Avery Weigh-Tronix TT-830 Manuel utilisateur
TT-830 Bench Scale
User’s Manual
2TT-830 Bench Scale User’s Manual
July 2008 830_U.P65 PN 29737-0017 Issue AD Printed in USA
Risk of electrical shock. Do not remove cover. No user service-
able parts inside. Refer servicing to qualified service personnel.
Weigh-Tronix reserves the right to change
specifications at any time.
CAUTION
EUROPEAN COUNTRIES
WARNING
This is a Class A product. In a domestic environment this product may cause radio
interference in which the user may be required to take adequate measures.
3
TT-830 Bench Scale User’s Manual
Table of Contents
Table of Contents .....................................................................................3
Specifications............................................................................................4
Introduction ...............................................................................................5
About This Manual ..........................................................................5
TT-830 Bench Scale .................................................................................5
TT-830 Front Panel.........................................................................5
Main Display.........................................................................6
Front Panel Keys..................................................................6
Hard Keys..................................................................6
Soft Keys ...................................................................7
Weighing Operation ........................................................................8
Pushbutton Tare Operation..................................................8
Keypad Tare Entry ...............................................................8
Specialized Operations ................................................................... 9
Accessing Program Serial#.............................................................9
Pages are numbered consecutively beginning with the cover page.
4TT-830 Bench Scale User’s Manual
Power Input
Operational Keys
Operational Annunciators
Display
Display rate
A to D Conversion Rate
Unit of Measure
Capacity Selections
Incremental Selections
Displayed Resolution
Audio Output
Time and Date
Internal Resolution
Harmonizer™digital filtering:
Standard input and outputs:
Available Options
Operating Temperatures
Dimensions
Weight
Agencies
Warranty
115 Volts AC, 50/60 Hz single phase
Optional 230 Volts AC, 50/60 Hz single phase
Zero, Tare, Print, Units, Select, Enter, Escape, Clear, 0-9,
Decimal Point and Five Soft Keys labeled per selected operational routine.
Displayed symbols indicate motion, center of zero, unit of measure and more.
5" W x 1.33" H dot matrix LCD, cold cathode flourescent backlight (240 X 64
dot layout)
Selectable, 0.1 to maximum readable updates
60 times per second
Pounds, kilograms, grams, ounces, pounds and ounces and two selectable
custom units
10 (5); 50 (25); 100 (50); lbs (kg)
Multiples and sub multiples of 1, 2, 5
NTEP pending at 10,000d / configurable
Audio tone for key contact assurance or operational alarms
Battery protected real time clock is standard
1,000,000 counts analog, QuartzellTM transducer = 2,000,000
Fully programmable to ignore noise and vibration
Four communications choices:
Com 1: RS232, RS-485/422
Com 2: RS232, 20 mA current loop
(One bi-directional signal per port)
- DC operation at 10 to 32 VDC, 3.5 Amp
- OPTO 22 I/O Modules
- Remote Expanded Control Interface for 8, 16, 24, or 32 OPTO 22 I/O Mod-
ules
- Alpha-numeric, PC style serial keyboard
14 to 104° F (-10 to 40° C), 10 to 90% relative humidity
Platform: 12" x 14" (50- and 100-lb models)
Platform: 8.5" dia. (10-lb models)
Overall: 14" W x 17" D x 4.5" H (35.6cm W x 43.2cm D x 11.4cm H)
18.5 lb, 8.4 kg
UL/CUL pending
CE pending
NTEP pending
2 year
Specifications
5
TT-830 Bench Scale User’s Manual
About This Manual
Introduction
TT-830 Bench Scale
Figure 1
TT-830 Front Panel
This manual covers the information you need to understand the operation of
your Table Top 830 (TT-830) bench scale.
Major sections of this manual are headed by titles in a black bar like Intro-
duction above. Subheadings appear in the left column. Instructions and text
appear on the right side of the page. Occasionally notes, tips, and special
instructions appear in the left column.
The TT-830 is a completely programmable table top scale with a QuartzellTM
weight sensor. See the Specifications for a complete list of standard fea-
tures.
The TT-830 front panel is shown in Figure 1.
The front panel includes the following:
• 240 x 64 dot matrix LCD display with cold cathode fluorescent back-
light
• Five variable function soft keys
• Numeric keypad
• SELECT key
• UNITS key
• PRINT key
• TARE key
• ZERO key
• CLEAR key
• ESCAPE key
• ENTER key
• Decimal point key
TT-830 Front Panel
6TT-830 Bench Scale User’s Manual
The main display is a 240 x 64 dot matrix LCD display with cold cathode
fluorescent backlight. It can display graphics, words and numbers. This
flexibility allows graphics and alphanumeric characters to be displayed at the
same time. There are 33 displays available on the TT-830. See the Service
Manual for all the examples. Your system will be configured for your particu-
lar needs. The screen you see will depend on what weighing application you
are performing.
The keys on the front panel of the TT-830 are of two types, hard keys and
soft keys. Hard keys are labeled directly and soft key labels appear on the
display. Soft keys (F1-F5) function differently at different times and their
labels appear on the main display and they change as needed.
Below are brief descriptions for each of the hard key functions:
Repeatedly press the SELECT key to scroll through the
available weight reading displays. (Examples - gross, net,
tare, minimum, maximum, etc.)
Press the UNITS key to scroll through the available units of
measure.
Press the PRINT key to send data to a connected printer.
Press the TARE key to enter a tare weight, then press
SELECT to see the net display mode.
Press the ZERO key to establish a zero reference. A
center-of-zero icon will be displayed. During motion an M
will appear below the center-of-zero icon.
Press the ESCAPE key to back out of menus or cancel a
numeric entry without accepting the value.
Press the CLEAR key to clear values from the display.
See note at left.
Press the ENTER key to enter a keyed in value or accept a
displayedchoice.
Press and hold the ON/OFF key for five seconds to turn the
unit off.
The numeric keypad is for entering numbers.
Front Panel Keys
Hard Keys
Main Display
To increase the contrast of the
display, press and hold the
CLEAR and 9 keys until the
desired contrast is reached. To
decrease contrast, press and
hold the CLEAR and 3keys.
7
TT-830 Bench Scale User’s Manual
Soft keys are so-called because their function is not fixed. Function can
change as mode of operations change or as the program for your particular
setup changes.
Their are five soft keys located directly below the display. If the keys are
needed during any operation, a label for each active key appears in the
display directly above. There are only five key labels available at one time
but this does not limit the potential usefulness of these keys. Programs can
be created to enable one key to access another level of operation with five
more key names and functions.
After unpacking the scale, place it on a level, stable surface. Plug it into an
appropriate power source. The outlet must be properly grounded and readily
accessible.
A new unit will power up ready to use. This scale is fully programmable. If
you have a custom program resident in your unit, it will power up with that
program active and ready to use.
Since custom programming is possible with this scale, the following pages
only cover basic weighing procedures available when you receive a factory
fresh scale.
To customize your unit you must write a program using the 830 SimPoserTM
software available from Weigh-Tronix and download it to the scale.
Soft Keys
Installing the TT-830
8TT-830 Bench Scale User’s Manual
The following instructions step you through a typical weighing operation:
1. Power up the indicator. If the
display mode is not the one you
want to use, repeatedly press
the SELECT key until the display
value you want (gross, net, etc.)
is displayed. . . Your indicator may be configured
with only one display value. Select-
ing other display values may not be
an option with your particular setup.
2. Zero the scale by pressing the
ZERO key. . . Display should read zero weight and
the center of zero symbol is dis-
played.
3. Place object to be weighed on
the scale. . . An Mappears on the display during
scale motion and the weight is
displayed.
To perform a tare operation with the TARE key, follow these instructions:
1. Zero the scale by pressing the
ZERO key. . . Display shows zero weight.
2. Place container to be tared on
the scale and press the TARE
key. . . The display changes to a NET
display and shows zero weight.
3. Place material to be weighed on
the scale. . . Net weight is displayed.
For entry of a known tare weight follow these instructions:
1. With the indicator showing gross
weight, key in the tare weight
using the numeric keys. . . A tare entry display shows the
weight that you key in.
2. Press ENTER to accept this tare
entry. . . The net weight is displayed in net
mode.
Weighing Operation
Pushbutton Tare Operation
Keypad Tare Entry
9
TT-830 Bench Scale User’s Manual
Due to the unlimited variety of applications available for the TT-830, it is not
practical to describe all the possible specialized operations in this manual.
Each application program will be unique.
Specialized operations will offer you soft key choices specific to the applica-
tion and will guide you with messages on the display.
The time may come when you are asked by a service technician for informa-
tion about your software program. There is a series of key strokes which will
bring that information to the screen. Below are the instructions:
1. Press and hold the ESCAPE key until the TT-830 beeps.
2. Within five seconds, key in the number 111 and press ENTER.
3. Press the soft key labeled VIEW.
4. Press the soft key labeled VERS. The information will appear on the
display.
Specialized Operations
Accessing Program
Information
Autres manuels pour TT-830
1
Table des matières
Autres manuels Avery Weigh-Tronix Échelle
Avery Weigh-Tronix
Avery Weigh-Tronix ZP900 Manuel d'instructions
Avery Weigh-Tronix
Avery Weigh-Tronix 7821 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix PC-805 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix RD40RF Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix HC12000 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix ZK840 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix PC-905 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix ZP900 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix PC-220 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix ZK830 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix PC-902 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix QC-3265 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix 3275 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix 1000 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix Brecknell B240 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix PC-802 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix PC-902 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix G235 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix ZM 110 Manuel utilisateur
Avery Weigh-Tronix
Avery Weigh-Tronix ZK840 Manuel utilisateur
