AXIOMTEK MPC240 Manuel utilisateur

MPC240

24”FHD Medical Grade Panel

Computer with Intel®CoreTM i7/i5

Processors

User’s Manual

Disclaimers

This manual has been carefully checked and believed to contain accurate information.

Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third

party’s rights, and any liability arising from such use.

Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,

completeness or usefulness of any information in this document. Axiomtek does not make any

commitment to update the information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any time

without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted, in

any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written permission of Axiomtek Co., Ltd.

CAUTION

If you replace wrong batteries, it causes the danger of explosion. It is recommended by the

manufacturer that you follow the manufacturer’s instructions to only replace the same or

equivalent type of battery, and dispose of used ones.

OCT 2015, Version A1

Printed in Taiwan

iii

Symbol Index

No.

Description

Symbol

CE Marking

Manufactured by：address of the MFG

EC REP address

Refer to instruction 4 manual / booklet

Serial Number

Direct current

Alternating current

AXIOMTEK Co., Ltd.

8F., No.4, Lane 235, Baoqiao Road, Xindian District,

New Taipei City 231, Taiwan (R.O.C.)

http://www.axiomtek.com.tw

Made in Taiwan

MEDNET GmbH, Borkstrasse 10, 48163 Muenster, Germany

Safety Precautions

Before getting started, please read the following important safety precautions.

1. The MPC240 Series does not come equipped with an operating system. An operating

system must be loaded first before installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when installing the internal

components. Use a grounding wrist strap and place all electronic components in any

static-shielded devices. Most electronic components are sensitive to static electrical

charge.

3. Disconnect the power cord from the MPC240 Series before making any installation. Be

sure both the system and external devices are turned OFF. A sudden surge of power

could ruin sensitive components. Make sure the MPC240 Series is properly grounded.

4. Make sure the voltage of the power source is correct before connecting the equipment to

the power outlet.

5. The brightness of the flat panel display will be getting weaker as a result of frequent

usage. However, the operating period varies depending on the application environment.

6. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not

spray any liquid cleaner directly onto the screen. The MPC240 Series may come with or

w/o a touchscreen. Although the touchscreen is chemical resistant, it is recommended

that you spray the liquid cleaner on a cloth first before wiping the screen. In case your

system comes without the touchscreen, you must follow the same procedure and not

spray any cleaner on the flat panel directly.

7. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen may

cause malfunction or internal failure to the touchscreen.

8. The flat panel display is not susceptible to shock or vibration. When assembling the

MPC240 Series, make sure it is securely installed.

9. Do not leave this equipment in an uncontrolled environment where the storage

temperature is below -30°C or above 60°C. It may damage the equipment.

10. External equipment intended for connection to signal input/out or other connectors shall

comply with relevant IEC standard.

11. Do not open the system’s back cover. If opening the cover for maintenance is a must,

only a trained technician is allowed to do so. Integrated circuits on computer boards are

sensitive to static electricity. To avoid damaging chips from electrostatic discharge,

observe the following precautions:

Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help to discharge any static

electricity on your body.

When handling boards and components, wear a wrist-grounding strap, available

from most electronic component stores.

Important Safety Instructions

Read before operating equipment.

This product was designed and manufactured to meet strict quality and safety standards.

There are, however, some installation and operation precautions which you should be

particularly aware of.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Classification Class I ME Equipment.

6. External power adapter, Input : 100~240Vac, 135W

7. The medical panel computer is certified with medical certifications to meet medical grade

approval standards. This design and against enclosure allow it to operate reliably and

quietly, it applied in any medical environments.

8. WARNING: To avoid risk of electric shock, this equipment must only be connected to a

supply mains with protective earth.

9. Accessory equipment connected to the analog and digital interfaces must be in

compliance with the respective nationally harmonized IEC standards (i.e. IEC 60601-1

for medical equipment, IEC 60950-1 for ITE equipment). Furthermore all configurations

shall comply with the system standard in IEC 60601-1. Anyone who connects additional

equipment to the signal input part or signal output part is configuring a medical system,

and is therefore, responsible that the system complies with the requirements of the

system standard IEC 60601-1.

10. Power supply is specified as a part of ME EQUIPMENT.

11. For pluggable equipment, the mains connector shall be installed near the equipment and

shall be easily accessible.

12. Follow the national requirement to dispose unit/accessories/waste products/residues etc.

13. WARNING: Do not modify this equipment without authorization of the manufacturer.

14. WARNING: The operator must not touch the connectors and the patient at the same

time.

Classification

1. Degree of production against electric shock: Not classified.

2. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air

or with oxygen or nitrous oxide.

3. Mode of operation: Continuous.

4. Type of protection against electric shock: Class I equipment.

General Cleaning Tips

You may need the following precautions before you begin to clean the computer. When you

clean any single part or component for the computer, please read and understand the details

below fully.

1. When you need to clean the device, please rub it with a piece of dry cloth.

2. Be cautious of the tiny removable components when you use a vacuum cleaner to

absorb the dirt on the floor.

