Avaya P120 SMON Manuel utilisateur
Avaya P120
Quick Start Guide
1. Unpack
2. Rack mount
3. Power up
4. Connect the Cables
5. Basic Configuration
6. Install Device Manager (optional)
1. Unpack
Check the package contents for the
following
• Avaya P120 Workgroup Switch
• Avaya P120 User’s Guide (on the CD)
• Quick Start Guide (this document)
• AC power cable
• RJ-45 to DB-9 serial adapter cable
• Four rubber feet
• Four screws with washers for rack
mounting
• Avaya P120 Standalone Manager CD
CD Contents
• Avaya P120 Standalone Manager
• Avaya P120 User’s Guide
• Avaya P120 Standalone Manager
User’s Guide
• Adobe® Acrobat® Reader (US
English)
Note: Ethernet connection cables are not
supplied
2. Rack mount
1. Snap open the ends of the front panel
to reveal the screw holes.
2. Position the unit in the rack.
3. Secure the unit to the rack, taking care
not to overtighten the screws.
4. Snap closed the hinged ends of the
front panel.
5. You can now safely connect cables to
the device.
Warning! Disconnect all cables from the switch before
proceeding with the rack installation!
Rack Mounting
3. Power up
1. Connect the supplied AC power cord
to the back panel power supply con-
nector (see Figure opposite).
2. Connect the other end of the AC
power cable to an AC power outlet
(120-240 VAC, 50/60 Hz).
3. The PWR LED lights to indicate
power is on, and the OPR LED lights
to indicate that the CPU has booted
up and is ready for operation.
4. Use the Left/Right buttons to select a
Function (see Figure below)
5. When a Function has been selected
the Port LEDs show the status of that
Function per port.
6. Connect the BUPS power cable (if
applicable) to the Avaya P120.
7. Connect the other end of the BUPS
cable to the Avaya P330 BUPS
Function LEDs
Port LEDs
Left/Right
and Reset (both)
Switches
FIV Switch
Avaya P120 LEDs
PWR – When ON, Internal power supply is active (Blink, Backup P.S. active)
OPR – When On, CPU boot operation complete (OFF, CPU is booting)
FIV – Force Initial Version (see the P120 User’s Guide)
LNK – When ON, link is OK
COL – When ON, indicates a collision on the port in HDX mode
Tx, Rx – When ON, shows traffic activity for transmitted and received packets
FDX – When ON, shows port is in Full duplex (Half duplex when OFF)
FC – When ON, Flow Control is enabled for a port in FDX mode
100M – When ON, the port is in Fast Ethernet (100M) mode (10BaseT when OFF)
G– When ON, the port is included in a Link Aggregation Group (LAG).
Avaya P120 Back Connectors
4. Connect the cables
Connect PCs. servers, routers, work-
stations, and hubs
1. Connect the appropriate Ethernet con-
nection cable (not supplied) to a
10/100 Mbps port on the front panel
of the Avaya P120.
You can use standard RJ-45 connec-
tions. You must use CAT-5 cable for
100 Mbps operation.
2. Connect the other end of the cable to
the Ethernet port of the PC, server,
router, workstation, switch or hub.
3. Check that the appropriate link (LNK)
LEDs light up.
Connect the console cable
1. Connect the supplied RJ-45 connector
to the connector marked “Console”
on the front panel of the Cajun P120.
2. Connect the other end of the cable to
a terminal or PC with terminal emula-
tion software installed.
5. Perform basic configu-
ration
To connect a PC terminal or VT-100
terminal to the Avaya P120
1. Connect the terminal or PC to the
console port on the P120 using the
supplied serial (RJ-45 to DB-9
adapter) cable.
2. Configure the serial port settings of
the PC as follows:
• 9600 Baud
• No parity
• 8 data bits
• 1 stop bit
• No flow control
3. If you are using a PC, initiate a
VT-100 terminal emulation session
using an application such as
HyperTerminal.
4. Press “Enter” several times until the
CajunP120> command prompt is
displayed.
Setting the Mandatory Parameters
If you wish to change the default parame-
ters shown on the opposite page and con-
figure the mandatory parameters, Avaya
recommends that you use the Command
Line Interface (CLI).
For further information, please refer to
Chapter 5 of the P120 User’s Guide.
To Establish a Telnet Session to the
Avaya P120 via the Network
1. Verify that the Avaya P120 and your
PC are on the same local network. If
the Avaya P120 is set with its default
IP address, then change the PC’s IP
address so that it will be on the same
subnet as the Avaya P120’s default
address (149.49.32.x). If you want to
use secure Telnet, the port to which
the PC is connected must be on the
same VLAN as the agent.
2. Click on Start>Settings>Control
Panel>Network from the Windows
taskbar.
