B&B Electronics 232XS5 Manuel utilisateur

232XS5-1005 Manual Cover Page

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Five Port Expandable Smart Switch

Model 232XS5

Document ation Number 232XS5-1005

pn#4087-r2

This product designed and manufactured in Ottawa, Illinois USA

of domestic and imported parts by

International Headquarters

B&B Electronics Mfg. Co. Inc.

707 Dayton Road -- P.O. Box 1040 -- Ottawa, IL 61350 USA

Phone 815-433-5100 -- General Fax 815-433-5105

www.bb-elec.com

Orders e-mail: [email protected] -- Fax 815-433-5104

Technical Support e-mail: [email protected] -- Fax 815-433-5104

European Headquarters

B&B Electronics

Westlink Commercial Park, Oranmore, Co. Galway, Ireland

Phone: +353 91-92444 -- Fax: +353 91-92445

www.bb-europe.com

1997 B&B Electronics -- Revised March 2005

2000 B&B Electronics . No part of this publication may be reproduced or transmitted in any form or by any

means, electronic or mechanical, including photography, recording, or any information storage and retrieval system

without written consent. Information in this manual is subject to change without notice, and does not represent a

commitment on the part of B&B Electronics.

B&B Electronics shall not be liable for incidental or consequential damages resulting from the furnishing,

performance, or use of this manual.

All brand names used in this manual are the registered trademarks of their respective owners. The use of

trademarks or other designations in this publication is for reference purposes only and does not constitute an

endorsement by the trademark holder.

232XS5-1005 Manual Table of Contents i

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

TABLE OF CONTENTS

Chapter 1: INTRODUCTION ..................................................1

Checklist....................................................................................2

Specifications ............................................................................2

Chapter 2: SETUP...................................................................3

Port Configuration .....................................................................4

Serial Data Configuration ..........................................................6

RS-485 Support.........................................................................6

Chapter 3: Smart Switch Operation .......................................7

Programming the Second Character .........................................8

Binary File Transfer...................................................................8

Smart Switch/Port Combiner Mode ...........................................9

Enhanced Timer Mode -- Timer Features ...............................10

Expansion Mode...................................................................... 13

Chapter 4: SOFTWARE .........................................................15

Introduction .............................................................................15

Installation ...............................................................................15

Setup.......................................................................................15

Default Values.........................................................................16

Selecting Ports ........................................................................ 16

Parameters..............................................................................16

Appendix A: ASCII Character Codes ................................ A-1

Appendix B: Cable Charts ................................................. B-1

Chart 1. IBM PC DB25 Connector to Master Port ................ B-1

Chart 2. IBM PC DB9 Connector to Master Port .................. B-1

Chart 3. Modem DB25 Connector to Master Port................. B-2

Chart 4. IBM PC DB25 Connector to Ports A - E (DTE) ....... B-2

Chart 5. IBM PC DB25 Connector to Ports A - E (DCE)....... B-3

Chart 6. IBM PC DB9 Connector to Ports A - E (DTE) ......... B-3

Chart 7. IBM PC DB9 Connector to Ports A - E (DCE)......... B-4

Chart 8. IBM PC DB25 Connector to Ports A - E (DCE)....... B-4

Chart 9. IBM PC DB9 Connector to Ports A - E (DCE)......... B-5

ii Table of Contents 232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

232XS5-1005 Manual 1

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Chapter 1: INTRODUCTION

The RS-232 Five Port Expandable Smart Switch, Model

232XS5, allows one RS-232 host device to connect to as many as

five RS-232 devices. The switch can be controlled in three different

ways. The first way is referred to as smart switch mode or code

activated switch mode. In this mode, the switch is controlled by

sending a programmable preamble code to the "Master" port of the

232XS5. The second way the switch can be controlled is referred to

as port combiner mode. In port combiner mode, a slave port can

gain access to the master port by asserting a handshake line. If

none of the slave ports have their handshake line asserted, the

switch can be controlled using the preamble code. The third way

the switch can be controlled is the expander mode in which up to

four switches can be cascaded together to form up to 17 slave

ports.

