BANGGOOD ES120 Manuel utilisateur

E S 1 2 0

I n s t r u c t i o n M a n u a l

V 1.0.3

Safety Statement

II. Product Introduction

III.Performance Parameters

IV. Surface and Sockets

V. Use Steps

VI. Parameter Setting

VII. Firmware Upgrade

VIII. FAQ

IX. Certification Marks

Contents

I. Safety Statememt

1. General Safety

Please use output of 5V power adapter for charging.

Do not operate under high humidity;

Do not operate in inflammable/explosive environment.

keep product surface clean & dry.

Please don’t operate ES120 when it’s wet or operate

it with wet hands,which will cause an electric shock.

When using ES120,the handle is constructed with

precision, dropping shall be avoided.

2. Liability Statement

Any damage of the product,or losses related to the product

damage,if it’s man-caused,or assumed to be man-caused,

the liability will belong to the user.

II. Product Introduction

ES120 is a STM32 processor-based mini smart

electric screwdriver. It is featured with OLED

display, Micro USB interface which serves as PC

connecting and charging. Compact size, simple

operation and easy to use. It can meet the essential

requirements of school experiment, home appliance

repair and electronic engineering.

III.Performance Parameters

Voltage: 3-5V

Operate time: 60 min

Charging time: 40 min

Unload speed: 170 RPM

Torque range: 2.5/20kgf.cm

Bit specification: 4mm hex socket

Charging mode: Micro USB 5V input

IV. Surface and Sockets

1. Button

2. OLED screen

3. Hex socket (size: 4mm)

4. Micro USB socket

①②

③

④

V. Use Steps

When the screwdriver is power off, short press the key

to enter stand-by interface.

Way of use: In Standby mode, hold ES120's button,

and:

1) When your wrist turns left (see Pic.1 and Pic.3), the

bit of ES120 will turn clockwise;

2) On the contrary, when your wrist turns right (see Pic.2

and Pic.4), the bit of ES120 will turn anti-clockwise.

Pic. 1 Pic. 2

Operation Instructions:

Pic. 3 Pic. 4

Wrist turn left

Bit rotation direction

Wrist turn right

Bit rotation direction

Bit rotation direction Bit rotation direction

Wrist turn left Wrist turn right

3.Keep the screwdriver still on stand-by interface and

hold the key for 0.5 second, the screwdriver will rotate

in the same direction as that of previous use.

Stand-by interface: Working interface:

VI. Parameter Setting

1. Manual setting

Press the key continuously thrice on stand-by interface

to enter setting mode, and long press the button or wait

for 1.5 seconds to quit the setting mode. There are five

torque shifts in setting mode:

Shift A adopts an automatic mode,

in which the rotation speed of

screwdriver increases with the

increase of rotation angle.

Shift 1 to 4 correspond four

torques, which decrease gradually.

●

4、ES120 will automatically turn off if kept still for 15

seconds.

2.Configuration file setting

When the screwdriver is power off, connect it to PC with

USB data cable, short press the key to activate the flash

disk; open config.txt file in the disk, and the contents are:

StartAngle=2 #(2~10)

Gear=4 #(0~4)

MotoTimeCont=0 #ReadOnly

Ver=1.1 #ReadOnly

StartAngle The angle that starts ES120. E.g. set as

“2”, ES120 will start working at a rotation

angle of 2 degree.

Gear Torque shifts, “0-4“ corresponds with “A-4”

MotoTimeCont

Motor service time, read only

Ver Version, read only

VII. Firmware Upgrade

1、Visit www.miniware.com.cn and download the latest

ES120 firmware to your PC

2、When the screwdriver is power off, connect it to PC

with USB data cable, and hold the key until “DFU3.44”

displays on screen to enter DFU mode, and a virtual disk

will appear on PC.

Parameters Paraphrase Range

2~10

0~4

Note: Settings will be applied to ES120 by saving.

VIII. FAQ

.Torque shift: when the torque reaches the highest

torque shift, the screwdriver will stop for 3 seconds before

working again, as to protect the screw and motor.

DFU & flash disk mode: it may enter the mode only if

you start the machine when the screwdriver is power

off and connected with USB data cable.

.Charging icon:

Fully charged icon:

When in low battery, a warning will appear on screen

and the screwdriver will be automatically powered off:

It is a normal phenomenon if a little oil stain exists on

surface of hexagon wrench socket.

3.Copy the hex firmware to root directory of the disk,

and when the suffix of firmware changes to .rdy,

disconnect USB data cable or press the key continuously

thrice to quit DFU mode and thus complete the firmware

upgrade.

9.2 Statement of Fulfilling FCC Standard

This device fulfills part 15 of the FCC regulations Device

must fulfill below 2 conditions:

(1) Device must not generate interference.

(2) Device must be able to resist any interferenceson it,

including interferences that could cause dangerous

manipulation.

9.3 Statement of Fulfilling CE Standard

This is a trademark of Europe Union.

This product with CE logo on it fulfills related Euro Union

laws and regulations.

IX. Certification Marks

9.1 Disposal

Do not dispose this product with domestic waste.

Handling and recycle: Disposal of the product shall be

manipulated according to laws and regulations in your

area.

Table des matières

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel