD submenus:

• When any non-adjustable or name change menu item is

selected, pressing the Enter key for a long time closes the

OSD while saving the changes.

When the display is in stand-by, touch and hold the Stand-by

soft touch key for about 2 seconds until the display switches on.

To switch the display back in stand-by, touch and hold the Stand-

by soft touch key until the display switches off.

Input selection

The MDSC-1119/MDSC-2124 can be equipped with numerous different

video inputs. The available inputs may depend on the customer’s

requirements.

Input selection can be done in 5 ways:

• Automatically, by means of the Source Scan system

• By assigning a source priority

• Quick input selection by using the general purpose switch.

• Quick input selection by using the navigation keys without

entering the OSD.

• Using the Input selection menu in the OSD.

These 5 possibilities are described more in detail below.

Source scan

Source scan is a system that automatically scans all video inputs in the

display until it detects a correct video signal at one of the inputs. When

that video signal disappears again, the source scan system

automatically starts again, looking for another video signal.

The source scan system can be enabled or disabled in the Setup menu.

Source priority

In the Setup menu you can give priority to an input source. If a priority

has been established, the display will automatically select this source if

a signal is present on this input. The priority input selection will overrule

the manual input selection. For more information, please refer to

“Setup” on page 24.

Input selection

Quick input selection

You can quickly select another video input as follows:

1. Make sure the OSD is not on the screen. If it is, exit the OSD.

2. Touch the navigation keys or . The illumination is switched on

and the current video input is displayed.

3. While the illumination is on, touch the navigation keys or to

select another video input.

The quick input selection feature can be enabled/disabled in the Setup

OSD menu.

General purpose switch

If switches are connected to the display GPIO connector, you can use

them to switch inputs quickly. For this purpose, the GPIO input function

must be enabled in the Setup menu.

Input selection

Input selection menu

In this OSD menu, select the desired video input source from the list of

input sources.

The possible inputs are:

Note: Some of the inputs that are built-in in the display may not be

visible in the source scan, quick input selection menu or input selection

Input Description

VGA Analog video on Sub-D15 connector

Grayscale Analog monochrome video signal connected to

the G BNC connector

RGBS Analog video signals connected to the BNC con-

nectors

S-Video1 S-video signal (separate Y/C) on SVHS connec-

tor

S-Video2 S-video signal (separate Y/C) on BNC connec-

tors: Y on connector G, C on connector B

YPrPb Component video (Yuv) signals on BNC: Y on

connector G, Pr on connector R, Pb on connec-

tor B

CVBS1 Composite video signals on BNC R connector

CVBS2 Composite video signals on BNC G connector

CVBS3 Composite video signals on BNC B connector

Standard & HD-SDI Standard & High-definition serial digital video

connector

DVI digital DVI digital signals on DVI connector

DVI optical 4-wire input

Test Pattern Allows to switch on the internal test pattern

generator

Input selection

menu. They may be disabled in the Setup menu. See Setup, on

page 24.

Note: It can be that some of the inputs listed above can not be enabled

for your specific display configuration. For an overview of the possible

configurations, consult the connectors paragraph of the Getting Started

Guide.

Alias names

You can add alias names to the available inputs to make it easier for the

user to know what video source is connected to which input. E.g., if an

endoscopic camera is connected to the S-Video1 input, you can add the

alias ‘Endoscope’ to the S-Video 1 input.

To enter an alias name:

1. Select the desired input in the Input Selection menu.

2. Press for a few seconds, until ********** is added to the menu

line.

3. Now use and to select the first character.

4. Use to go to the next character.

5. Repeat steps 3 and 4 to make the alias name.

6. Use to delete the last entered character (like backspace on a

computer keyboard).

7. When the alias name is completed, you must use until the last

* is cleared.

8. To cancel the text edit without saving, press and for 2

seconds.

The alias names will appear in the Input Selection, Source Priority and

Enable Inputs menus, but only in the Input Selection menu you can

define or change them.

Adjustments

Adjustments menu

In this menu you can perform a number of image adjustments.

Note: When picture-in-picture (PiP) is active, the adjustments

will affect the PiP1 video frame only. If you wish to adjust the

video signal in the PiP2 frame, toggle the PiP frames in the PiP

menu so that the signal from frame2 is displayed in frame1. Then

make the adjustments (the PiP2 frame disappears while in

Adjustment menu) and finally toggle the PiP frames again.

Item Description

Brightness Adjusts the image brightness. This means all lumi-

nance levels from black to white are adjusted.

Brightness and contrast are factory-adjusted to

obtain a maximum dynamic range.

Contrast Adjusts the image contrast. This means the black

level remains constant and the white levels are

adjusted, changing the luminance difference

between black and white.

Brightness and contrast are factory-adjusted to

obtain a maximum dynamic range.

Color Adjusts the color saturation.

Hue Adjusts the hue. Do not use the Hue adjustment to

change the image color temperature. The Hue

adjustment is applicable only to correct phase

errors in NTSC video sources. This is an adjustment

for advanced users.

For color temperature adjustment, refer to the

Advanced menu.

Table des matières

Autres manuels Barco Moniteur

Barco

Barco Nio systems Manuel utilisateur

Barco

Barco SP-20 Manuel utilisateur

Barco

Barco MDCC-4430 Manuel utilisateur

Barco

Barco RHDM-1701 Manuel utilisateur

Barco

Barco Coronis 3MP LED MDCG-3221 Manuel utilisateur

Barco

Barco Eonis MDRC-2222 WP Manuel utilisateur

Barco

Barco Coronis 3MP Manuel

Barco

Barco Coronis Fusion 10MP Manuel utilisateur

Barco

Barco TX-126 Manuel utilisateur

Barco

Barco E192HSA Manuel utilisateur

Barco

Barco Coronis 5MP Mammo Manuel utilisateur

Barco

Barco LCD 5521 V4 Manuel utilisateur

Barco

Barco MDRC-1219 (TS) Manuel utilisateur

Barco

Barco MFCD 3220 D Mode d’emploi

Barco

Barco OverView EVD-4621 Manuel du propriétaire

Barco

Barco Coronic Uniti Manuel utilisateur

Barco

Barco MDCC-4330 Manuel utilisateur

Barco

Barco ADP361 Manuel utilisateur

Barco

Barco Coronis Fusion 4MP Manuel utilisateur

Barco

Barco MDRC-1219 HB Manuel utilisateur

Barco

Barco MDSC-8255 MNA Manuel utilisateur

Barco

Barco ILite 6 XP Manuel utilisateur

Barco

Barco HDM 5049 PLUS Manuel utilisateur

Barco

Barco MDSC-2326 MNAH Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation