Baratza Esatto Manuel utilisateur
Operations Manual
Grind by Weight Accessory
™
ESATTOTM shown with
PrecisoTM Grinder
1
Operations manuals are available in the following languages at
www.baratza.com
English.pdf
Spanish.pdf
French.pdf
Introduction
The Baratza ESATTOTM is an accessory that is designed specically for
use with your Baratza Maestro PlusTM, VirtuosoTM or PrecisoTM. This inno-
vative addition to your grinder will allow you to grind precise dosages of
coffee using real-time weight-based control. With its easy assembly and
simple operation, you will be automatically dosing ground coffee to within
+ / - 0.1 gram repeatedly.
Table of Contents
Introduction ..........................................................................................
Overview and Controls ........................................................................
Safety Information....... ........................................................................
Assembly .............................................................................................
Operations and Programming .............................................................
Care and Cleaning ..............................................................................
Warranty and Service ...........................................................................
1
2
3
4
6
7
8
Grind by Weight Accessory
™
2
Parts Identication
Timer Knob
Retainer
Increase / Decrease
Weight / grams
Removable
Rear Casting
Grounds Bin
Weight Platform
Start / Stop / Tare Button
Weight Readout
Window
Weight Preset
Buttons (3)
™
3
Safety Information
Important Information
Please read the information be-
low very carefully. It contains
important tips for the use, safety,
maintenance and care of this ap-
pliance. Please keep these oper-
ating instructions for future refer-
ence.
Your new ESATTOTM is rated for ei-
ther 120 VAC or 230 VAC. Please
conrm the voltage of your ESAT-
TOTM on the nameplate attached
to the bottom of the unit. The 120
VAC ESATTOTM can be used from
100 to 130 VAC and the 230 VAC
ESATTOTM can be used from 200
to 240 VAC. Please insure your
supply voltage range matches the
nameplate voltage on your ESAT-
TOTM. Only clean the ESATTOTM
housing with a dry or slightly damp
cloth. Do not use this unit for any-
thing other than its intended use.
If you cannot remedy a malfunc-
tion, please visit the web at www.
baratza.com for assistance. Re-
pairs are to be performed only by
authorized service centers. An
improperly repaired ESATTOTM is
a source of risk to the user and
voids the warranty. Baratza will not
accept any liability for damage or
injury if the ESATTOTM is used other
than for its intended purpose or is
improperly operated or repaired. All
warranty claims will be void.
For Your Safety
Do not operate the ESATTOTM with a
damaged cord or plug, or if the ESAT-
TOTM malfunctions. Do not leave your
ESATTOTM unattended while turned
ON.
Caution
Unplug the ESATTOTM from the elec-
trical outlet before cleaning.
To unplug, grasp plug and remove
from the outlet - never pull on cord.
Keep your ESATTOTM out of the reach
of children. Do not immerse the
ESATTOTM, plug or cord in water or
any other liquid.
4
Assembly
1. Remove the grounds bin from
the unit and set aside.
2. Remove the single Phillips
head screw from the center rear of
the rear metal casting cover and
slide the rear casting rearward
1cm to remove it. (see photo #1).
3. You must remove the rub-
ber feet from the bottom of the
grinder. Use a pair of side cut-
ters or a butter knife to pry the feet
out. (See photo #2).
4. Coil as much of the cord into
the hole in the bottom of the
grinder, about 1/3 will t.
(see photo #3).
Photo #1
Photo #2
Photo #3
5
5. Remove the grounds bin from
the grinder and slide the grinder
carefully into the ESATTOTM from
the rear going forward until the
grinder ts tightly against the front
casting. (See photos #4 & #5).
6. Once the grinder is in place,
plug the grinder cord into the AC
receptacle inside the base of the
ESATTOTM , and coil the remain-
ing cord in the space under and
behind the grinder.
(see photo #6).
7. Slide the cast metal cover into
place from the rear, taking care
to see that the front “ngers” lock
into correct position.
(see photo #7).
8. Insert the Phillips screw into
the rear of the casting to secure
the casting in place.
Photo #4
Photo #5
Photo #6
Photo #7
6
9. Install the ESATTOTM timer knob
retainer by placing the slot over
the blade of the knob, rotate the
knob until the retainer is vertical,
then slide the retainer into the
hole in the base of the ESATTOTM.
The knob will then be held in the
ON position.
(See photo #9 & #10).
10. Plug in the ESATTOTM to an AC
supply.
Photo #9
Operation and
Programming
Start / Stop / Tare
To accurately weigh the coffee as
it grinds you must rst Tare, (zero
out) the weight of the grounds
bin. To do this place the EMPTY
grounds bin on the weight plat-
form, then press and hold the Tare
button until the display reads 00.0.
The ESATTOTM will now display
only the weight of the coffee as it
is ground.
Press the Start button to start the
grinder. It will stop automatically
stop when the pre-programmed
weight has been ground. If you
would like to Stop the grinder
sooner, press the button a second
time.
Up / Down Arrow
Press either of these buttons
to change the weight value in
Grams, displayed in the LCD
window
Programmable Dosage
Buttons 1 - 2 - 3
Each of these buttons can store
a programmable weight value.
Simply press the up or down ar-
row to select the number of grams
you desire, then press and hold
the button you want the displayed
weight stored to. When the display
Photo #10
7
blinks, release the selected but-
ton. Repeat for each of the three
buttons. The programmed weights
will remain stored in memory even
if the ESATTOTM is unplugged.
Repeatability and Accuracy
Accurate repeatability is the goal
with the ESATTOTM. With all grind-
ers, the output in grams/second
varies with the grind coarseness.
At ner settings (i.e Espresso) the
PrecisoTM (for example) will produce
about 1.6 g/sec and at French
Press it will produce 2.5 g/sec. The
beauty of real-time weight-based
grinding is that using a scale elimi-
nates almost all of this variability.
Care and Cleaning
If the weight display does not
count up properly when grinding
coffee, remove the grounds bin
and blow air under the weigh-
ing platform to clear any coffee
grounds from the narrow gap
under the platform. DO NOT use
any type of tool under the weigh-
ing platform.
The narrow gap under the
weighing platform MUST be
free of ground coffee.
8
Warranty and Service
Length of Warranty: One-year from date of purchase.
United States Warranty Information
425-641-1245. Baratza will deliver an identical or comparable replacement to
your door, free of charge, and arrange to have your “failed” unit returned to us.
When you receive your replacement, please use the carton and packing mate-
rial and the return shipping label supplied to return the “failed” unit to us. Also,
please include your name, address and telephone number.
International Warranty Information
Go to: www.baratza.com for international warranty information.
Proof of Purchase and Product Registration
You can register your ESATTOTM at www.baratza.com. Registration will enable us
to contact you in the unlikely event of a product safety notication and assist us
in complying with the provisions of the Consumer Product Safety Act. The serial
number is located on the bottom of the unit. Please keep your sales receipt that
shows the date of purchase and complete the following for your personal records:
Serial Number (located on bottom of the unit):
Date Purchased:
Store:
For repairs or parts contact
Baratza LLC
3923-120th Ave. S.E.
Bellevue, WA. 98006
425-641-1245
e-mail: support@baratza. com
Parts: www.baratza.com
9
Grinding Notes
Autres manuels pour Esatto
2
Table des matières
Autres manuels Baratza Moulin à café
Baratza
Baratza Preciso Manuel utilisateur
Baratza
Baratza SETTE 30 Manuel utilisateur
Baratza
Baratza SETTE 30 Manuel de la liste des pièces
Baratza
Baratza Vario+ Manuel utilisateur
Baratza
Baratza Virtuoso preciso Manuel utilisateur
Baratza
Baratza Vario+ Manuel utilisateur
Baratza
Baratza Vario Manuel utilisateur
Baratza
Baratza Maestro Guide d'installation et d'utilisation
Baratza
Baratza VARIO-W Manuel utilisateur
Baratza
Baratza sette 270 Manuel utilisateur
Baratza
Baratza Maestro Manuel utilisateur
Baratza
Baratza Vario Manuel utilisateur
Baratza
Baratza SETTE 270W Manuel utilisateur
Baratza
Baratza Preciso Manuel utilisateur
Baratza
Baratza Encore Manuel utilisateur
Baratza
Baratza Encore Guide d'installation
Baratza
Baratza SETTE 30 Manuel utilisateur
Baratza
Baratza Virtuoso Manuel utilisateur
Baratza
Baratza Forté Manuel utilisateur
Baratza
Baratza Vario W+ Manuel utilisateur
