Axiometrix Solutions Imc EOS Manuel utilisateur

imcTest & Measurement GmbH • Voltastr.5 • 13355Berlin • Germany

imc EOS

Manual

Edition 4 - 2022-07-13

Page 2

This documentation is the intellectual property of imcTest & Measurement GmbH. imcTest &

Measurement GmbH reserves all rights to this documentation. The applicable provisions are stipulated in

the "imc Software License Agreement".

The software described in this document may only be used in accordance with the provisions of the "imc

Software License Agreement".

Open Source Software Licenses

Some components of imc products use software which is licensed under the GNU General Public License

(GPL). Details are available in the About dialog.

A list of the open source software licenses for the imc measurement devices is located on the

imcSTUDIO/imcWAVE installation medium in the folder "Products\imc DEVICES\OSS" or "Products\imc

DEVICEcore\OSS". If you wish to receive a copy of the GPL sources used, please contact our Hotline.

Disclaimer of liability

The contents of this documentation have been carefully checked for consistency with the hardware and

software systems described. Nevertheless, it is impossible to completely rule out inconsistencies, so that we

decline to offer any guarantee of total conformity.

We reserve the right to make technical modifications of the systems.

Page 3

TableofContents

1 General introduction ................................................................................................. 5

1.1 imc Customer Support / Hotline .................................................................................................... 5

1.2 Legal notices ................................................................................................................................... 5

1.3 Notes regarding this document ..................................................................................................... 8

1.4 Explanation of symbols .................................................................................................................. 9

1.5 Last changes in content ................................................................................................................ 10

2 Safety ...................................................................................................................... 11

3 Product overview .................................................................................................... 14

3.1 imc EOS ......................................................................................................................................... 14

3.2 Mechanical dimensions and drawings ......................................................................................... 15

3.3 Included accessories ..................................................................................................................... 16

3.4 Optional accessories ..................................................................................................................... 16

4 Assembly and connection ........................................................................................ 17

4.1 After unpacking… ......................................................................................................................... 17

4.2 Before commissioning .................................................................................................................. 18

4.3 Notes on connecting the device .................................................................................................. 18

4.4 Click mechanism ........................................................................................................................... 26

4.5 Powering on ................................................................................................................................. 27

4.6 Powering off ................................................................................................................................. 27

5 Indicators and fault detectors (LEDs) ....................................................................... 28

5.1 Operational readiness .................................................................................................................. 28

5.2 Troubleshooting / Restart ............................................................................................................ 29

6 Maintenance and servicing ...................................................................................... 29

6.1 Maintenance and servicing notes ................................................................................................ 29

6.2 Cleaning ........................................................................................................................................ 29

6.3 Storage ......................................................................................................................................... 30

6.4 Transport ...................................................................................................................................... 30

7 Start of operation Software / Firmware ................................................................... 30

7.1 Installation - Software .................................................................................................................. 30

7.2 Connect the device ....................................................................................................................... 31

7.3 Connecting via LAN in three steps ............................................................................................... 32

7.4 Firmware update .......................................................................................................................... 35

8 imc EOS properties .................................................................................................. 36

8.1 Analog inputs ................................................................................................................................ 36

8.2 Operating software ...................................................................................................................... 38

8.3 Starting measurement ................................................................................................................. 40

8.4 imc EOS in a compound assembly ................................................................................................ 42

8.5 Synchronization ............................................................................................................................ 43

9 Equipment options .................................................................................................. 43

Page 4

TableofContents

10 Technical Specs ...................................................................................................... 44

10.1 imc EOS U-4 ................................................................................................................................ 45

Index .......................................................................................................................... 52

Page 5

imc Customer Support / Hotline

1 General introduction

1.1 imc Customer Support / Hotline

If you have problems or questions, please contact our Customer Support/Hotline:

imcTest & Measurement GmbH

Hotline

(Germany):

+49 30 467090-26

E-Mail:

hotline@imc-tm.de

Internet:

https://www.imc-tm.com

International partners

For our international partners see https://www.imc-tm.com/distributors/.

Tip for ensuring quick processing of your questions:

If you contact us you would help us, if you know the serial number of your devices and the version info of the

software. This documentation should also be on hand.

The device's serial number appears on the nameplate.

The program version designation is available in the About-Dialog.

1.2 Legal notices

Quality Management

imcTest & Measurement GmbH holds DIN-EN-ISO-9001 certification

since May 1995. You can download the CE Certification, current

certificates and information about the imc quality system on our website:

https://www.imc-tm.com/quality-assurance/.

imc Warranty

Subject to the general terms and conditions of imcTest & Measurement GmbH.

Liability restrictions

All specifications and notes in this document are subject to applicable standards and regulations, and reflect the

state of the art well as accumulated years of knowledge and experience. The contents of this document have

been carefully checked for consistency with the hardware and the software systems described. Nevertheless, it

is impossible to completely rule out inconsistencies, so that we decline to offer any guarantee of total

conformity. We reserve the right to make technical modifications of the systems.

The manufacturer declines any liability for damage arising from:

failure to comply with the provided documentation,

inappropriate use of the equipment.

Please note that all properties described refer to a closed measurement system and not to its individual slices.

Page 6

Chapter 1 General introduction

Guarantee

Each device is subjected to a 24-hour "burn-in" before leaving imc. This procedure is capable of detecting almost

all cases of early failure. This does not, however, guarantee that a component will not fail after longer operation.

Therefore, all imc devices are granted liability for a period of two years. The condition for this guarantee is that

no alterations or modifications have been made to the device by the customer.

Unauthorized intervention in the device renders the guarantee null and void.

Notes on radio interference suppression

imc EOS devices satisfy the EMC requirements for an use in industrial settings.

Any additional products connected to the product must satisfy the EMC requirements as specified by the

responsible authority (within Europe1) in Germany the BNetzA - "Bundesnetzagentur" (formerly BMPT-Vfg. No.

1046/84 or No. 243/91) or EC Guidelines 2014/30/EU. All products which satisfy these requirements must be

appropriately marked by the manufacturer or display the CE certification marking.

Products not satisfying these requirements may only be used with special approval of the regulating body in the

country where operated.

All lines connected to the imc EOS devices should not be longer than 30m and they should be shielded and the

shielding must be grounded.

Note

The EMC tests were carried out using shielded and grounded input and output cables with the exception of

the power cord. Observe this condition when designing your experiment to ensure high interference

immunity and low jamming.

1 If you are located outside Europe, please refer the appropriate EMC standards used in the country of operation.

Cables and leads

In order to comply with the value limits applicable to Class B devices according to part 15 of the FCC regulations,

all signal leads connected to imc EOS must be shielded..

Unless otherwise indicated, no connection leads may be long leads (<30m) as defined by the standard IEC

61326-1. LAN-cables (RJ 45) and CAN-Buscables (DSUB-9) are excepted from this rule.

Only cables with suitable properties for the task (e.g. isolation for protection against electric shock) may be

used.

ElektroG, RoHS 2, WEEE, CE

The imcTest & Measurement GmbH is registered with the authority as follows:

WEEE Reg. No. DE 43368136

valid from 24.11.2005

Reference

https://www.imc-tm.com/elekrog-rohs-weee/ and https://www.imc-tm.com/ce-conformity/

Page 7

Legal notices

FCC-Notice

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult our imc Hotline or an experienced technician for help.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this product that are not

expressly approved by imc may void the user's authority to operate this equipment.

Page 8

Chapter 1 General introduction

1.3 Notes regarding this document

This document provides important notes on using the device / the module. Safe working is conditional on

compliance with all safety measures and instructions provided. The manual is to be used as a kind of reference

book. You can skip the description of the modules you do not have.

Additionally, all accident prevention and general safety regulations pertinent to the location at which the device

is used must be adhered to.

These instructions exclusively describe the device, not how to operate it by means of the software!

If you have any questions as to whether you can set up the device / module in the intended environment, please

contact the imc hotline. The measurement system has been designed, manufactured and unit-tested with all due

care and in accordance with the safety regulations before delivery and has left the factory in perfect condition.

In order to maintain this condition and to ensure safe operation, the user must observe the notes and warnings

contained in this chapter and in the specific sections applicable to the concrete device. Never use the device

outside the specification!

This will protect you and prevent damage to the device.

Special notes

Warning

Warnings contain information that must be observed to protect the user from harm or to prevent damage

to property.

Note

Notes denote useful additional information on a particular topic.

Reference

A reference in this document is a reference in the text to another text passage.

Please help us to improve our documentation:

Which terms or descriptions are incomprehensible?

What additions and enhancements you suggest?

Where have material mistakes slipped in?

Which spelling, translation or typing errors have you found?

Page 9

Explanation of symbols

1.4 Explanation of symbols

Potential compensation

Connection for potential compensation

Grounding

Connection for grounding (general, without protective function)

Protective connection

Connection for the protective conductor or grounding with protective function

No household waste

Please do not dispose of the electrical/electronic device with household waste, but at the

appropriate collection points for electrical waste, see also chapter 1.2 .

CE Conformity

see CE chapter 1.2

Attention! General danger zone!

This symbol indicates a dangerous situation;

Since there is insufficient space for indicating the rated quantity at the measuring inputs,

refer to this manual for the rated quantities of the measuring inputs before operation.

Possibility of electric shock

The warning generally refers to high measurement voltages or signals at high potentials and

is located on devices suitable for such measurements. The device itself does not generate

dangerous voltages.

DC, Direct Current

Supply of the device via a DC voltage source (in the specified voltage range)

RoHS of the PR China

The limits for hazardous substances in electrical/electronic equipment applicable in the PRC

are identical to those in the EU. The restrictions are complied with (see chapter 1.2 ). A

corresponding "China-RoHS" label is omitted for formal/economic reasons. Instead, the

number in the symbol indicates the number of years in which no hazardous substances are

released. (This is guaranteed by the absence of named substances).

Observe the documentation

Read the documentation before starting work and/or operating.

Page 10

Chapter 1 General introduction

1.5 Last changes in content

Please help us to improve our documentation:

Which terms or descriptions are incomprehensible?

What additions and enhancements you suggest?

Where have material mistakes slipped in?

Which spelling, translation or typing errors have you found?

Responses and other feedback should be directed to the Hotline .

History:

Amendments and bug-fix in manual edition 3

Chapter

Amendment

Symbols

Missing symbols added in chapter "Explanation of symbols".

Connecting via LAN

The dialog for configuring the IP address of the device also provides the IP address of

the PC. Thus, the first step was removed from the documentation, which presented

different possibilities in Windows to determine the IP address.

Technical Specs

We updated the general introduction to this chapter.

Amendments and bug-fix in manual edition 2.2

Chapter

Amendment

Technical Specs

All available measurement ranges are now stated for the offset error.

Amendments and bug-fix in manual edition 2.1

Chapter

Amendment

Precautions for

operation

reference for standard operating orientation of imc EOS added

Amendments and bug-fix in manual edition 2

Chapter

Amendment

Dimensions

Standard operating orientation of the device added

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Axiometrix Solutions Matériel réseau

Axiometrix Solutions

Axiometrix Solutions imc ARGUSfit Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur

Axiometrix Solutions imc EOS Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques