AXIOMTEK NA-814 Manuel
NA-814
Hardware Installation Guide
For service person only
ii
Disclaimers
The information in this manual has been carefully checked and is
believed to be accurate. AXIOMTEK Co., Ltd. assumes no
responsibility for any infringements of patents or other rights of third
parties, which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may
be contained in this document.AXIOMTEK makes no commitment to
update or to keep current the information contained in this manual.
AXIOMTEK reserves the right to make improvements to this
document and/or product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission ofAXIOMTEK Co., Ltd.
Copyright 2006 by AXIOMTEK Co., Ltd.
All rights reserved.
Version A1 November 2006
Printed in Taiwan
iii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.
iv
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
2. Disconnect the power cords from the NA-814 before making any
installation. Be sure both the system and the external devices are
turned OFF. Sudden surge of power could ruin sensitive
components. Make sure the NA-814 is properly grounded.
3. Do not open the system’s top cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do
so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
9Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity on
your body.
9When handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Other brand names and trademarks are the properties of their
respective owners.
v
Table of Contents
Disclaimers...................................................................................ii
FCC Compliance.........................................................................iii
Chapter 1..............................................................................................1
1.1 General Description............................................................1
1.2 Standard Features..............................................................2
1.3 System Specifications.........................................................2
1.3.1 Hardware .................................................................2
1.4 Dimensions.........................................................................5
1.5 Front Panel Outlets.............................................................6
1.6 Rear Panel Outlets .............................................................7
Chapter 2..............................................................................................9
2.1 Preinstallation Checklist .....................................................9
2.2 Board Placement............................................................. 10
2.3 Connectors and Jumpers .................................................11
2.3.1 Connectors ............................................................11
2.3.2 Jumper Settings ...................................................... 12
2.4 Setting up the appliance.................................................. 15
2.4.1 Removing and Replacing the Top Cover.............. 15
2.4.2 Installing a Microprocessor (CPU)........................ 15
2.4.3 Installing a memory module (DIMM)....................... 18
2.4.4 Installing a DMA33/66/100 hard drive .................. 18
2.4.5 Install Riser Card..................................................... 19
2.4.6 Installing Display Interface.................................... 19
2.4.7 Installing Serial Port Interface............................... 19
2.4.8 Installing Keyboard and PS/2 Mouse Connectors 20
2.4.9 Installing USB Connector........................................ 20
vi
2.4.10 Installing and Program LCD Module..................... 21
Chapter 3........................................................................................... 24
3.1 BIOS Introduction ............................................................ 24
3.2 BIOS Setup...................................................................... 24
3.3 Standard CMOS Setup.................................................... 26
3.4 Advanced BIOS Features................................................ 29
3.5 Advanced Chipset Features............................................ 34
3.6 Integrated Peripherals..................................................... 35
3.7 Power Management Setup.............................................. 38
3.8 PNP/PCI Configuration.................................................... 40
3.9 PC Health Status............................................................. 43
3.10 Load Optimized Defaults................................................. 44
3.11 Set Supervisor/User Password........................................ 45
3.12 Save & Exit Setup............................................................ 48
3.13 Quit Without Saving......................................................... 49
Appendix A......................................................................................... 51
NA-814 Hardware Installation Guide
Introduction 1
Chapter 1
Introduction
This chapter contains the general information and the detailed specifications
of the NA-814 NetworkAppliance server. Chapter 1 includes the following
sections:
1.1 General Description
NA-814 server is designed for network software solution providers those
have data secure, voice over IP, video streaming, network bandwidth
controller and another networking appliance requirements across this stable
and reliable multiple LAN device.
It is a reliable and affordable, 1U-height unit that requires only power and
network connections for setup. There can be deployed up to four LAN ports
combinations for customer selection in the maximum for application.
NA-814 Hardware Installation Guide
Introduction
2
NA-814 has pretty good enclosure management interface to be
implemented in the factory default. It can support P.O.S.T (Power on Self
Test) feature through hyper-terminal by console port. LCD module function is
available for customer coding also.
And it has room space for one hard drive deployment. Customer can
implement system log and monitoring functions through this hardware
specification. With its innovative mechanical and electrical design, NA-814
server provides one PCI expansion slot for VPN encryption / decryption adapter
board and another special functions enabling. It cans enhancement network
security process performance and of-load the CPU loading.
NA-814 can support wonderful networking application platform by excellent cost
with performance ratio.
1.2 Standard Features
z1U-height rack-mount/stacked-up design
zHigh performance Intel Pentium 4, Pentium D, Celeron D
processors (LGA775-Pin)
zFour 10/100 Ethernet LAN ports combinations are for NA-814.
zSupport two RS-232(one DB9 and one pin header) and six
USB(two connectors and two 2*5 box headers)
zPCI 32-bit/33MHz expansion slot and one Mini-PCI slot for
another network security encryption board
zLCM setting functions is available
zSupports Redhat Linux 2.4 and 2.6 kernel
1.3 System Specifications
1.3.1 Hardware
zForm Factor:
1U rack-mount/stacked-up on desktop design
zCapacity:
It is from 0 to 250GB and beyond, depending on the 2.5” hard disk
drive capacity.
NA-814 Hardware Installation Guide
Introduction 3
zPower Supply:
Single 300W ATX HRP power supplies
Standard ATX power input connector
zHard Drive:
Spacing for 1 x IDE HDD (2.5”)
zFront Panel Connector:
4 x 10/100 Ethernet LAN port w/LED
1 x Console port
2 x USB port
zFront Panel LED:
1 x LED for HDDs
1 x Power LED for System
zProcessor:
IntelPentium4 processor up to 3.8GHz, Pentium D, Celeron
D processors LGA 775 Pin,
FSB 800MHz
zChipset:
Intel 82865G FSB 533/800 MHz w/ICH5
zBIOS:
Award 4MB Flash BIOS Plug & Play
zL2 Cache:
Built-in in CPU
zMain Memory:
Two DDR266/DDR333/DDR400 memory DIMM can be up to
2GB in the maximum
zIDE Interface:
Support two ATA 33/66/100 EIDE channels
Support two channels for S-ATA(Option)
zEthernet:
Totally has four 10/100 Ethernet LAN port connections are
available.
zExpansion:
One PCI 32-bit/33MHz, One Mini-PCI connector for security
encryption card or other third-party cards expansion.
NA-814 Hardware Installation Guide
Introduction
4
zCompact-FlashTM:
One IDE interface CompactFlash socket for embedded use.
zLink/Active LED (Single color)for LAN port #1, port#2, port#3 and
port#4
1. The yellow LED is on when there is an active connection on
the LAN port.
2. The LED flashes when there is transmit or receive activity to
or from the appliance.
3. The LED is dark when it off line.
zDimensions:
427.9mm (W) x 44mm (H) x 301mm (D)
zOperation environment:
Air temperature: 0° C – 40°C
Humidity: 5% – 95%
Table des matières
Autres manuels AXIOMTEK Serveur
AXIOMTEK
AXIOMTEK NA-1301 Manuel
AXIOMTEK
AXIOMTEK NA362 Manuel utilisateur
AXIOMTEK
AXIOMTEK IRU131 Manuel utilisateur
AXIOMTEK
AXIOMTEK NA-401 Manuel
AXIOMTEK
AXIOMTEK NA-810A Manuel
AXIOMTEK
AXIOMTEK NA-806D Manuel
AXIOMTEK
AXIOMTEK NA-100 Instructions de montage
AXIOMTEK
AXIOMTEK NA-550 Series Manuel utilisateur
AXIOMTEK
AXIOMTEK NA150 Manuel utilisateur
AXIOMTEK
AXIOMTEK AX62140TP-P4 Manuel utilisateur
