Bamo FS4 Manuel utilisateur
Top tank level indicator
Top tank level indicator
FS4
02-03-2015 584 M1 01 F
MES
584-01
IN TRUCTION MANUAL
Top kank level indicator
FS4
CAUTIONS
• Installing and operating the unit F 4 must be done outside of any magnetic field.
• Any iron device must be at least at 10 cm as a minimum.
• Use non magnetic connection (Brass, Stainless Steel or plastic).
• Verify the chemical compatibility between the fluid and F 4 materials.
• Pressure inside the tank and indicator, must be at 1 bar as a maximum or less.
PRINCIPLE
• This indicator allows a direct level reading, on time, on any liquid level (respecting chemical resistances) even when tank is opaque.
• Assembly is done above the tank. Float and index with magnet, are fixed on a stem.
• When indicator is on the tank, the float follows the liquid level increases, so does the index.
• Index with magnet can actuate one or more, B M 501 level switches.
• A graduated ruler (option) fit the indicator tube for a quantified reading.
02-03-2015
584 M0 01 F Page 2
MOUNTING
The indicator exceeds very widely the summit of the tank, it is necessary to make sure that there is enough space to take it up.
The indicator is linked to the tank by DN65 flange connection (F 4 model) or 2’’ threated connection (F 4 Fût model)
For contact adding or any option, please refer to owner’s manual of those device .The F 4 indicator is ready since its mounting
on the tank. The float follows level raising and the colored indicator shows level position on upper part of the device. To avoid
any overpressure which could prevent the float to go up, two little holes are located under the fixating flange.
MAINTENANCE
F 4 is a robust level indicator; it does not require specific maintenance. From time to time, clean the float and back face of tube.
TECHNICAL FEATURES
Float: PPH or PVC
tem: PPH or PVC
Guiding tube: PPH or PVC
Indicator: PPH/PVC or PVC
Temperature maxima PVC: 60 °C
PPH: 80 °C
Maximal pressure: Atmospheric
OPTION: Level switches B M 501
or BRK 60/32
Standard odel
Maximal height: 3000 mm, depending of fluid specific weight
Mounting: Loose flange ND 65, in PPH or PVC
For dru s
Maximal height: 1000 mm, depending of fluid specific weight
Mounting: Thread 2” G, PVC or PPH
Metric buttress thread, PVC or PPH (other on request)
Autres manuels Bamo Instrument de mesure
Bamo
Bamo MAXIMAT LW CN-SDR Manuel utilisateur
Bamo
Bamo MW-10 Manuel utilisateur
Bamo
Bamo BAMOPHAR 759 Manuel utilisateur
Bamo
Bamo BAMOPHAR 107 Manuel utilisateur
Bamo
Bamo TURBISENS Manuel utilisateur
Bamo
Bamo DF 1000 A Manuel utilisateur
Bamo
Bamo IER Turbicube 20 Manuel utilisateur
Bamo
Bamo 9336 Manuel utilisateur
Bamo
Bamo MAGTOP 300 Manuel utilisateur
Bamo
Bamo Pooltest 3 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur