Axminster SIEG C4 Manuel utilisateur

2007

600856

SIEG C4

Bench Lathe

Axminster Reference No: C4

User Manual

WHITE

AXMINSTER

W

www.axminster.co.uk

600857 Mill Attachment for

the C4 Lathe (Optional)

Manual (See Pages 20-41)

600856 C4 Bench Lathe

Manual (See Pages 02-19)

No. 4 Spanner Set Change Wheel Gears Comprising of:

No. 1 Main Chuck Key

No. 4 External Jaws

No. 4 Internal Jaws

Set of Allen Keys

No. 1 2MT Dead Centre

No. 1 3MT Dead Centre

ACCESSORY'S

PACKING LIST

No.1 127 Teeth

No.2 100 Teeth

No.1 80 Teeth

No.1 70 Teeth

No.1 56 Teeth

No.1 55 Teeth

No.2 50 Teeth

No.1 49 Teeth

No.1 45 Teeth

No.1 40 Teeth

No.1 35 Teeth

4

5

6

2a. SCREW CUTTING

For selection of the required thread pich please refer to the chart on the gear train cover, select

the correct gears from the change wheel set and mount them in the correct sequence.

(See fig 1 & 1a)

A

B

C

D

Fig 1 Fig 1a

GEAR CHART

7

2a. SCREW CUTTING CONTINUED

PIVOTING BRACKET

CLAMPING BOLT

The "C/B" axis is adjusted via the pivoting bracket and clamp bolt as shown. (See figs 2 & 2a)

Fig 2a

Fig 2a

4. THE CARRIAGE/SADDLE

8

9

Note: The chuck guard must be in the lower position as there is a interlock switch

proventing the machine operating with the guard in the raised position.

Your C4 bench lathe is a precision tool. In order to maintain this precision and prolong its useful

life, it is advised that you follow the recommended daily and periodic maintenance tables printed

below.

Daily and Periodic Maintenance

Daily Pre-use

1. Using an oil can with a narrow nozzle, oil all the oil points on the machine, incl.

A) Saddle (4), B) tailstock (2), C) traverse slide (1), D) compound slide (2), E) leadscrew gearbox (2),

and F) leadscrew end bearing (1).

2. Move the traverse and compound slides to give access to their drive shaft threads and

lightly coat with oil, work the oil up the threads to lubricate the thread followers.

3. Spray-oil the slides and the lathe bed, exercise the saddle and the slides to spread the oil

to all surfaces, both hidden and visible.

4. Spray up under the rack cover to lubricate the rack. (G)

5. Apply oil to the change gears and their axle mountings. (H)

Daily after-use

1. Clean all swarf and chips away from the machine bed, slide surfaces, and the tool post.

2. Exercise the slides and ensure no swarf etc., is lodged in the drive shaft tunnels.

3. If you have been using ʻsudsʼ make sure the machine is throughly dried off. Clear the suds

tray of all swarf and chips, especially around the drain.

4. Check the tool, ensure it is usable the next time, if not re-sharpen or replace the tool tip.

5. Lightly oil spray all the machine beds and surfaces, and the tailstock barrel.

6. Clean and lightly oil any tools you may have been using (centres, drill chucks, spanners

chuck keys etc, and put them away.

7. Switch off the power supply. Disconnect the plug.

8. Cover the machine over with a dust cloth.

Weekly

a) Check the belt tension.

b) Check the tautness of the slides.

c) Check the level of the suds reservoir. (if you are using suds).

Accessories

May we recommend the following products for use with your C4 lathe.

Grease - Rocol Saphire 2 (Part number: 810129).

Lubricant - Rocol Slideway lubricant spray (Part Number: 810141).

Cutting Fluid - Rocol Multisol cutting fluid (Part Number: 810140).

There are numerous accessories listed for the machine listed in the Axminster catalogue

in section 1

LATHE MAINTENANCE

10

Table des matières

Autres manuels Axminster Tour

Axminster

Axminster AP508WL Manuel utilisateur

Axminster

Axminster AT1416VS Manuel utilisateur

Axminster

Axminster Professional AP310T2 Manuel utilisateur

Axminster

Axminster Engineer Series Manuel utilisateur

Axminster

Axminster AW240WL Manuel utilisateur

Axminster

Axminster Professional AP406WL Manuel utilisateur

Axminster

Axminster Workshop AW355WL Manuel utilisateur

Axminster

Axminster WL-46A Manuel utilisateur

Axminster

Axminster AWVSL900 Manuel utilisateur

Axminster

Axminster AWVSL900 Manuel utilisateur

Axminster

Axminster SIEG X1 Super Micro Mill Mk2 Manuel utilisateur

Axminster

Axminster AH-1218 Manuel utilisateur

Axminster

Axminster AW370WL Manuel utilisateur

Axminster

Axminster SIEG Model Engineer Series Manuel utilisateur

Axminster

Axminster AWVSWL1200D Manuel utilisateur

Axminster

Axminster Hobby Series Manuel utilisateur

Axminster

Axminster AW305WL Manuel utilisateur

Axminster

Axminster C0 Manuel utilisateur

Axminster

Axminster AT1628VS Manuel utilisateur

Axminster

Axminster CQ6230A-2/910 Manuel utilisateur

Axminster

Axminster AW1416VS Manuel utilisateur

Axminster

Axminster SIEG SC6 Manuel utilisateur

Axminster

Axminster WORKSHOP AW205WL Manuel utilisateur

Axminster

Axminster AWSL Manuel utilisateur

Manuels Tour populaires d'autres marques

Kval

Kval 990-H Manuel utilisateur

Holzmann

Holzmann VD 1100ECO Manuel utilisateur

Grizzly

Grizzly G0632 Guide de démarrage rapide

Grizzly

Grizzly G0462 Manuel utilisateur

Grizzly

Grizzly G0709 Manuel utilisateur

HAMAR LASER

HAMAR LASER L-700 Supplément

Promac

Promac 941VA Manuel utilisateur

Grizzly

Grizzly G0949G Manuel utilisateur

Teknatool

Teknatool Nova Mercury Manuel utilisateur

Traub

Traub TNL12.2 Manuel utilisateur

WoodFast

WoodFast M305 Manuel utilisateur

Milltronics

Milltronics ML Series Manuel

Milltronics

Milltronics SL6 Series Manuel

OmniTurn

OmniTurn GT-75 Manuel utilisateur

Jet

Jet JWL-1640EVS Manuel de service

Grizzly

Grizzly G4000 Manuel utilisateur

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN ED1000FB Manuel utilisateur

Hercus

Hercus 260 Manuel utilisateur