Axis FC-29W Guide de démarrage rapide

FC-29W

9”

UN-UNIVERSAL

Dome Housing

Installation Instructions

Safe Use of Equipment

WARNING

To reduce the risks of an electric shock, do not expose inside of this

unit to rain or moisture.

Installation on a rainy day may also cause fog around the capsule.

Installation

Installation shall be done by qualified installer only and should

conform to all local codes.

Ensuring strength of supporting Dome Housing Unit

The unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit. Recommend

use 3/8” stainless screws x four (4).

Prohibit changes or modifications of equipment

You are cautioned that any changes or modifications not expressly

approved in these instructions could void your authority to operate

this equipment.

Basic Operating Environment Condition

We provide warranty for the products that are installed under normal

outdoor -20°C ~ +50°C conditions. We are unable to provide warranty

for the products which are installed indoor and exposed to constant

high temperature over +50°C and over 90% humidity.

Operating temperature and humidity of camera varies from camera to

camera. You are requested to confirm to camera specification with

camera manufacturer and housing specification with us in advance.

i.e. -20°C or below, you are requested to use additional heater and

+50°C or above you are requested to use two blowers and Sunshield.

Fasten wires tightly.

Attention:

Keep wires away from the Fan / Heater, and do not disturb

Fan/Heater’s performance

Table of contents

1. AXIS 214 PTZ network camera housing installation………………………..P.4

2. AXIS 215 PTZ network camera housing installation……………………..…P.6

3. AXIS 233D PTZ network dome camera Housing installation……………...P.8

4. AXIS P55XX series PTZ network dome camera Housing installation…....P.10

5. AXIS Q6034 PTZ network dome camera Housing installation………...….P.12

6. Installation of FC-9002 Pole Mount Bracket and Dome housing………….P.14

7. Installation of FC-9005 Ceil Mount Bracket and Dome housing …..….…..P.15

8. Installation of FC-9006 Ceil Mount Bracket and Dome housing …….....…P.16

9. Installation of FC-9007 Corner Adapter with Wall Mount Bracket and Dome

housing……………………………………………………………………….….P.17

10. Installation of FC-9008 Corner Adapter with Wall Mount Bracket and Dome

housing ………………………………………………………………….………P.18

11. Installation of FC-9009N Wall Mount Bracket and Dome housing …….....P.19

12. Installation of FC-9009 Wall Mount Bracket and Dome housing……….…P.20

13.Installation of FC-9011 Ceil Mount Bracket and Dome housing……….…..P.21

14.Dimensions …………………………….………….....................……………..P.22

1AXIS 214 PTZ network camera Housing installation

WARNING The unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of unit. Recommend use

stainless screws.

Cables

L603

Power cable to PC board and external power supply

L704

Power cable to PC board and PTZ network camera

9” dome housing

DC12V Fan+Heater

L705

Network extension cable to internet

Component Parts for Assembly

Square-shaped upper board No. 2 side board Round-shaped bottom board

Screw the camera on, through hole B,

with washer in the back No. 3 Allen Key ( for cover and wall

mount bracket tighten)

3x12 Double Washer screws for

camera to Square-shaped upper

board,

Assembly Steps of the Camera and the Dome Housing

1-1-1 1-1-2 1-1-3

Fix No. 2 side board (Hole 2) to the

round-shaped bottom board (Hole 5)

with 3x8 Double Washer screws.

Use 4x8 double washer screws to

Fix Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Fix screws on back of

square-shaped upper board which

go through from back to front to fix

the camera on the square-shaped

upper board (Hole B) with 3x12

double washer screws.

Assembly Steps of the Cables

1-2-1 1-2-2 1-2-3

Use 4x8 double washer to Fix

Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Connect L603 to the PC board.

Connect L704 to the PC board. Connect L704 and L705 to the

camera. Cables used for camera.

1. DC 12V FAN

2. DC 12V HEATER

3. H/SENSER

4. DC 12V OUT

5. DC 12V IN

L705 L704

L704 L603

2AXIS 215 PTZ network camera Housing installation

WARNING The unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of unit. Recommend use

stainless screws.

Cables

L603

Power cable to PC board and external power supply

L704

Power cable to PC board and PTZ network camera

9” dome housing

DC12V Fan+Heater

L705

Network extension cable to internet

Component Parts for Assembly

Square-shaped upper board No. 3 side board Round-shaped bottom board

Screw the camera on, through hole G,

with washer in the back No. 3 Allen Key ( for cover and wall

mount bracket tighten)

4x10 Double Washer screws for

camera to Square-shaped upper

board,

Assembly Steps of the Camera and the Dome Housing

2-1-1 2-1-2 2-1-3

Fix No. 3 side board (Hole 1) to the

round-shaped bottom board (Hole 6)

with 3x8 Double Washer screws.