The master port can be configured as a DTE or DCE port by an

internal switch setting. If the master port is configured as a DTE

port, the five slave ports will become DCE ports. The 232XS5

supports the following signals: TD, RD, RTS, CTS, DSR, DTR and

DCD.

The 232XS5 has an enhanced timer mode which offers special

timer features. The timer features can be used to prevent slave

devices from receiving preamble commands, inadvertently switching

from binary/graphic file transfers, and inactive slave devices from

holding control of the master port.

The 232XS5 will work with baud rates from 1200 to 115.2K bps;

7 or 8 data bits; even, odd or no parity; and 1 or 2 stop bits (7,N,1 is

not allowed).

NOTE: The data format and rates mentioned are used to switch

the 232XS5. The communication between the devices can use

any format or data rate.

232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

There are five LED's on the 232XS5 to indicate which port is

connected to the master port. The master port has a DB-9S female

connector and the slave ports have DB-9P male connectors. The

232XS5 requires 12Vdc at 100ma. which is provided through a

2.5mm power jack.

Checklist

Examine the shipping carton and contents for physical damage.

If damage is found, file a claim with the shipper immediately.

The following equipment should be in the shipping carton:

1. RS-232 Smart Switch

2. Instruction Manual

3. Software

If any of the items above are not in the shipping carton contact

the shipper immediately.

Specifications

Model: 232XS5

Size: 3.0"w x 5.5"l x 1.0"h

Power: 12Vdc to 16Vdc @ 100ma

232XS5-1005 Manual 3

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Chapter 2: SETUP

The 232XS5 is set up using an eight-position dipswitch and a

three-position set of jumpers. This dipswitch is used to set the

communication format, port configuration and expansion switch

address. The jumpers are used to set the smart switch/port

combiner mode, to enable/disable the enhanced features and to

enable/disable Expander mode. To change the settings on the

switch, remove the power from the unit, and remove the screws (4)

from the bottom of the 232XS5. The dipswitch is located on the top

of the PC board (side with LED’s) and is labeled “SW1.” The other

dipswitch, labeled “SW2” is used to set the second character of the

preamble. After the switches and jumpers have been set to match

your requirements, you can put the unit back together. Table 1

shows the settings for dipswitch “SW1” and Table 2 shows the

mode settings for “JP6” jumpers.

* = FACTORY DEFAULT

Table 1. Communication & Port Setup

Dipswitch SW1

1 2 3 4 5 6 7 8

Setting

0 0 0 X X X X X 1200 Baud

1 0 0 X X X X X 2400 Baud

0 1 0 X X X X X 4800 Baud

1 1 0 X X X X X 9600 Baud *

0 0 1 X X X X X 19.2K Baud

1 0 1 X X X X X 38.4K Baud

0 1 1 X X X X X 57.6K Baud

1 1 1 X X X X X 115.2K Baud

X X X 0 X X X X 8 Data Bits *

X X X 1 X X X X 7 Data Bits

X X X X 0 X X X Parity Disabled *

X X X X 1 X X X Parity Enabled

X X X X X 0 0 X Expansion Address A *

X X X X X 1 0 X Expansion Address B

X X X X X 0 1 X Expansion Address C

X X X X X 1 1 X Expansion Address D

X X X X X X X 0 DCE master port *

X X X X X X X 1 DTE master port

0 = OFF 1 = ON X = DON'T CARE

232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Table 2. Mode Setup

On = Jumper Installed Off = Jumper Removed X = DON'T CARE

* = FACTORY DEFAULT

Port Configuration

In order to determine the proper port configuration of the 232XS5, it

is necessary to have a basic understanding of the terms DCE and DTE.

RS-232 was designed, using DB-25 connectors, for connecting a DTE

(Data Terminal Equipment) device to a DCE (Data Communication

Equipment) device. Each device will have inputs on pins that

correspond to outputs on the same pins of the other device. For

example, a DTE device will transmit data out on pin 2 (on a DB-25) and

a DCE device will receive data in on pin 2 (on a DB-25). IBM PCs and

serial printers are DTE devices, modems are DCE devices.