3. Select TCP/IP from the list of
installed network components.
4. Click on Properties.
In the IP address Property Sheet,
enter the address 149.49.32.134 and
the net mask 255.255.255.0
5. Click on OK.
6. Connect a Avaya P120 front panel
port to your network.
7. Connect your PC to the network.
8. Start the Telnet session at the prompt
by typing telnet
<Cajun_P120_IP_address>
, e.g.,
telnet 149.49.32.134
9. Enter the Avaya P120 user-level pass-
word. The default is norm in lower
case letters (do not use uppercase).
The CajunP120> prompt will dis-
play when you have established com-
munications with the Avaya P120.
Default Switch Parameters
Default Port Parameters
Configuration Parameter Default Setting
Port Speed and Mode • 10/100M copper ports: auto-negotiation
• 100Base-FX ports: 100 full
Port Administration State Enabled
Port VLAN Tagging No tagging
Flow Control • 10/100 and 100 Mbps: Disabled
• 1000 Mbps: Autonegotiation
Port Mirroring Disabled
Early Packet Drop (HOLB-P) • 10/100T and 100F Mbps: Disabled
• 1000 Mbps: enabled
Link Aggregate Grouping (LAG) None
Redundant Link None
Duplex Mode • 10/100 Mbps ports: auto
• 100 Mbps fiber ports: full
• 1000 Mbps ports: full
Port Priority Regular
Port Security Not secured
Configuration Parameter Default Setting
Avaya P120 IP Address 149.49.32.134
BootP Mode Never
Default Gateway 0.0.0.0
SLIP IP Address 192.168.10.1
Management PC SLIP IP Address 192.168.10.2
VLAN VLAN 1
Spanning Tree Enabled (disabled in Version 1.0)
TFTP Mode Limited
TFTP Server 0.0.0.0
TFTP File Name p120.lst
Address Aging (CAM) Enabled
6. Install the Avaya P120
Standalone Manager
(optional)
The Avaya P120 Standalone Manager
allows you to configure and monitor the
Avaya P120 from your PC. The manager
is provided on a CD and comes with the
Avaya P120 switch.
System Requirements
Minimum hardware and Operating
System requirements are:
• Windows® 95 or NT® 4.0 or higher
• Pentium™ 200-Mhz-based, computer
with 64 Mb of RAM (Pentium-II rec-
ommended)
• Minimum screen resolution of
1024 x 768 pixels
• 24 Mb of free hard disk space.
Installation
To install the Avaya P120 Standalone
Manager:
1 We recommend that you close all
unnecessary applications currently
running on your PC
2 Insert the Avaya P120 Standalone
Manager CD in your PC’s CD Drive.
3 In Windows 95 or Windows NT, Click
“Start” on the taskbar and select “Run”.
4 Enter the path to the CD drive and
the filename setup.exe and click OK.
5 Follow the on-screen instructions to
install the Avaya P120 Manager.
Documentation and Online Help
The Standalone Manager CD comes with
a detailed User’s Guide including a
Glossary of Terms and an overview of
Data Communications concepts.
You can view the documentation without
installing the Standalone Manager.
avaya.com
All trademarks, registered trademarks, service names, product and/or brand names are the sole property of their respective owners.
Copyright © 2001, Avaya Inc. All rights reserved.
Catalog No. 223564 Rev. C
Autres manuels pour P120 SMON
2
Table des matières
Autres manuels Avaya Changer
Avaya
Avaya P333T-PWR Manuel utilisateur
Avaya
Avaya 8800 Series Manuel utilisateur
Avaya
Avaya ERS 4000 Series Manuel utilisateur
Avaya
Avaya 2500 Series Manuel du propriétaire
Avaya
Avaya Ethernet Routing Switch 8300 Series Manuel utilisateur
Avaya
Avaya 8800 Series Manuel utilisateur
Avaya
Avaya 4500 Series Manuel utilisateur
Avaya
Avaya 5900 Series Mode d’emploi
Avaya
Avaya 8800 Series Guide de démarrage rapide
Avaya
Avaya P332G-ML Manuel de l'opérateur
Avaya
Avaya P333T-PWR Manuel utilisateur
Avaya
Avaya 5900 Series Manuel utilisateur
Avaya
Avaya 8800 Series Manuel utilisateur
Avaya
Avaya 8800 Series Manuel utilisateur
Avaya
Avaya Ethernet Routing Switch 8300 Manuel utilisateur
Avaya
Avaya P334T-ML Manuel utilisateur
Avaya
Avaya 8600 Manuel utilisateur
Avaya
Avaya ERS 3500 Series Manuel utilisateur
Avaya
Avaya Ethernet Routing Switch 8300 Series Manuel utilisateur
Avaya
Avaya 5600 Series Manuel du propriétaire