Use 4x8 double washer screws to

Fix Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Fix screws on front of square-shaped

upper board to fix the camera on

square-shaped upper board (Hole G)

with 4x10 double washer screws.

Assembly Steps of the Cables

2-2-1 2-2-2 2-2-3

Use 4x8 double washer to Fix

Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Connect L603 to the PC board.

Connect L704 to the PC board. Connect L704 and L705 to the

camera. Cables used for camera.

1. DC 12V FAN

2. DC 12V HEATER

3. H/SENSER

4. DC 12V OUT

5. DC 12V IN

L704 L705

L704 L603

3AXIS 233D PTZ network dome camera Housing installation

WARNING The unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of unit. Recommend use

stainless screws.

Cables

L605P-2

Power cable to PC board and external power supply

L704P-2.0

Power cable to PC board and camera

9” dome housing

AC24V Fan+Heater

L705

Network extension cable to internet

Component Parts for Assembly

Square-shaped upper board No. 1 side board ＆L board Round-shaped bottom board

Screw the camera on, through hole E,

with washer in the back No. 3 Allen Key ( for cover and wall

mount bracket tighten)

4x10 Double Washer screws for camera

to Square-shaped upper board,

Assembly Steps of the Camera and the Dome Housing

3-1-1 3-1-2 3-1-3

Fix No. 1 side board (Hole 1) to the

round-shaped bottom board (Hole 5)

with 3x8 Double Washer screws.

Fix screws on front of square-shaped

upper board to fix the L board on

square-shaped upper board (Hole E)

with 4x10 double washer screws.

Fix the camera to the L board with

4x10 double washer screws.

Assembly Steps of the Cables

3-2-1 3-2-2 3-2-3

Use 4x8 double washer to Fix

Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Connect L605P-2 to the PC board.

Connect L704P-2.0 to the PC board. Connect L704P-2.0 and L705 to the

camera. Cables used for camera.

1. DC 12V FAN

2. AC 24V HEATER

3. H/SENSER

4. DC 12V OUT

5. AC 24V OUT

6. AC 24V IN

L705 L704P-2.0

L704P-2.0 L605P-2

Table des matières

Autres manuels Axis Accessoires pour appareils photo

Axis

Axis T96B05 Manuel utilisateur

Axis

Axis PT IR Illuminator Kit A Manuel utilisateur

Axis

Axis T8705 Manuel utilisateur

Axis

Axis AXIS 206 Manuel utilisateur

Axis

Axis Q1656-BE Manuel utilisateur

Axis

Axis T92E series Manuel utilisateur

Axis

Axis F9114-B Manuel utilisateur

Axis

Axis 01807-001 Manuel utilisateur

Axis

Axis Q86 Front Kit A Manuel utilisateur

Axis

Axis T91A52 Manuel utilisateur

Axis

Axis F8205 Manuel utilisateur

Axis

Axis 01445-001 Manuel utilisateur

Axis

Axis 25254 Manuel utilisateur

Axis

Axis AVTPSC Manuel utilisateur

Axis

Axis Geocalla G3-3D Manuel utilisateur

Axis

Axis T96A05-V Manuel utilisateur

Axis

Axis T93F20 Manuel utilisateur

Axis

Axis TQ1602-E Manuel utilisateur

Axis

Axis T93C10 Manuel utilisateur

Axis

Axis VT Verso HPV42K1A000 Manuel utilisateur

Axis

Axis T94B01D Manuel utilisateur

Axis

Axis T94N01G Manuel utilisateur

Axis

Axis T92A00 Manuel utilisateur

Axis

Axis VT Verso Manuel utilisateur

Manuels Accessoires pour appareils photo populaires d'autres marques

Viltrox

Viltrox EF-NEX Instructions d'installation

Calumet

Calumet 7100 Series CK7114 Manuel utilisateur

Ropox

Ropox 4Single Series Manuel utilisateur

Cambo

Cambo Wide DS Digital Series Mode d'emploi

Samsung

Samsung SHG-120 Manuel utilisateur

Ryobi

Ryobi BPL-1820 Manuel d'utilisation

Aegis

Aegis ABL-36020P Manuel utilisateur

Pentax

Pentax Data Back Fc Manuel utilisateur

Fantasea

Fantasea EyeGrabber F Series Manuel utilisateur

Honeywell

Honeywell HDZ20HD Manuel utilisateur

EGO

EGO BA1400T Manuel utilisateur

Sima

Sima SRW-62 Manuel utilisateur

Shape

Shape A7SSMKIT Manuel utilisateur

Slide Kamera

Slide Kamera HST-2 Manuel utilisateur

Power works

Power works 2902613 Manuel utilisateur

SES

SES SE-2047-2 Manuel utilisateur

Olympus

Olympus PT-EP05L Manuel utilisateur

Starlite

Starlite OctoDome nxt Manuel utilisateur