Originally the RS-232 standard specified only a 25 pin D-sub

connector. Since then, the use of a 9 pin D-Sub supporting only a

portion of the original RS-232 signals has been used extensively,

starting with the IBM PC and migrating into other peripherals. The

pinouts for this 9 pin connector have since become the EIA/TIA 574

standard. This standard specifies a DTE device that transmits on pin 3

and receives on pin 2, with the DCE having the opposite configuration.

If an IBM PC compatible (DTE device) is going to be connected to

the 232XS5 master port, the master port should be configured as a DCE

port. If a modem (DCE device) is going to be connected to the master

port, it should be configured as a DTE port.

The master port can be configured as a DCE port (data received on

pin 3) or a DTE port (data received on pin 2) by setting dipswitch “SW1”,

position 8. To configure the master port as a DCE port, move dipswitch

“SW1”, position 8, to the "OFF" position. When the master port is

configured as a DCE port, ports A, B, C, D & E will become DTE ports

(Refer to Table 3). To configure the master port as a DTE port move

dipswitch “SW1”, position 8, to the "ON" position. When the master port

is configured as a DTE port, ports A, B, C, D & E will become DCE ports

(Refer to Table 4). Always power down the smart switch when changing

switch settings.

Jumper JP6

A B C

Setting

ON X X Enhanced Disabled *

OFF X X Enhanced Enabled

X ON X Smart Switch *

X OFF ON Expansion

X X ON Combiner Disabled *

X ON OFF Combiner Enabled

232XS5-1005 Manual 5

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Table 4. DTE MASTER PORT CHART

The 232XS5 supports the following RS-232 signals: TD, RD,

SG, RTS, CTS, DCD, DSR and DTR.

NOTE: All other lines are not connected.

The Smart Switch selects port A as the default port at power up.

Table 3. DCE MASTER PORT CHART

Master Port

(DCE)

Signal

,B,C,D & E Port

(DTE)

Pin# Direction Description Pin# Direction

3 Input Transmit Data (TD) 3 Output

2 Output Receive Data (RD) 2 Input

7 Input Request to Send (RTS) 7 Output

8 Output Clear to Send (CTS) 8 Input

4 Input Data Terminal Ready (DTR) 4 Output

6 Output Data Set Ready (DSR) 6 Input

1 Output Data Carrier Detect (DCD) 1 Input

5 <-------> Signal Ground (SG) 5 <----->

Master Port

(DTE)

Signal

,B,C,D & E Port

(DCE)

Pin# Direction Description Pin# Direction

3 Output Transmit Data (TD) 3 Input

2 Input Receive Data (RD) 2 Output

7 Output Request to Send (RTS) 7 Input

8 Input Clear to Send (CTS) 8 Output

4 Output Data Terminal Ready (DTR) 4 Input

6 Input Data Set Ready (DSR) 6 Output

1 Input Data Carrier Detect (DCD) 1 Output

5 <-------> Signal Ground (SG) 5 <----->

232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Serial Data Configuration

In order for the host device that is connected to the master port

to select any of the five ports, the Smart Switch must be set to

match the host's communication format. Dipswitch “SW1” is used to

select the communication format of the Smart Switch. Switch

positions 1 through 3 select the baud rate. Switch position 4 selects

7 or 8 data bits. Switch position 5 determines if parity is enabled or

disabled.

NOTE: A data format of 7 data bits, no parity and one stop is

not allowed.

Switch position 8 selects the port configuration, see section

titled "Port Configuration". Refer to Table 1. Always power down

the smart switch when changing switch settings.

RS-485 Support

RS-485 support may be

provided by adding a Model

485SD9TB RS-232 to RS-485

converter or other recommended

device to the slave ports of the

232XS5.

Port power of about 30 mA may be applied through the DTR line

(Pin 4) of the slave ports with jumper JP1-JP5. Normally, the

jumpers are set to allow DTR to pass from the master port. To

enable port power on a slave port, move the jumper from the“OFF”

to “ON” position on the corresponding JP jumper. To allow DTR to

pass from the master port to the slave port, move jumper from “ON”

to “OFF” on the corresponding JP jumper. DTR can only pass

through when the port is selected and the jumper is set to the “OFF”

position on the corresponding slave port JP jumper.

Table 5. Port Power Jumpers

* = FACTORY DEFAULT

Jumper

JP1-5

Setting

“OFF” DTR passed *

“ON” Port Power

232XS5-1005 Manual 7

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Chapter 3: Smart Switch Operation

Smart Switch mode is selected when jumper “JP6-B” is ON

(installed). In Smart Switch mode, the 232XS5 is constantly looking

for the three character preamble code by monitoring the data that is

being received on the master port from the host device. The

232XS5 requires a three character preamble code to turn on and off

a port. The first character must be the ASCII escape character

(decimal 27). The second character is user programmable by

setting dipswitch “SW2”. “SW2” comes from the factory

programmed to the ASCII character STX (decimal 2). The third

character should be the ASCII upper case letters "A", "B", "C", "D"

or “E” (decimal 65, 66, 67, 68 or 69 respectively) to select those

ports. To turn off the selected port the third character should be the

ASCII EOT character (decimal 4). The ASCII characters and their

equivalent decimal values are listed in Appendix A.

Example:

To turn on port B you would send the three ASCII characters:

ESC STX B

If you were writing a program in BASIC to control the Smart

Switch you would form a string like this:

SWB$ = CHR$(27) + CHR$(2) + "B"

You could then send SWB$ to select port B. Similar strings

could be used for turning on the other ports. To turn off the ports

the string might look like this:

TOFF$ = CHR$(27) + CHR$(2) + CHR$(4)

When you are done with a port you can either select a new one

directly or turn off the selected port and then turn on the next one.

We recommend that you turn off the selected port before selecting

the next one. The turn off command consists of three characters

that are nonprinting (ESC STX EOT). If port A is selected and you

send the command to select port B, all three characters (ESC STX

B) will pass through the A port since it is still selected and the letter

B will show up on your port A device. For information on preventing

command codes from being received by slave devices, refer to the

Enhance Mode section.

NOTE: There is no delay through the Smart Switch and the

data is not buffered.

232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Programming the Second Character

The second character comes programmed as the ASCII STX

character (decimal 2). You can change this to any 8-bit character

you wish by reprogramming dipswitch “SW2”. “SW2” is an eight-

position switch with each position equal to a certain weight. Refer to

“Setup” for instructions on removing the cover to access “SW2”.

Table 6 shows the weight chart for “SW2”.

*Factory Default -- ASCII “STX” character

(decimal 2), SW2 position 2 is only one ON.

If you wish to use the letter "U" as the second character, which

has a decimal value of 85, you would turn on switches 1, 3, 5, and 7

(1 + 4 + 16 + 64 = 85). Caution should be used when selecting the

second character, so that by itself, or with the ESC character in front

of it, it is not a valid command to any of the devices on the port. For

instance, on some printers ESC @ is the reset command. If you

tried to use the @ symbol (decimal 64) for the second character you

could reset your printer every time the preamble code was sent.

Note also that if your communication configuration is set for 7 data

bits you cannot use the eighth bit of SW2. For a list of the ASCII

character codes and their decimal values, refer to Appendix A.

Binary File Transfer

A simple method of using the Smart Switch to transfer binary

files without the concern of it accidentally disconnecting, is to set the

file transfer at a baud rate different from the baud rate of the Smart

Switch. When transferring files at a different baud rate, the Smart

Switch will stay connected from the last preamble code.

Table 6. Programmable Character Setting

Dipswitch SW2* WEIGHT

1 1

2 2

3 4

4 8

5 16

6 32

7 64

8 128

232XS5-1005 Manual 9

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Smart Switch/Port Combiner Mode

With the 232XS5 set up with a DTE master port, this mode

allows Slave Ports A-E to select the master port using the RTS input

line. It also still allows selection from the master port via the

preamble code described in the Smart Switch Only Mode section.

