Baby Lock Model BLCS Manuel utilisateur

SERVICE MANUAL

MODEL BLCS

Vol 3.1

From

Serial Numbers

For U.S.A. For Canada For Europe,

Australia,NZ

100061100390 100383

1.Construction of Covers

10.1

4.6

2.0

Distance of chain looper tip from

center of chain looper shaft

Distance of lower looper tip from

center of lower looper shaft

Distance of upper looper tip

from right side of overlock

right needle(O2)

Distance of lower looper tip

from right side of overlock

right needle(O2)

Distance of chain looper tip

from right side of chain

right needle(C3)

55.4

72.8

4.9 8.6

Height of

feed dog

Height of

presser foot

Height of overlock

right needle(O2)

Adjusting gauge

For BLE8

2. Adjustment of Needle,Chain lopper & Presser foot

Height of presser foot

4.8 +0.1

R72.4

0.1

Height of needle Chain looper adjustment

1.8 0

+0.1

ELx705CF 90/14 ELx705CF 90/14

ELx705CF 90/14

C3 Needle

Needle plate

12.5+0.05

C3 Needle

2.3+0.2

Chain

Needle

Chain

Needle

Needle guard adjustment

0.2-0.3

FRONT

SIDE

FRONT

SIDE

0-0.02

Chain needle

front needle

guard

Back

needle guard

C3Needle

Chain needle

& Chain looper

0-0.1

3. Height of feed dog

CORRECT HEIGHT – When feed dogs are top position, make sure the clearance

of 0.9mm between presser foot and needle plate.

4. Tension release & Dropped feed dog adjustment

4-1.Tension release

a) In case you replace face cover, make sure the tension release lever

catches the Tension release pin correctly (fig.A)

b) Double check disks are open perfectly when presser bar lifter is lifted.

4-2. Dropped feed dog adjustment

Make sure feed dog height is correct,before you adjust following items.

a) Loosen adjusting screw (B).

b) Lift the presser bar lifter and make sure feed dog is dropped position.

c) Rotate machine pully, Make sure Feed dog crutch arm (E) swings up and

down.

d) Tighten the screw (B) until Feed dog crutch arm does not swing.

e) Drop the presser bar lifter, make sure dropped feed dog mechanism does

work correctly when presser bar lifter is lift position.

0.9 +0.1

3.Height of feed dog

4.Tension release & Dropped feed dog adjustment

5. Checking threading steel pipe joint

a) Set the machine for looper threading.

b) Move the lock button release lever slightly to the right.

c) Check the connecting point whether the looper threading pipe joint and threading

steel pipe is fitted each other properly.

6. Checking pump

6-1 Checking deflate from pump

Holding the pump tube 6, push down the pump lever 15 and check if air is deflated

from pump or not.

6-2 Replacement of Piston Cap

a) Bring the pump lever to the lowest position and fix it with Scotch tape or something like that.

b) Remove bace plate.

c) Remove piston driving arm fixing screw 11 (SM3005IK).

d) Remove piston driving arm from piston driving shaft.

(It will be easy to remove the arm from the shaft, if you push the shaft to the rightward direction.)

e) Remove piston assembly from cylinder

(It will be easy to remove piston assenbly from cylinder, when the needle is in the lowest position.)

f) Replace piston cap.

g) Greace piston cap a little bit.(MOLYKOTE EM-50L)

h) Return piston assembly to cylinder.

i) Fit piston driving arm to piston driving shaft properly and tighten fixing screw SM3005IK firmly.

(It will be easy to fit the armto the shaft, if you push the shaft to the leftward direction.)

j) Check and confirm whether the pump works properly or not.

k) fix bace plate.

Threading steel

pipe

Proper position Unproper position

Joint

5.Checking thread

steel pipe joint

6.Checking pump

8. Trouble Shooting

7. Adjustment of thread take-up

7-1 NEEDLE THREADS ARE UN BALANCED ;

* Is the BLCS threaded correctly? See Instruction Book P.14,15.

* Are the threads snapped in the head guide? See Instruction Book P.15.

* Are the threads recommended high quality? See Instruction Book P.7.

