Baby Style TS2 Manuel utilisateur

IMPORTANT –KEEP FOR FUTURE REFERENCE

Please read these instructions carefully before using your new

Travel System / Pushchair. Keep this manual in a safe place for

future reference.

Instruction manual

Important Safety Information ……………………………………… 4

Primary features …………………………………………………….... 5

Opening the pushchair ……………………………………………… 5

Folding the pushchair …………………………………………….…. 5/6

Operating the swivel wheels ……………………………………….. 6

Fitting/Removing the bumper bar ………………………...………. 6

Adjusting the seat backrest …………………………………………6

Adjusting the leg rest …………………………………………………6

Using the brake ……………………………………………………….. 7

Using the safety harness ……………………………………………. 7

Fitting/Removing the hood ………………………………..………... 7

Fitting the apron ………………………………………………………. 7

Fitting the car seat ……………………………………………………. 8

Removing the car seat ……………………………………………….. 8

Adjusting the suspension …………………………………………… 8

Fitting the newborn liner ………………………………………..…… 8/9

Removing the newborn liner ……………………………………….. 9

Fitting the rain cover ……………………………………………….… 9

Removing the shopping basket ……………………………………. 10

Care and maintenance ……………………………………………….. 10

Warranty ………………………………………………………………...11

CONTENTS

1. WARNING: A child’s safety is your responsibility

2. WARNING: Children should never be left unattended in this vehicle.

3. It is important that any person intending to use this vehicle fully understands the

instructions.

4. WARNING: Children should be harnessed in this vehicle at all times. Use the

five point harness that is provided or one that complies with BS 6684, make sure

the harness is securely fastened to the “D-rings” situated on the integral harness

either side of the seat. Adjust the harness to its correct position with the use of

the adjustable straps.

5. WARNING: Children should always be kept clear of moving parts while making

adjustments to the vehicle.

6. Never overload the vehicle; the weight limit for the shopping basket is 2 kg,

always place articles in the centre of the tray provided. Any load attached to the

handle will adversely affect the stability of the vehicle.

7. WARNING: Incorrect assembly, folding or use of this vehicle may cause damage

and affect the safety of the vehicle.

8. It may be unsafe to use accessories (e.g. child seats, bag hooks rain covers etc.)

other than those approved by the manufacturer.

9. WARNING: Never leave the vehicle without first engaging the parking

device. Avoid uphill or downhill parking.

10. Avoid using the vehicle on steps, stairs or escalators as it may be dangerous to

your child/children.

11. Check on a regular basis to make sure that all essential components & locking

devices are functioning correctly.

12. When the pram body is used, the depth from the top of the mattress to the top of

the side of the body (or at any position within 300mm of the harness attachment

points), should not be reduced to less than 140mm when the mattress is in

position. Any mattress purchased should conform to BS1877: part 10.

13. Do not use replacement parts other than those supplied by the manufacturer or

distributor.

14. Never use this vehicle as a permanent bed for your child / children.

WARNING: A CHILDS SAFETY IS YOUR RESPONSIBILITY.

Children should be harnessed in at all times and should never be left unattended. The child

should be clear of moving parts while making adjustments. This vehicle requires regular

maintenance by the user. Overloading, incorrect folding and the use of non-approved accessories

may damage or break this vehicle. Read the manufacturer’s instructions.

IMPORTANT SAFETY INFORMATION

OPENING THE PUSHCHAIR

Remove any packing and place out of the reach of children. Pull up

on both finger catches found just below the handle grips and lift the

pushchair, the frame will start to open. Push down gently with your

foot on the round plastic component in the middle of the A frame until

fully open. Finally press down the front of the seat to ensure the locks

at the ends of the front legs have engaged. Make sure that they have

locked into position before continuing.

FOLDING THE PUSHCHAIR

To fold the pushchair, ensure the backrest is in its most upright

position, the hood is fully folded back and the leg rest is in its lowest

position. Pull up (and hold) on the two finger catches located below

the handle…

PRIMARY FEATURES

grips and push down tilting the pushchair backwards. Now that the

chassis has started to fold pull up on the closing handle found at the

back of the pushchair. Lay the pushchair on the on the floor to ensure

that it is fully locked into position. Double check that it is locked

before transporting. If the chassis is not locked apply a little

downward pressure to the armrests until it locks fully.

OPERATING THE SWIVEL FRONT WHEELS

The front wheels can be used in swivel wheel or fixed wheel mode.

The operating lever is situated between the two wheels of each front

wheel unit. To switch between swivel or fixed wheel mode; push the

lever down for swivel wheel mode, pull the lever up for fixed wheel

mode.

FITTING/REMOVING THE BUMPER BAR

To fit the bumper bar; push in the two plastic discs (located on top of

and below the joint at the end of the armrest) and slide the bumper

bar on. To remove the bumper bar, push in the two plastic discs and

slide the bumper bar off.

ADJUSTING THE SEAT BACKREST

The backrest can be adjusted to four different positions. To lower the

backrest, squeeze together the two levers at rear of the seat backrest

and recline the seat back. Release the levers to lock in the required

position. To raise the seat backrest push the centre of the back of the

seat up and forwards until the seat reaches the desired position. It

will lock into place automatically.

To adjust the seat backrest to one of its four positions; pull up the

adjustment handle in the centre of the back of the seat backrest until

the seat backrest moves freely. Reposition the seat backrest to one

of the desired four positions and release the adjustment handle.

TIP: If the seat backrest appears to rest at an angle, reposition the

seat recline so that it is supported equally on both sides of the seat in

a level position.

ADJUSTING THE LEG REST

The leg rest can be adjusted for comfort. To lower or raise the leg

rest, pull with your fingers the catches found on either side of the leg

rest and rotate the leg rest into the preferred position. Release the

catches to lock the leg rest on that position.

USING THE BRAKE

To engage the brake: Press down on the brake lever (located

between each set of rear wheels) with your foot. Check that the brake

is fully engaged on both sets of wheels. If the brake does not engage

fully when applied move the pushchair forwards or backwards slightly

and re apply the brake so that it is fully engaged. To release the

brake, with your foot lift up the brake lever until the wheels move

freely.

NEVER LEAVE THE PUSHCHAIR WITHOUT FIRST ENGAGING

THE BRAKE. CHECK THE BRAKE IS FULLY ENGAGED BEFORE

LEAVING THE PUSHCHAIR

USING THE SAFETY HARNESS

Always apply the parking brake before placing your child in the

vehicle. The safety harness has two shoulder straps, a waist belt and

a crotch strap. Place the two shoulder straps over the child’s

shoulders and the waist belt around the child’s waist, the crotch strap

should be placed between the child’s legs, the waist belt & shoulder

straps should be clipped into the buckle at the end of the crotch strap.

The harness can be adjusted to suit your child by sliding the adjusters

along the shoulder straps and waist belt. To release the safety

harness, push the buttons on the centre buckle. D-rings for attaching

a separate harness conforming to BS 6684 can be found attached to

the integral harness at the base of the waist straps. ALWAYS USE

THE CROTCH STRAP IN COMBINATION WITH THE WAIST BELT.

ALWAYS USE THE SAFETY HARNESS.

FITTING/REMOVING THE HOOD

Clip the hood into position on both sides, the hood clips attach to the

corresponding part near the back of the armrest on the pushchair seat

unit.

FITTING THE APRON (Pushchair)

Fit the apron by attaching the press-studs on the top of the apron to

the corresponding press-studs on the inside of the hood. Use the

elasticated bottom part of the apron to cover the foot rest. The apron

can be fitted either over or under the bumper bar if the bumper bar is

fitted.

FITTING THE CAR SEAT

Fold the pushchair hood backwards to the open position. Recline the

pushchair seat to the fully reclined position.

Release the fabric that covers the arm rests left and right (attached by

press-studs) and fold the arm rest fabric into the seat base. Unfold

the car seat adaptors by rotating them into the upright position,

ensuring they are fully open. Gently lower the car seat over the

adaptors and push on to the adaptors, the adaptors will click into the

locked position when correctly fitted. Check the car seat is securely

fitted by carefully lifting the car seat away from the pushchair. Raise

the pushchair seat back until it locks in position against the car seat.

REMOVING THE CAR SEAT

To remove the car seat from the pushchair; holding the car seat

handle in the upright position in one hand release the two buttons in

the adaptors (left and right) by pushing in. Slowly lift the car seat away

from the pushchair. Fold the adaptors down and replace the armrest

covers by attaching the press-studs.

ADJUSTING THE SUSPENSION

To adjust the rear wheel suspension, rotate the knob clockwise to the

desired setting. Repeat for both sides. The suspension has two

settings, soft and firm.

NEWBORN LINER

The liner has been designed for use with the Babystyle TS2 pushchair

and should not be used with any other product. The liner creates a

lie-flat environment for your child from birth up to a maximum of 9kg

THE MAXIMUM WEIGHT OF THE CHILD IN THE NEWBORN

LINER SHOULD NOT EXCEED 9kg

FITTING THE NEWBORN LINER

Open the pushchair and remove the hood.

Recline the seat backrest to the fully reclined position.

Release the press-studs on the fabric armrests and fold the fabric

onto the pushchair seat, the fabric of the arm rests will overlap each

other on the seat base.

Unfasten the press-stud on the crotch strap and remove from the

bumper bar, refasten the press-stud and lay the crotch strap on top of

the arm rest fabrics on the seat base.

Lift up the leg rest up so that it touches the bumper bar.

Place the liner in the seat unit and fasten the press-studs on the

outside of the liner to the corresponding press-studs on the arm rests.

Fasten the Velcro on the underside of the leg rest with the

corresponding Velcro in the end of the liner.

Fasten the press-studs to the outside wings of the seat back rest (one

left one right) with the corresponding press-studs on the liner.

Fasten the Velcro strips on the base of the liner to the Velcro strips on

the top of the back of the reclined seat backrest.

Thread the D-rings (found on the waist belt of the pushchair harness)

through the openings in the base of the liner.

The D-rings are anchorage points for an independent harness.

WARNING Use a harness as soon as your child can sit unaided.

Place the mattress in the liner with the thickest part at the end nearest

the bumper bar.

Fit the hood so that the fabric at the back of the hood covers the

raised leg rest.

Click the plastic fittings on the hood onto the corresponding fittings on

the pushchair. You will have to rotate the plastic fittings on the hood

to position the hood correctly.

Fit the apron by attaching the press-studs on the front flap of the

apron to the press-studs on the inside of the hood.

Place the top of the apron over the top of the liner and attach the

fastening at the end of the apron to the matching fastening at the foot

end of the liner.

REMOVING THE LINER

To remove the liner, release the press-studs and Velcro fasteners and

lift the liner from the pushchair.

FITTING THE RAIN COVER

The rain cover can be used with the stroller in all combinations.

Drape the rain cover over the stroller seal the fastenings.

REMOVING THE SHOPPING BASKET

To remove the shopping basket: Unhook the loops at the front of the

basket and release the press-studs at the back of the basket.

CARE AND MAINTENANCE

Regularly check screws, rivets, bolts & fastenings to ensure they are

locked tight and secure. Replace any parts in an inferior condition.

Should you intend to use the pushchair during the winter, by the sea

or off-road; it is important to clean thoroughly & dry the vehicle after

use. Salt from the ocean or from roads will corrode metal parts if not

removed after use.

Check on a regular basis that all chassis locking devices are

working correctly.

If any part of the pushchair is damaged contact your local Babystyle

retailer immediately without using the pushchair.

Do not expose your pushchair to excessive sunlight for extensive

periods of time.

Take care not to tear the fabrics while transporting the pushchair.

Petroleum jelly is suitable to use as a lubricant for moving parts.

Ensure that zips are either fully open or fully closed or they may be

damaged.

Always use the rain cover in inclement weather.

Do not place items on the hood/canopy, it may damage the vehicle

and/or render it unsafe.

Rubber tyres can leave marks on some surfaces. The tyres can

react with some surfaces (vinyl floor coverings, carpets etc.) and

cause stains. Always stand the stroller on a protective surface

indoors.

Routinely clean the metal parts with a damp cloth & then dry

immediately.

Fabrics should be cleaned using lukewarm water and a mild

washing detergent. Do not wash in the washing machine.

Table des matières

Autres manuels Baby Style Poussette

Baby Style

Baby Style OYSTER Manuel utilisateur

Baby Style

Baby Style LUX SBD Manuel utilisateur

Baby Style

Baby Style Prestige Manuel utilisateur

Baby Style

Baby Style OYSTER Manuel utilisateur

Baby Style

Baby Style OYSTER MAX OM2 Manuel utilisateur

Baby Style

Baby Style OYSTER Manuel utilisateur

Baby Style

Baby Style Oyster Atom Manuel utilisateur

Baby Style

Baby Style OYSTER 2 OY2 Manuel utilisateur

Baby Style

Baby Style Lux 3 in 1 Manuel utilisateur

Baby Style

Baby Style Oyster twin lite Manuel utilisateur

Baby Style

Baby Style Hybrid 2 Manuel utilisateur

Baby Style

Baby Style hyBrid swivel S Manuel utilisateur

Baby Style

Baby Style light'nmove Manuel utilisateur

Baby Style

Baby Style OYSTER Manuel utilisateur

Baby Style

Baby Style Oyster Zero Manuel utilisateur

Baby Style

Baby Style EGG Manuel utilisateur

Baby Style

Baby Style Qyster 3 Manuel utilisateur

Baby Style

Baby Style OYSTER Manuel utilisateur

Baby Style

Baby Style Oyster2 Manuel utilisateur

Baby Style

Baby Style hyBrid ezyfold S116 Manuel utilisateur

Baby Style

Baby Style Oyster lite 2 Oyster Air S673 Manuel utilisateur

Manuels Poussette populaires d'autres marques

Hauck

Hauck Priya Trioset Manuel utilisateur

CHILDHOME

CHILDHOME CWQDN Manuel utilisateur

Dreamer Design

Dreamer Design Rebound GST Manuel utilisateur

Britax

Britax STEELCRAFT AGILE Manuel utilisateur

Graco

Graco 7427 Manuel utilisateur

Comfort

Comfort COMPASS Manuel utilisateur

OBaby

OBaby Aura Manuel utilisateur

Tutek

Tutek Tirso Manuel utilisateur

Babify

Babify Dual Plus Manuel utilisateur

Graco

Graco Stroller Manuel utilisateur

Special Tomato

Special Tomato Jogger Manuel utilisateur

Chicco

Chicco CORTINA TOGETHER TWO-PASSENGER STROLLER Manuel utilisateur

Otto Bock

Otto Bock Kimba neo Manuel utilisateur

Milly Mally

Milly Mally ROYAL Guide de démarrage rapide

Hauck

Hauck DUETT 3 PRAM Manuel utilisateur

BOB

BOB DUALLIE Manuel utilisateur

Nuna

Nuna Pepp Manuel utilisateur

Britax

Britax B2 Manuel utilisateur