3. Turn the system off before you start to clean up the component or computer.

4. Never drop the components inside the computer or get circuit board damp or wet.

5. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of

cleaning. Some individuals may be allergic to the ingredients.

6. Try not to put any food, drink or cigarette around the computer.

vii

Cleaning Tools

Although many companies have created products to help improve the process of cleaning your

computer and peripherals, users can also use household items to clean their computers and

peripherals. Below is a listing of items you may need or want to use while cleaning your

computer or computer peripherals.

Keep in mind that some components in your computer may only be able to be cleaned using a

product designed for cleaning that component, if this is the case it will be mentioned in the

cleaning.

Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although

paper towels or tissues can be used on most hardware as well, we still recommend you

to rub it with a piece of cloth.

Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or

rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the

plastics parts.

Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of

a computer can be one of the best methods of cleaning a computer. Over time these

items can restrict the airflow in a computer and cause circuitry to corrode.

Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools

for wiping hard to reach areas in your keyboard, mouse, and other locations.

Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs.

NOTE: We strongly recommend that you should shut down the system before you start to

clean any single components.

Please follow the steps below:

1. Close all application programs.

2. Close operating software.

3. Turn off power switch.

4. Remove all devices.

5. Pull out power cable.

viii

Scrap Computer Recycling

If the computer equipments need the maintenance or are beyond repair, we strongly

recommend that you should inform your Axiomtek distributor as soon as possible for the

suitable solution. For the computers that are no longer useful or no longer working well, please

contact your Axiomtek distributor for recycling and we will make the proper arrangement.

Trademarks Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.

AMI is trademark of American Megatrend Inc.

IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.

Intel®and Pentium®are registered trademarks of Intel Corporation.

Other brand names and trademarks are the properties and registered brands of their

respective owners.

Table of Contents

Disclaimers......................................................................................................i

Disclaimers.....................................................................................................ii

CAUTION ........................................................................................................ii

Symbol Index.................................................................................................iii

Safety Precautions........................................................................................iv

Important Safety Instructions .......................................................................v

Classification.................................................................................................vi

General Cleaning Tips ..................................................................................vi

Cleaning Tools .............................................................................................vii

Scrap Computer Recycling........................................................................viii

Chapter 1 Introduction............................................. 1

1.1 Features...............................................................................................1

1.2 Specifications......................................................................................2

1.3 Dimensions..........................................................................................5

1.4 I/O Outlets............................................................................................6

1.5 Package Checklist.............................................................................10

Chapter 2 Starting MPC240....................................... 11

2.1 Turning On Your Device....................................................................12

2.2 Turning Off Your Device....................................................................13

2.3 Operating Your All-in-One PC ..........................................................14

2.3.1 Basic Operations....................................................................................... 14

2.3.2 Using the Optical Disk Drive ..................................................................... 17

2.3.3 Making Connections.................................................................................. 18

2.3.4 Using the Card Reader ............................................................................. 21

2.3.5 Using the Cable Tie................................................................................... 22

2.3.6 Connecting to Bluetooth Devices.............................................................. 23

2.3.7 Connecting to Internet............................................................................... 25

Chapter 3 Hardware Installation ........................... 29

3.1 Installing CPU/DRAM/WIFI module..................................................29

3.2 Installing Hard Disk Drive.................................................................33

3.3 Mounting............................................................................................34

Chapter 4 BIOS Setup Utility ................................. 35

4.1 BIOS Setup Menu..............................................................................35

4.2 Navigating and Entering Information in BIOS ................................36

4.3 Main Menu..........................................................................................37

4.4 Advanced Menu.................................................................................38

4.5 Boot Menu..........................................................................................39

4.6 Security Menu....................................................................................40

4.7 Save & Exit Menu ..............................................................................41

Appendix A Note........................................................ 43

Appendix B EMC Statement ...................................... 45

Table des matières

Autres manuels AXIOMTEK Écran tactile

AXIOMTEK

AXIOMTEK P1177S-871 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT-3100T Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-502-PCT Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT-5571TL-621 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT-3106TL-830 Manuel utilisateur

AXIOMTEK

AXIOMTEK MPC103-845 Manuel utilisateur

AXIOMTEK

AXIOMTEK MPC170-831-DC Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT107W-319 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT615-801 Manuel utilisateur

AXIOMTEK

AXIOMTEK PANEL1173-841 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT3126T-832 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-502-PCT/FR Manuel utilisateur

AXIOMTEK

AXIOMTEK P1177E-842 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT815L-511 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT815-834 Manuel utilisateur

AXIOMTEK

AXIOMTEK PANEL1127-671 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT3126T-834 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT315WL-845-PCT Manuel utilisateur

AXIOMTEK

AXIOMTEK P1127E-500 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT3187W-834-PCT Manuel utilisateur

AXIOMTEK

AXIOMTEK IFO2225-851 Series Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT3187W-832-PCT Manuel utilisateur

AXIOMTEK

AXIOMTEK P1157S-881 Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT318A-ELK-WCD Manuel utilisateur

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

Advantech

Advantech TPC-30 Series Manuel utilisateur

B&R Industries

B&R Industries MAPPC900-ENG Manuel utilisateur