7-2 LOOPER THREADS ARE UNBALANC ED ;

* Is the BLCS threaded correctly? See Instruction Book P.14,15.

* Are the threads snapped in the head guide? See Instruction Book P.15.

* Are the threads recommended high quality? See Instruction Book P.7.

7-3 THREAD BREAKS ;

* Is the BLCS threaded correctly? See Instruction Book P.14,15.

* Are the threads snapped in the head guide? See Instruction Book P.15.

* Are the threads recommended high quality? See Instruction Book P.7.

7-4 JET AIR THREADER DOES NOT WORK

*Is air deflated from pump? See P.13.

*Are pipes connected properly? See P.13.

*Are there any lints or thread in pipes?

BLCS3

Correct Position

(Thread take-up is

lowest position.)

CORRECT POSITION: When thread take-up is lowest position, thread take-up and

thread guide are same position. See illustration below.

a). Rotate the machine pully and bring thread take-up at the lowest position.

b). Loosen thread take-up height position adjusting screws.

c). Adjust the thread take-up to correct position. See illustration below.

d). Tighten the fixing screws.

Thread take-up

height position

adjusting screws

Autres manuels pour Model BLCS

Table des matières

Autres manuels Baby Lock Machine à coudre

Baby Lock

Baby Lock A-LINES Sofia BL137A Manuel technique

Baby Lock

Baby Lock Capella Manuel technique

Baby Lock

Baby Lock Pearl BLQF Manuel utilisateur

Baby Lock

Baby Lock A_LINE Maria BL23A Instructions de montage

Baby Lock

Baby Lock Katherine BL210A Instructions de montage

Baby Lock

Baby Lock espire BLSR Manuel utilisateur

Baby Lock

Baby Lock Anna BL20A Manuel technique

Baby Lock

Baby Lock BL-6800 Manuel utilisateur

Baby Lock

Baby Lock BLDY Manuel utilisateur

Baby Lock

Baby Lock Ellisimo BLSO Manuel utilisateur

Baby Lock

Baby Lock Triumph BLETS8 Manuel technique

Baby Lock

Baby Lock Quilter's Choice Professional BLQP Manuel technique

Baby Lock

Baby Lock PRO BL8800 Manuel utilisateur

Baby Lock

Baby Lock BLSOG Manuel utilisateur

Baby Lock

Baby Lock esante BLN Manuel utilisateur

Baby Lock

Baby Lock Destiny BLDY Manuel technique

Baby Lock

Baby Lock Ellisimo GOLD BLSOG Manuel utilisateur

Baby Lock

Baby Lock Crescendo BLCR Manuel technique

Baby Lock

Baby Lock Quest BLQ2 Manuel utilisateur

Baby Lock

Baby Lock esante BLN Manuel utilisateur

Baby Lock

Baby Lock PRESTO Manuel technique

Baby Lock

Baby Lock Jewel BL J18 Manuel technique

Baby Lock

Baby Lock Celebrate BLS1 Manuel technique

Baby Lock

Baby Lock A-LINE Lauren BL450A Manuel technique

Manuels Machine à coudre populaires d'autres marques

Riccar

Riccar RL634DE Manuel utilisateur

Singer

Singer 2517 Manuel utilisateur

Pfaff

Pfaff 3307-1 SERIES Manuel utilisateur

Janome

Janome Quilt Maker Pro 18 VERSA Manuel utilisateur

Siruba

Siruba C007JP Manuel utilisateur

Husqvarna Viking

Husqvarna Viking Designer SE Manuel utilisateur

Singer

Singer 148-5 Manuel utilisateur

IKEA

IKEA SY Manuel utilisateur

Pfaff

Pfaff 571 Manuel utilisateur

Singer

Singer 15-91 Manuel utilisateur

Brother

Brother BB370 Manuel utilisateur

Pegasus

Pegasus WT100 Series Manuel utilisateur

Reliable

Reliable 7100DB Manuel utilisateur

Pfaff

Pfaff 937 Manuel utilisateur

Singer

Singer 6038 Manuel utilisateur

Singer

Singer 413K Manuel utilisateur

Pfaff

Pfaff 1471 E1 Manuel utilisateur

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuel utilisateur