Jumper “JP6-C” must be OFF (removed) to be in port combiner

mode. Port combiner mode is not accessible when the unit is set up

as a port expander, so JP6-B must be ON (installed). When RTS

goes high on any of the five slave ports, it will establish a connection

from that port to the master port. This works on first-come-first-

served basis. If multiple ports have their RTS lines high, the port

that has been waiting the longest will be next to be connected to the

master port. For example (initial conditions -- no slave ports with

RTS lines asserted.), in chronological order, Port C asserts its RTS

line, Port A asserts its RTS line, Port D asserts its RTS line and then

Port C disasserts its RTS line. When Port C asserts its RTS line, a

connection will be made between the master port and Port C. When

Port C disasserts its RTS line, Port C will be disconnected and Port

A will be connected to the master port. When Port A disasserts its

RTS, Port A will be disconnected and Port D will be connected to

the master port.

For example, port A is configured as a DTE port. In order to

establish a connection to the master port, port A must set RTS high

(assert). The 232XS5 would recognize this as a prompt for

connection to the master port. The connection would be dropped as

soon as RTS on port A is brought low. Ports B-E may raise RTS at

any time to request a connection. However, if port A is connected to

the master port, any data sent from the devices on ports B-E to the

232XS5 will be lost. The 232XS5 does not have any buffering.

Master

Port

Preamble code controls access to slave

ports if slave handshake line is not asserted

Slave

Port

Port Combiner Mode

Slave

Port

Slave

Port

Handshake line of any slave

port controls access to master po

Slave

Port

Slave

Port

232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

NOTE: When a port is selected via the Master Port, the RTS

lines will be ignored until the Master Port sends the turn off code.

When the Master Port is selected by RTS, all preamble codes

will be ignored. The port combiner function is not available with

the Master Port configured as a DCE or in expansion mode.

A typical application would be to have RTS and CTS tied

together on the master port. When RTS on port A is asserted, CTS

on port A will be asserted when a connection is established. If a

port is not connected to the master port, then CTS on that port will

remain low. Therefore, a port can monitor the handshake line to

determine if a connection has been established.

Enhanced Timer Mode -- Timer Features

The 232XS5 has an enhanced mode, which offers special timer

features. The timer features can be used to prevent slave devices

from receiving preamble commands, inadvertent switching from

binary/graphic file transfers, and inactive slave devices from holding

control of the master port. The timer has two different modes: an

inactivity mode and an inadvertent switch mode. When in inactivity

mode, the 232XS5 will monitor the data lines. If there is no activity

for the specified time, the selected slave port will be disconnected

from the master port. When in inadvertent switch mode, the

232XS5 will ignore switching commands for the specified period of

time. After this time has expired, the selected slave port will be

disconnected from the master port.

The timer functions are enabled via a jumper setting and

through software commands. Jumper JP6-A must be OFF

(removed) for the 232XS5 to be in enhanced mode. The

software commands follow the same format as preamble codes

used for switching. There are two commands that must be sent to

the 232XS5 to set the timer functions: Set Timer Value and Set

Timer Mode. These commands require an additional byte for data.

The Set Timer Value command requires the third byte to be an

ASCII “T” character. The data byte (fourth byte) must be a value

between ASCII “0” and ASCII “9”. A value of “0” is used to disable

the timer. The time set by the Set Timer Value command

determines the length of time the 232XS5 wll wait before

disconnecting an inactive port, or the length of time it will ignore

switching commands from the master. Refer to Table 7 for timer

values. For example, sending the following string to the 232XS5 will

set the timer value to 5 seconds (assuming programmable character

is the factory default of 2).

232XS5-1005 Manual 11

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

SetTV$ = CHR$(27) + CHR$(2) +”T” + “6”

The “T” tells the 232XS5 it is the set timer value command and the

“6” indicates which timer value to use.

