WoodFast M305 Manuel utilisateur
M305 Mini Lathe
Standard Stand
Extension Stand
Read the instruction manual carefully before assembling.
Keep it in order for further reference.
Specifications...............................................................................................................................................1
Unpacking and Contents..............................................................................................................................2
Assembling Base to Column........................................................................................................................3
Installing Extension Supports to Base and Column Assembly...................................................................... 3
Connecting and Adjusting the Extension Supports......................................................................................4
Adjustments.................................................................................................................................................4
Determining Proper Lathe Height.................................................................................................................4
Adjusting for Lathe Length............................................................................................................................5
Leveling the Lathe Stand..............................................................................................................................5
Installing the Optional Lathe Extension Stand..............................................................................................5
Maintenance................................................................................................................................................6
Exploded Drawing for standard stand...........................................................................................................7
Parts List for Standard Stand........................................................................................................................7
Exploded Drawing for Extension Stand........................................................................................................8
Parts List for Extension Stand......................................................................................................................8
1
Table of Contents
Specifications
152 to 195 mm
500 to 810 mm
1000 to 1619 mm
622 to 876 mm
695 to 1000 mm
616 mm
99 kgs
Width
Length
Length With Extension
Working Height
Base Length
Base Width
Weight Capacity
2
Tools Required for Assembly
Item Description
Item Description Qty
1 Base....................................................................2
2 Hex. Bolt M12x96................................................4
3 Hex Nut M12........................................................4
4 Washer 13...........................................................4
5 Washer 8.5..........................................................4
6 Foot.....................................................................4
7 Washer 8.5..........................................................4
8 Retaining Ring 8..................................................4
9 Column................................................................2
10 Hex Bolt M10x80...............................................12
11 Washer 10.5......................................................24
12 Hex Nut M10.....................................................12
13 Mounting Bracket................................................2
14 Extension Support (Outside)...............................1
15 Extension Support (Inside)..................................1
16 Hex. Bolt M10x25................................................2
17 Hex. Nut M10.......................................................2
Unpack your lathe stand from its carton and check to see that you have all of the following items. Do
not use this stand if any of these items are missing. You may cause injury to yourself or damage to your
machine.
Unpacking and Checking Contents
2 Adjustable Wrenches
Contents of Package
3
Fig.03
Fig.02
Fig.01
Assembling Base to Column
1.) Locate one Base (part #1) and one Column (part
#9).
2.) Install two bolts (part #10) and two washers (part
#11) through the Column flange and into the Base.
3.) Add two washers (part #11) and two hex nuts
(part #12) to the bolts underneath the Base. (Fig.
01)
4.) Repeat steps to complete the second Base and
Column assembly.
Installing Extension Supports to Base and
Column Assembly
1.) Make sure that feet of both base and column
assemblies are pointing outward.
2.) Assemble the Inside Extension Support bracket
(part #15) to the inside of the left Base and Column
assembly. Install two bolts (part #10) and two
washers (part #11) through the Column and into
the Inside Extension Support bracket flange. Add
two washers (part #11) and two hex nuts (part
#12) to the bolts through the flange of the Inside
Extension Support bracket. (Fig. 02)
3.) Assemble the Outside Extension Support
bracket (part #14) to the inside of the right Base
and Column assembly. Install two bolts (part #10)
and two washers (part #11) through the Column
and into the Outside Extension Support bracket
flange. Add two washers (part #11) and two hex
nuts (part #12) to the bolts through the flange of
the Outside Extension Support bracket. (Fig. 03)
Assembly
4
Fig.05
Fig.04
Fig.06
Connecting and Adjusting the Extension
Supports
1.) Slip the Inside Extension Support bracket (part
#15) into the Outside Extension Support bracket
(part #14).
2.) Add two bolts (part #16) and two hex nuts (part
#17) to the welded hex nuts located on the Outside
Extension Support bracket (part #14). (Fig. 04)
3.) Only hand-tighten at this point, secure after the
length of the mini-lathe has been determined.
Determining Proper Lathe Height
1.) Install the Mounting Brackets (part #13) to the
top of both Columns (part #9) using two bolts (part
#10) and two washers (part #11). (Fig. 05)
Add two washers (part #11) and two hex nuts (part
#12) to the bolts. Hand-tighten at this point until
proper lathe height has been determined.
2.) Next, measure the distance from the base of
the lathe to the point on the live center. (Fig. 06)
3.) Measure the distance from your elbow to the
floor.
4.) Subtract the lathe height measurement from
the elbow height measurement. This number
represents the approximate height of the lathe
stand.
Example: 1143 mm (elbow to floor) -317.5 mm (base
to live center) = 825.5 mm (stand height).
Adjustments
5
Adjusting for Lathe Length
The Woodfast Lathe Stand can be adjusted from
500 mm to 810 mm in length.
1.) Measure the length of your lathe from center of
one bolt hole to the center of the other.
2.) Loosen the two locking bolts (part #16) on the
Outside Extension Support (part# 14) and slide the
Column Supports inward or outward to the desired
length.
3.) Tighten the two locking bolts (part #16) and then
tighten the two locking nuts (part #17). (Fig. 07)
Leveling the Lathe Stand
1.) Loosen the locking nut (part # 3) on the Base
assembly.
2.) Adjust the leveling bolt (part # 2) to the desired
height.
3.) Tighten down the locking nut (part # 3) to retain
the adjustment. (Fig. 08)
Fig.07
Fig.09
Installing the Optional LatheExtension Stand
The Lathe Extension Stand is typically used to
support a lathe bed extension. However, it has
a variety of other uses such as supporting an
accessory table (not included) to hold a grinder or
sharpening system.
1.) Repeat the steps in “Assembling Base to
Column” located on page 3.
2.) Repeat the steps in “Installing Extension
Supports to Base and Column Assembly” also on
page 3.
3.) Loosen and remove the two hex nuts (part #12)
and the two washers (part #11) from the Column
Support on the right side.
4.) Install the Inside Extension Support bracket (part
#15) to the Column Support. (Fig. 09)
Fig.08
Optional Extension Stand
CAUTION! BEFORE CLEANING OR CARRYING OUT MAINTENANCE WORK, DISCONNECT THE
LATHE FROM THE POWER SOURCE (WALL SOCKET). NEVER USE WATER OR WATER BASED
PRODUCTS TO CLEAN THE LATHE STAND.
Periodically check all of the stand bolts and tighen when necessary.
Make sure that the lathe stand is level.
Remove all saw dust and chips from the lathe stand after each use.
6
Fig.10
5.) Repeat the steps in “Connecting and Adjusting
the Extension Supports” located on page 4.
6.) Repeat the steps in “Determining Proper Lathe
Height” also on page 4.
7.) Next, adjust for lathe bed distance, following
the instructions in “Adjusting for Lathe Length”
located on page 5.
8.) Mount the lathe extension to the stand by using
the hardware provided. (Fig. 10)
9.) Level the Extension Stand by following the
instructions found on page 5.
Maintenance
7
Exploded Drawing for Standard Stand
Parts List for Standard Stand
Ref No.
1
2
3
4
5
6
7
8
9
10
Description
Base
Hex. Bolt M12x96
Hex. Nut M12
Washer 13
Washer 8.5
Foot
Washer 8.5
Retaining Ring 8
Column
Hex. Bolt M10x80
Ref No.
11
12
13
14
15
16
17
18
19
20
Description
Washer 10.5
Hex. Nut
Mount bracket
Extension support (outside)
Extension support (inside)
Hex. Bolt M10x25
Hex. Nut
M8x35 Hex. Bolt
8mm Washer
M8 Hex. Nut
8
Exploded Drawing for Extension Stand
Parts List for Extension Stand
Ref No.
1
2
3
4
5
6
7
8
9
10
Description
Base
Hex. Bolt M12x96
Hex. Nut M12
Washer 13
Washer 8.5
Foot
Washer 8.5
Retaining Ring 8
Column
Hex. Bolt M10x80
Ref No.
11
12
13
14
15
16
17
18
19
20
Description
Washer 10.5
Hex. Nut M10
Mount bracket
Extension support(outside)
Extension support(inside)
Hex. Bolt M10x25
Hex.Nut M10
M8x35 Hex. Bolt
8mm Washer
M8 Hex. Nut
Table des matières
Autres manuels WoodFast Tour
