B-52 MP 5712B Manuel utilisateur

MOBILE ENTERTAINMENT SYSTEM

INSTRUCTIONS MANUAL

MP 5712B

CAR CD/ MP3 PLAYER / RECEIVER

USB /SD /MMC /SLOT/ BLUETOOTH

www.b52audio.com

INSTRUCTIONS MANUAL 02 - 20

MANUAL DE INSTRUCCIONES 21 - 40

MANUAL DE INSTRUÇÕES 41 - 61

ENGLISH

MUTE

LOUD

MP 5712B

Installation

Additional information

General operations

Radio operations

CD/SD/MMC/USB Operations

MP3 WMA overview

Remote control layout

Specification

Before playing discs

Trouble shooting

Bluetooth

INDEX

PRECAUTIONS

Choose the moun ting location where the unit will not interfere with the normal driving function

of the driver.

Bef ore final ly installing the unit, connect the wiring tempor arily and make sure it is all

connected up properly and the unit and the system work properly.

Use only the parts included with the unit to ensure proper installation. The use of unauthorized

parts can cause mal functions.

Con sult with your nearest dealer if installation requires the drilling of holes or other

modifications of the vehicle.

Install the unit where it does not get in the driver’s way and cannot injure the passenger if there

is a sudden stop. Like an emergency stop.

If installation angle exceeds 30 from horizontal, the unit might not give its optimum

performance.

Avoid installing the unit where it would be subject to high temperature, suchas from direct

sunlight, or from hot air, form the heater, or where it would be subject to dust, dirt or excessive

vibration. Do not expose this equipment to rain or moisture.

DIN FRON T-MOU NT (Method A)

Installing the unit

1. Dashboard

2. Holder

After inserting the holder into

the dashboard, select the

appropriate tab according to

the thickness of the dashboard

material and bend them

inwards to secure the holder in

(Fig. 1) place.

3. Screw

INSTALLATION

(Fig. 1)

1. Dashboard

2. Nut (5mm)

3. Spring Washer

4. Screw (5 x 25mm)

5. Screw

6. Strap

Be sure to use the strap to

secure the back of the unit in

place. The strap can be bent by

hand to the desired angle.

7. Plain Washer

INPUT THE SD CARD

The SD oblique angle keeps

rightward exposure, put into

the SD slot and press it again

to eject.

1. Frame

2. Insert fingers into the groove in the front

of frame and pul l out to remove the frame.

(When reatt achi ng the frame, point the

side with a Groove dow nwards and attach

it. )

3. Lever

Insert the levers supp lied with the

unit into the grooves at both sides of

the unit and shown in figure until they click.

Pulling the levers makes posible to remove

the unit from the dashboard.

DIN REAR-MOUNT (Method B)

Installation using the screw holes on

the sides of the unit.

INSTALLATION

(Fig.2)

(Fig.3)

Removing

the

uni t

ADDITIONAL INFORMATION

SPEAKER CONNECTION

HOW TO INSTALL AND REMOVE THE FRONT PANEL

INSTALLING THE FRONT PANEL

To install the front panel, insert the panel into the housing and make sure the panel is properly

installed, otherwise, abnormalities occurs on the display or some keys will not function properly

GENERAL OPERATIONS

FRONT PANEL LAYOUT

1. POWER BUTTON

2. RELEASE BUTTON

3. VOLUME/ SEL BUTTON

4. MUTE BOTTON

5. MODE SWITCH

6. DISPLAY BUTTON

7. LCD DISPLAY

8. FLASHING LED

9. RESET BUTTON

10. BAND SWITCH

11. TUNE SEEK Y TRACK FORWARD BUTTON

12.TUNE SEEK Y TRACK REVERSE BUTTON

13. AUTOMATICALLY MEMORY STORING

14. PLAY/PAUSE Y PRESET BUTTON 1

15. INTRO Y PRESET BUTTON 2

16. REPEAT Y PRESET BUTTON 3

17. RANDOM Y PRESET BUTTON 4

18. PRESET BUTTON 5

19. PRESET BUTTON 6

20. ST/MO BUTTON

21. LOC/DX BUTTON

22. LOUDNESS BUTTON

23. EJECT KNOB

24. CD SLOT

25. REMOTE CONTROL SENSOR

26. USB CONNECTER

27. SD/MMC SLOT

28. AUX IN JACK

29. SCN BUTTON

MUTE

LOUD

MP 5712B

POWER ON/OFF

Press any button to turn the unit on. Press and hold POWER button to turn off the unit.

Note: After the unit is off, the volume level and radio current settings will be memorized, and

when you turn the unit on it will resume the stored status, which you set.

FRONT PANEL RELEASE

Press REL button (2) to detach the removable front panel

SOUND ADJUSTMENT

Turn on (3) can adjust the desired volume quality.

A).Press SEL button (3)will change in the following order.

Option:

VOLUME CONTROL /SELECT

Rotating this knob, you can adjust VOL/BASS/TREB/BAL/FAD . To select the functions, press the

VOL knob shortly until the desired functions are shown on the display.

Increase or decrease the volume by turn the VOL knob right or left. These buttons can be used

to adjust the BASS, TREBLE, BALANCE and FADER.

BASS

Press VOL/ SEL button(3) one time. Adjust bass level by using VOL/ SEL(3)Knob.

TREBLE

Press VOL/ SEL button(3) two times. Adjust treble level by using VOL/ SEL(3) Knob

BALANCE

Press VOL/ SEL button(3) three times. Adjust sound balance between left and right speakers by

using VOL/ SEL(3)Knob.

FADER

Press SEL button (3) four times. Adjust sound balance between front and rear speakers by using

VOL/ SEL(3)Knob.

MUTE

Press MUTE button (4) to mute down the sound. Press it again to release this mode and recover

previous volumen level.

OTHERS ADJUSTMENT

Press VOL/SEL button (3) for several seconds, it is activated as cyclical mode of following

functions for user´s selection.

VOL BAS TRE BAL FAD

(Volume) (Bass)(Treble) (Balance) (Fader)

Press and hold this button will go to different modes:

Press and hold will go to DSP mode automatically:

By turning this function button to chose Flat, CLASSIC, Pop and Rock.

By press the function button to select your favoryte DSP mode.

When in the DSP mode, press the function button once will to ESP mode:

By turning the function button to choose 12 seconds ESP.

Vy press the function button to select your desire ESP seconds.

When in the DSP mode, press the function button twice will go to BEEP mode

(the key pad tone) by turning the function button to choose on or off by press

The function button to selecto n or off.

VOL LAST/ADJUST

This function allows to set the volumen level of the unit after it was turned off and the turne don

again. Choose VOL LAST if you want the volumen level to be the same as it was before turning off.

VOL ADJUST allows to choose volumen level.

SEEK MODE

SEEK 1: When SEEK 1 mode is activated, AUTO SEEK SCAN is stopped when station is detected

even user still push SEEK button.

SEEK 2: Auto SEEK SCAN is not stopped even if station is detected if user pushes SEEK button.

When releases SEEK button, the stop when station is detected.

SELECT MODE

By pressing this button(5) to go to different function mode:

- Tuner (radio)

- CD (MP3 CD) to go to this mode must be have a CD in.

- Memory Card to go to this mode must be have a Memory Card in.

- USB to go to this mode USB device must be connected.

- AUX in put

DISPLAY

Press DISP button (6) to operate as the conversion of each display mode as follow:

- Time is displayed for 5 sec when DISP key is pressed, and it returns to its previous display

(Folder, File name...) unless DISP key is pressed again.

3) From the clock mode, when DISP Key is pressed for longer than 1sec, clock mode switches to

clock Adjusting mode and the clock display begins flashing. At this time clock can be changed by

pressing ( + / - ) , or the ENCODER VOLUME.

LIQUID CRYSTAL DISPLAY

Exhibit current frequency and activated functions on the display (7).

FLASHING LED

If the front panel does not install in the main unit, the LED (8) will be flashing.

BAND SELECTION

At tuner mode, press BAND button (10) to select the desired band. The

reception band will change in the following order:

STATION SELECTION

Press TUNE/SEEK/TRACK FORWARD button (11) or TUNE/SEEK/TRACK REVERSE button (12)

shortly for manual tuning function.

Press for several seconds the automatic tuning mode ( SEEK

mode) is selected.

AUTOMATICALLY MEMORY STORING & PROGRAM SCANNING

- Automatically Memory Storing

Press AMS(MP3) button (13) for several seconds, the radio searches from the current frequency

and checks the signal strength until one cycle search is finished.

And then 6 strongest stations are stored into the corresponding preset number Button

- Program Scanning

Press AMS(MP3) button (13) shortly to scan preset station. When the field strength level is more

than the threshold level of stop level, the radio is holding at that preset number for several seconds

with releasing mute, then searches again.

STATION STORING

Press preset button (14~19)

1) RADIO MODE. M1 ~ M6

- PRESET MEMORY is loaded when key is pressed for less than 1 second.

- PRESET MEMORY is saved when key is pressed for longer than 1 sec.

2) CD/ MP3 / FLASH MP3 PLAY / PAUSE Press preset button (14) is activated. During a PAUSE,

DISC INDICATOR flashes.

TOP - First song will play whe n Top key is pressed for longer than 0.5sec during play.

INT

Press preset button (15): During INTRO ON, INT indicator comes on and

begins playing the first 10sec of each song, until the last song is played. It begins

playing the entire track from where INT started

MO/ST SELECTOR

Press ST (20) button to select MONO or STEREO mode.

When “ST” appears in the LCD display. During the player mode, press the button to switch left

speaker / right speaker/stereo.

RADIO OPERATIONS

LOC/DX SELECTOR

Press LOC (21) button to select strong or weak station reception. It is set to LOC mode when LOC

(21) button is first pressed. “LOC” appears and only local station is available. It is switched to DX

mode when LOC (21) button is pressed again. Both distance and local stations can be received.

LOUDNESS ON/OFF

Press LOU (22) button to increase the low frequency. This can improve the sensitivity of your

ears. And “LOUD” appears in the LCD when the loudness mode is activated.

SCAN

Press scan button (29) to search radio station.When a station signal strength

level more than the level to stop.The radio will playing the station for 5

seconds and the frequency blinking on the LCD at the same time.

Press and hold scan button (29) more than 3 seconds to select the station which

you desired.The radio will start play the station.

AREA USA/EUR SETUP

In Radio mode. Press SEL button for several seconds. LCD with show from DSP OFF/ON AREA USA/

EUR. At AREA USA/EUR. You can use VOL +/- to select the AREA frequency.

Table des matières

Langues :

Autres manuels B-52 Système stéréo de voiture

B-52

B-52 DV-8772 Manuel utilisateur

Manuels Système stéréo de voiture populaires d'autres marques

JL Audio

JL Audio Stealthbox SB-CAN-G2MVX3D/10TW3 Manuel utilisateur

Clarion

Clarion PU-9836A Manuel utilisateur

Sony

Sony MEX-BT5750U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AR0M Manuel utilisateur

Sony

Sony RM-X7BT Manuel utilisateur

Insignia

Insignia NS-HD5113 Manuel utilisateur

Clarion

Clarion BTD3341 Manuel utilisateur

USA SPECS

USA SPECS PA11-VW6 Manuel utilisateur

Sony

Sony MEX-N4380BT Manuel utilisateur

Kenwood

Kenwood KCD-BT6544U/UY Manuel utilisateur

JVC

JVC KD-DB912BT Manuel utilisateur

Philips

Philips CSQ405/98 Manuel utilisateur

Alpine

Alpine TDM-7544 Manuel utilisateur

Autotek

Autotek TransAm TA 1400 Manuel utilisateur

Clarion

Clarion PN-3124N-A Manuel utilisateur

Denso TEN

Denso TEN FT0108A Manuel utilisateur

Pyle

Pyle PLD57MU Manuel utilisateur

Harman

Harman Chrysler Radio Navigation System RB4 Manuel utilisateur