Table 7 - Timer Values

The Set Timer Mode command tells the 232XS5 whether the

time set by the Set Timer Value command will be used to determine

the time-out of an inactive port, or the length of time switching

commands are ignored. The third byte of the Set Timer Mode

command is an ASCII “M”. If the data byte (fourth byte) is an ASCII

“0”, zero (default), the timer will be setup as an inactivity timer. For

example, sending the following string to the 232XS5 will set up the

timer as an inactivity timer (assuming programmable character is

the factory default of 2).

SetTM$ = CHR$(27) + CHR$(2) +”M” + “0”

The “M” tells the 232XS5 it is the set timer mode command and the

“0” indicates to set up the timer as an inactivity timer. When the

timer is configured as an inactivity timer, the 232XS5 will monitor the

data lines (TD & RD) for data. If there is no activity for the specified

timer value, the slave port that is connected to the master port will

be disconnected. In smart switch mode, the inactivity timer can be

used to prevent the preamble codes from being received by the

slave devices. In port combiner mode, the inactivity timer can be

used to prevent devices from tying up the master port. For example

(port combiner mode), all the slave ports have their handshake lines

asserted. The device on Port C has its handshake line asserted

and is currently connected to the master port, but has not been

transmitting or receiving data. When the inactivity timer expires,

Port C will be disconnected and the next slave port will then be

Data

Byte

Value

0 timer disabled

1 10ms

2 25ms

3 100ms

4 500ms

5 1 s

6 5 s

7 30 s

8 1 min.

9 5 min.

232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

connected to the master port (following the first-come-first-served

rule). Port C will then be placed at the “end of the line”.

If the data byte of the Set Timer Mode command is an ASCII

“1”, the timer will be setup to ignore switching commands. Sending

the following string to the 232XS5 will set up the timer to ignore

switching commands. (Assuming programmable character is the

factory default of 2).

SetTM$ = CHR$(27) + CHR$(2) +”M” + “1”

The “M” tells the 232XS5 it is the set timer mode command and the

“1” indicates to set up the timer to ignore switching commands.

When the timer is configured in this mode, the 232XS5 will not

accept any switching commands (“A”, ”B”, ”C”, ”D”, “E”, or “EOT”) for

the specified timer value. After the timer has expired, the slave port

that is connected to the master port will be disconnected. This

feature is useful to prevent inadvertent switching during

binary/graphic type file transfers. For example (smart switch mode),

the timer is configured to ignore switching commands for 5 seconds.

The select Port D command is sent to the 232XS5. Once Port D is

connected a file of unknown data type (so file may or may not

contain a switching command sequence) is to be transferred

through the 232XS5. For a period of 5 seconds after Port D is

connected, no switching commands will be accepted. As long as

the file transfer takes less than 5 seconds, there is no chance the

232XS5 will inadvertently switch ports.

Table 8 - 232XS5 Smart Switch Mode Commands

*X represents the programmable character set by dipswitch SW2

**NU = Not Used

Command Characters

Function 1st 2nd 3rd 4th Comments

Select Port A ESC X* “A” NU** Switching Command

Select Port B ESC X* “B” NU** Switching Command

Select Port C ESC X* “C” NU** Switching Command

Select Port D ESC X* “D” NU** Switching Command

Select Port E ESC X* “E” NU** Switching Command

Deselect Port ESC X* EOT NU** Switching Command

Set Timer Value ESC X* “T” “0”-”9” Enhanced Mode

Set Timer Mode ESC X* “M” “0”,”1” Enhanced Mode

232XS5-1005 Manual 13

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Expansion Mode

The number of serial ports on the 232XS5 can easily be

expanded to a maximum of seventeen ports. Up to four 232XS5

units may be cascaded in expander mode. Each unit address adds

four additional serial ports to the five on unit address “A”. Port C is

used as the expansion port that connects to the follow-on master-

port for switch units addressed “B” thru “D”. Expansion Switch unit

address “A” is the last Switch in the chain.

Expander mode is selected when jumper “JP6-B” is OFF

(removed.) In Expander mode, the 232XS5 is constantly looking for

a four character preamble code by monitoring the data that is being

received on the master port from the host device. The 232XS5

requires a four character preamble code to turn on and off a port.

The first character must be the ASCII escape character (decimal

27). The second character is user programmable by setting

dipswitch “SW2”. “SW2” comes from the factory programmed to the

ASCII character STX (decimal 2). The third character is the

Expansion Switch Unit Address character “A” through “D”. The

fourth character should be the ASCII upper case letters "A", "B", "C",

"D" or “E” (decimal 65, 66, 67, 68 or 69 respectively) to select those

ports. To turn off the selected port the third character should be the

ASCII EOT character (decimal 4). For instance, to turn on port B of

Expansion Switch unit address C, you would send:

ESC STX C B

If you were writing a program in BASIC to control the Smart

Switch you would form a string like this:

SWB$ = CHR$(27) + CHR$(2) + "C" + ”B”

Master

Port

Expansion

Port

17-Port Cascaded Expansion Mode

Address D

Address C

Slave

Port

Slave

Port

Slave

Port

Address B

Slave

Port

Slave

Port

Slave

Port

Slave

Port

Slave

Port

Slave

Port

Expansion

Port

Slave

Port

Slave

Port

Expansion

Port

Slave

Port

Slave

Port

Slave

Port Slave

Port

Address A

Slave

Port Slave

Port

232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

You could then send SWB$ to select port B of Expansion switch

unit address “C”. Similar strings could be used for turning on the

other ports. To turn off the ports the string might look like this:

TOFF$ = CHR$(27) + CHR$(2) + CHR$(4)

When you are done with a port you can either select a new one

directly or turn off the selected port and then turn on the next one.

For information on preventing command codes from being received

by slave devices, refer to the Enhanced Mode section.

Table 9 - 232XS5 Expander Mode Commands

* X represents the programmable character set by dipswitch SW2

** NU = Not Used

***Port C is used as the expansion port for unit addresses B thru D.

Command Characters

Function 1st 2nd 3rd 4th Comments

Select Port A ESC X* “A” “A” Address A

Select Port B ESC X* “A” “B” Address A

Select Port C ESC X* “A” “C”*** Address A

Select Port D ESC X* “A” “D” Address A

Select Port E ESC X* “A” “E” Address A

Select Port A ESC X* “B” “A” Address B

Select Port B ESC X* “B” “B” Address B

Select Port D ESC X* “B” “D” Address B

Select Port E ESC X* “B” “E” Address B

Select Port A ESC X* “C” “A” Address C

Select Port B ESC X* “C” “B” Address C

Select Port D ESC X* “C” “D” Address C

Select Port E ESC X* “C” “E” Address C

Select Port A ESC X* “D” “A” Address D

Select Port B ESC X* “D” “B” Address D

Select Port D ESC X* “D” “D” Address D

Select Port E ESC X* “D” “E” Address D

Deselect Port ESC X* EOT NU** Switching Command

Set Timer Value ESC X* “T” “0”-”9” Enhanced Mode

Set Timer Mode ESC X* “M” “0”,”1” Enhanced Mode

232XS5-1005 Manual 15

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Chapter 4: SOFTWARE

Introduction

The Smart Switch software allows the user to change Smart Switch ports

on three different modules (232XSS, 232XS5, PortMUX). The Smart Switch

software is designed as diagnostic software for the above modules. It will

allow you a Module by Module connection to the individual port.

Installation

The software for the Smart Switch is designed to be run in any Windows

environment. To install it on your hard drive follow these steps:

Method One

•Install the software media.

•Select Settings from the Start Button and click on Control Panel.

•In the Control Panel Window, double click on the Add/Remove

Programs.

•Click on the “Install” button.

•Follow the instructions of the setup program.

Method Two

•Install the software media.

•Select Programs from the Start Button and click on Windows Explorer.

•Click on the drive containing the software.

•Double click on the file “Setup.exe”.

•Follow the instructions of the setup program.

The following file will be located on your hard drive:

• SS.EXE - The executable file for the Smart Switch.

• FILES.LST Contains a list and description of files installed on your hard

drive.

• READ.ME Contains corrections and additions to the printed users

manual.

• HISTORY.LST Contains a historic description of the product.

