AXIOMTEK TEN100 Series Manuel utilisateur
iv
TEN100 Series
Industrial Unmanaged 4-port
10/100BASE-TX and 1-port
100BASE-FX Ethernet Switch
User’s Manual
ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness, or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without
the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery and dispose of used ones.
©Copyright 2023 Axiomtek Co., Ltd.
All Rights Reserved
September 2023, Version A1
Printed in Taiwan
iii
Table of Contents
Disclaimers .................................................................................................................................ii
Section 1 Preface .................................................... 1
Section 2 Block Diagram......................................... 3
Section 3 Dimensions.............................................. 4
Section 4 Product Overview.................................... 5
4.1 Industrial Ethernet Switch............................................................................................. 5
4.2 Package Contents ........................................................................................................ 5
4.3 Product Highlights......................................................................................................... 6
4.3.1 Basic Features ............................................................................................ 6
4.4 Front Panel Display ...................................................................................................... 7
4.4.1 Power Status (PWR) ................................................................................... 7
4.4.2 Port Status LEDs......................................................................................... 7
4.5 Physical Ports ............................................................................................................... 8
Section 5 Installation .............................................. 9
5.1 Selecting a Site for the Switch...................................................................................... 9
5.2 DIN Rail Mounting......................................................................................................... 9
5.2.1 Assembly, Startup, and Dismantling ......................................................... 10
5.3 Connecting to Power .................................................................................................. 10
5.3.1 DC Terminal Block Power Inputs............................................................... 10
5.4 Connecting to Your Network ........................................................................................11
5.4.1 Cable Type & Length..................................................................................11
5.4.2 Cabling ...................................................................................................... 12
Section 6 Specifications ....................................... 13
Appendix A Connector Pinouts................................. 15
iv
This page is intentionally left blank.
TEN100-0500-i Series User’s Manual
Preface 1
Section 1
Preface
A member of the growing family of rugged switches, this switch addresses a need for a
smaller switch. This switch provides an affordable solution for rugged and outdoor
environment, transportation road-side cabinet, industrial floor shop, multitenant dwellings or
Fiber To The Home (FTTH) applications. Capable of operating at temperature extremes of
-10°C to +60°C, this is the switch of choice for harsh environments constrained by space.
Plug-and-Play Solution:
The switch is a plug-and-play Fast Ethernet Switch in compact size. It doesn't have any
complicated software to set up.
This manual describes how to install and use the Industrial Ethernet Switch. This switch
integrates full wire speed switching technology. This switch brings the answer to complicated
hardened networking environments.
To get the most out of this manual, you should have an understanding of Ethernet networking
concepts.
In this manual, you will find:
Features on the switch
Illustrative LED functions
Installation instructions
Specifications
TEN100-0500-i Series User’s Manual
2 Preface
This page is intentionally left blank.
TEN100-0500-i Series User’s Manual
Block Diagram 3
Section 2
Block Diagram
TEN100-0500-i Series User’s Manual
4 Dimensions
Section 3
Dimensions
TEN100-0500-i Series User’s Manual
Product Overview 5
Section 4
Product Overview
4.1 Industrial Ethernet Switch
4.2 Package Contents
When you unpack the product package, you shall find the items listed below. Please inspect
the contents, and report any apparent damage or missing items immediately to your
authorized reseller.
🗸This Switch
🗸User’s Manual
TEN100-0500-i Series User’s Manual
6 Product Overview
4.3 Product Highlights
4.3.1 Basic Features
⚫Complies with EN61000-6-2 & EN61000-6-4 EMC Generic standard immunity for
industrial environment.
⚫Supports IEEE802.3az 10Base-Te only. 10Base-T is not supported. 10Base-Te is
fully interoperable with 10Base-T over 100m of class D (Category 5) or better cabling
as specified in ISO/IEC 11801:1995.
⚫Supports 802.3az/802.3u/802.3x. Auto-negotiation: 10/100Mbps, Full/Half-duplex.
Auto MDI/MDIX.
⚫100Base-FX: Multi mode SC or ST type, Single mode SC or ST type.
⚫100Base-BX: WDM Multi mode or Single mode SC type.
⚫Supports 1024 MAC addresses, 448K bits buffer memory.
⚫IEEE802.3x Flow control for Full-duplex, Back pressure for Half-duplex.
⚫None-blocking architecture and full wire-speed forwarding rate.
⚫Supports IEEE802.1p QoS with two priority queues.
◼Untagged packets with low priority.
◼Output Queue Scheduling: High priority packet rate is 8 packets.
◼Two-priority queue based on CoS field value:
CoS Field Value
Priority
0, 1, 2, 3
Low
4, 5, 6, 7
High
⚫Supports IEEE802.3az Energy Efficient Ethernet (EEE).
⚫Supports Max. length of frame up to 1552 Bytes.
⚫Power consumption: 2.12W Max.
⚫Power Supply: DC Terminal Block power input, 12-48VDC.
⚫Operating temperature ranges from -10°C to 60°C (14°F to 140°F)
⚫Plastic compact DIN-Rail industrial case design
Autres manuels pour TEN100 Series
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels AXIOMTEK Changer