Setup

The Smart Switch program will prompt the user for the Module that is in

use the first time that the software is run. After the proper Module (i.e.

PortMUX, 232XS5,etc.) is selected then a window specific to that Module will

appear and the user may personalize communication parameters as per

their specific needs. Comport, Baud Rate, and Data Bits (Character Mode,

and User Defined Character may also be set for 232XSS and 232XS5

Modules).

232XS5-1005 Manual

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104

B&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445

Should the user wish to change the Module choice to another there is a

Module menu choice with the three support Module types (PortMUX,

232XSS, and 232XS5). After changing the Module the user will be prompted

to restart the Smart Switch software to reset the connection.

Default Values

When you start Smart Switch software, the default values will be used.

The default values are:

Selecting Ports

To select a port the user need only pick from the Menu-> Comport the

comport to which the device is attached. The Smart Switch program

supports comports 1 through 6. If the port exists but does not have a smart

switch device attached, SS will not detect it. The SS software will only detect

invalid/undefined comports.

Parameters

The Port Address is the address where the serial communications port

is located. If this is unknown you can use the program PORTFIND.EXE

which is located in the provided software. To use PORTFIND.EXE:

If you installed the software on your hard drive see the Installation

section:

•Type C: and press the ENTER key.

•Type CD\SS\UTIL and press the ENTER key.

•Type PORTFIND and press the ENTER key.

The result will be similar to the following:

Slave 8259 present can't use shared IRQ2

COM1 at address 03F8h is set for IRQ4 and is a 8250A or 16450 type UART

COM2 at address 02F8h is set for IRQ3 and is a 8250A or 16450 type UART

LPT1 at address 0378h found

Some of the typical port addresses are as follows:

Description Default Value

Port Address COM 1

Baud Rate 9600

Data Bits 8 Data Bits

Second Character 2 = STX (CTRL B)

Autres manuels pour 232XS5

Table des matières

Autres manuels B&B Electronics Changer

B&B Electronics

B&B Electronics e-Linx EIRP610-2SFP-T Manuel utilisateur

B&B Electronics

B&B Electronics 485DSS Manuel utilisateur

B&B Electronics

B&B Electronics 232BSS4 Manuel utilisateur

B&B Electronics

B&B Electronics Elinx EIR510-2MC-T Manuel utilisateur

B&B Electronics

B&B Electronics ETHUB16 Manuel utilisateur

B&B Electronics

B&B Electronics 232XSSD4 Manuel utilisateur

B&B Electronics

B&B Electronics EIR610-3SFP-T Caractéristiques techniques

B&B Electronics

B&B Electronics Elinx EIR508-2MC-T Manuel utilisateur

B&B Electronics

B&B Electronics EIR505-xx Manuel utilisateur

B&B Electronics

B&B Electronics EIR618-2SFP-T Manuel utilisateur

B&B Electronics

B&B Electronics 485DSS Manuel utilisateur

B&B Electronics

B&B Electronics EIR405-SFP-T Manuel utilisateur

B&B Electronics

B&B Electronics 8 PORT SMART SWITCH CE 232D4SS8 Manuel utilisateur

B&B Electronics

B&B Electronics 232SS2 Manuel utilisateur

B&B Electronics

B&B Electronics 232XS5 Manuel utilisateur

B&B Electronics

B&B Electronics Elinx EIRHP305-T Manuel utilisateur

B&B Electronics

B&B Electronics UHR304 Manuel utilisateur

B&B Electronics

B&B Electronics ICE-104P Mode d'emploi

B&B Electronics

B&B Electronics 232BSS4 Manuel utilisateur

B&B Electronics

B&B Electronics Elinx EIRP305-T Manuel utilisateur

B&B Electronics

B&B Electronics Elinx EIRP410-2SFP-T Manuel utilisateur

B&B Electronics

B&B Electronics Elinx EIR418-2SFP-T Manuel utilisateur

B&B Electronics

B&B Electronics 232MSS2 Manuel utilisateur

B&B Electronics

B&B Electronics 232BSS4 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur