Avaya 3500 series Mode d’emploi
Installing Avaya Ethernet Routing Switch
3500 Series (NN47203-303 ver 01.01)
How to get help
To access the complete range of services and support that Avaya provides, go to
www.avaya.com.
You can also go to www.avaya.com/support to access the following pages:
• technical documentation
• product training
• technical support
If you purchased a service contract for your Avaya product from a distributor or authorized
reseller and you need assistance, contact the technical support staff for that distributor or
reseller.
Notices and alerts
Notice paragraphs alert you about issues that require your attention.
Following are descriptions of the types of notices used in this document.
Note:
Notes provide tips and useful information regarding the installation and operation of Avaya
products.
February 2013 1
Electrostatic alert:
ESD notices provide information about how to avoid discharge of static electricity and
subsequent damage to Avaya products.
Caution:
Caution notices provide information about how to avoid possible service disruption or
damage to Avaya products.
Warning:
Warning notices provide information about how to avoid personal injury when working with
Avaya products.
Voltage:
Danger—High Voltage notices provide information about how to avoid a situation or
condition that can cause serious personal injury or death from high voltage or electric
shock.
Danger:
Danger notices provide information about how to avoid a situation or condition that can
cause serious personal injury or death.
Safety messages
Safety messages are an important part of the technical documentation. The messages alert
you to hazards to personnel and equipment and provide guidance for the safe operation of
yourequipment.Failuretocomplywiththesafetymessagescouldresultinequipmentdamage
and personal injury.
Following are the most common types of safety messages.
Warning:
Installation must be performed by qualified personnel only. Read and follow all warning
notices and instructions marked on the product or included in the documentation.
Voltage:
This equipment relies on the building's installation for overcurrent protection. Ensure that a
fuse or circuit breaker no larger than 120 VAC, 15 A U.S. (240 VAC, 16 A International) is
used on the phase conductors.
Caution:
This device is a Class A product. In a domestic environment, this device can cause radio
interference, in which case the user may be required to take appropriate measures.
Safety messages
2 February 2013
Caution:
When mounting this device in a rack, do not stack units directly on top of one another in the
rack. Each unit must be secured to the rack with appropriate mounting brackets. Mounting
brackets are not designed to support multiple units.
Voltage:
Use only power cords that have a grounding path. Without a proper ground, a person who
touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to
the switch can result in excessive emissions.
Warning:
Disconnectingthepowercordis theonlyway toturnoffpowertothisdevice.Alwaysconnect
the power cord in a location that can be reached quickly and safely in case of an
emergency.
Warning:
Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look
into an optical fiber or connector port. Always assume that fiber optic cables are connected
to a light source.
Installation preparation
Related topics:
Before you begin on page 4
Installing the ERS 3510GT or ERS 3510GT-PWR+ switch on a table or shelf on page 4
Installing two ERS 3510GT or ERS 3510GT-PWR+ switches in an equipment rack on
page 6
Installing a single ERS 3510GT or ERS 3510GT-PWR+ switch in an equipment rack on
page 10
Installing the ERS 3524GT, ERS 3524GT-PWR+, ERS 3526T, or ERS 3526T-PWR+ switch
in an equipment rack on page 14
Connecting AC power on page 15
Installation preparation
February 2013 3
Before you begin
Ensure the area where you install and use the switch meets environmental requirements.
You can install a single ERS 3510GT or ERS 3510GT-PWR+ switch on any flat surface that
can safely support the weight of the switch and attached cables. An ERS 3510GT switch
weighs 3.85 lb (1.75 kg). An ERS 3510GT-PWR+ switch weighs 5.9 lb (2.70 kg). Cable weight
varies for each installation.
You can install two ERS 3510GT or ERS 3510GT-PWR+ units together to form one standard
width rack-wide system using a 19 inch side-by-side Rack Mount Kit (ordered separately).
You can install the ERS 3524GT, ERS 3524GT-PWR+, ERS 3526T, or ERS 3526T-PWR+
switches in an equipment rack using the brackets provided.
Environmental requirements
The following list describes the requirements for the switch environment.
• ambient temperature between 32°F and 122°F (0°C and 50°C)
• relative humidity between 0% and 95% noncondensing
• no nearby heat sources such as hot air vents or direct sunlight
• no nearby sources of severe electromagnetic noise
• no excessive dust
• adequate power source within six feet; one circuit required for each power supply
• at least 2 inches (5.1 cm) (or one vertical rack width) on all sides of the switch unit for
ventilation
• adequate space at the front and rear of the switch for access to cables
If you are installing a single Ethernet Routing Switch 3524GT, 3524GT-PWR+, 3526T, or
3526T-PWR+ on a table or shelf, ensure the surface can support at least 7 to 10 pounds (3 to
4.5 kilograms) .
Installing the ERS 3510GT or ERS 3510GT-PWR+ switch on a table
or shelf
About this task
You can install a single ERS 3510GT or ERS 3510GT-PWR+ switch on any flat surface that
can safely support the weight of the switch and attached cables. An ERS 3510GT switch
weighs 3.85 lb (1.75 kg). An ERS 3510GT-PWR+ switch weighs 5.9 lb (2.70 kg). Cable weight
varies for each installation.
Installation preparation
4 February 2013
Hardware included with ERS 3510GT and ERS 3510GT-PWR+ model switches:
•Avaya Ethernet Routing Switch 3500 Series
• Rubber footpads
• AC power cord (Note: a power cord is not included for the A variant of the switch)
• Base Software License Kit
• Screws (2) and wall anchors (2) for wall mounting
The following procedure provides instructions for installing the switch on a table or shelf.
Important:
Allow at least 2 inches (5.1 cm) on each side of the switch for proper ventilation and at least
5 inches (12.7 cm) at the back of the switch for power cord clearance.
Procedure
1. Attach the rubber feet at the marked locations.
2. Set the switch on a table or shelf.
Installation preparation
February 2013 5
Installing two ERS 3510GT or ERS 3510GT-PWR+ switches in an
equipment rack
Before you begin
Hardware included (in each box) with ERS 3510GT and ERS 3510GT-PWR+ model
switches :
• Avaya Ethernet Routing Switch 3500 Series
• Rubber footpads
• AC power cord (Note: a power cord is not included for the A variant of the switch)
• Base Software License Kit
• Screws (2) and wall anchors (2) for wall mounting
Tool requirements
• a Phillips screwdriver to attach brackets to the switch and the switch to the rack.
Bracket requirements
• one 3510–Pair Rack Mount Kit — this accessory kit is used to connect two ERS 3510GT
switches together side-by-side.. The kit includes all necessary brackets and fasteners and
must be ordered separately (Order Code AL3511002–E6).
The contents of the Side-by-Side Rack Mount Kit are as described below:
- 1. Rack mount brackets — Quantity: 2
- 2. M4 flat head screws — Quantity: 14
- 3. Hinged mating bracket — Quantity: 1
- 4. Rear bracket for mating identical 3510 switches — Quantity: 1
Installation preparation
6 February 2013
- 5. Rear bracket for mating 3510GT and 3510GT-PWR+ switches — Quantity: 1
-#10–32 rack mounting screws (not shown) — Quantity: 4
- #12–24 rack mounting screws (not shown) — Quantity: 4
- M6 rack mounting screws (not shown) — Quantity: 4
Rack requirements
• provide the equivalent of one rack of vertical space for each switch in an E1A or 1EC
standard 19 inch (48.2 cm) equipment rack and T1A 23 inch (58.5 cm) equipment rack.
• appropriate rack space to accommodate 1U switch height (44 mm).
• rack bolted to floor and braced if necessary
•rack must be grounded to the same grounding electrode used by the power service in the
area. The group path must be permanent and must not exceed 1 Ohm of resistance from
the rack to the grounding electrode.
Installation preparation
February 2013 7
Perform the following procedure to install your switch in an equipment rack.
Note:
Whenmountingtwo3510GT-PWR+unitssidebysideinanequipmentrack,runtheswitches
in high power mode to ensure adequate airflow. In high power mode, the available power is
170 Watts.
#show poe-main-status
PoE Main Status - Stand-alone
-------------------------------------------------
Power Mode : High Power Budget
Available DTE Power : 170 Watts
DTE Power Status : Normal
DTE Power Consumption : 0 Watts
DTE Power Usage Threshold : 80%
PD Detect Type : 802.3af and Legacy
Power Source Present : AC Only
AC Power Status : Present
DC Power Status : Not Present
Procedure
1. Ensure power is disconnected from the switch.
2. Connect the two ERS 3510GT switches together by opening the hinged bracket to
90° and attaching it to each ERS 3510GT switch with three M4 flat head screws
(included), as shown below.
Installation preparation
8 February 2013
3. Attach the standard rack mount bracket ears to the outer end of each switch as
shown below.
4. Once the switches are joined together, fold the hinged bracket inward.
5. Perform one of the following
•To connect two ERS 3510GT or two 3510GT-PWR+ switches together use
the rear bracket as shown below, with four M4 pan head screws to secure the
switches at the rear. Once the rear bracket has been installed, the switches
can be installed in the rack.
•To connect one ERS 3510GT switch and one ERS 3510GT-PWR+ switch
together use the offset rear bracket with four M4 pan head screws to join the
switches at the rear. Once the rear bracket has been installed, the switches
can be installed in the rack.
Note:
If you are mounting a mix of ERS 3510GT and ERS 3510GT-PWR+ units side
by side, ensure that the ERS 3510GT unit is mounted on the LEFT side (when
viewed from the front) for adequate airflow.
Installation preparation
February 2013 9
6. Slide the switches into the rack. Insert and tighten the rack mount screws.
7. Verify that the switch is securely fastened to the rack.
Installing a single ERS 3510GT or ERS 3510GT-PWR+ switch in an
equipment rack
Before you begin
Hardware included with ERS 3510GT and ERS 3510GT-PWR+ model switches:
• Avaya Ethernet Routing Switch 3500 Series
• Rubber footpads
• AC power cord (Note: a power cord is not included for the A variant of the switch)
• Base Software License Kit
• Screws (2) and wall anchors (2) for wall mounting
Tool requirements:
• a Phillips screwdriver to attach brackets to the switch and the switch to the rack
Bracket requirements:
•one3510–Single RackMountKit —thisaccessory kitisused tomounta singleERS3510GT
or ERS 3510GT-PWR+ switch in a standard 19 inch rack. The kit contains the necessary
Installation preparation
10 February 2013
Autres manuels pour 3500 series
7
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Avaya Changer
Avaya
Avaya Cajun P550 Manager 5.1 Manuel utilisateur
Avaya
Avaya P460 Manuel utilisateur
Avaya
Avaya 5900 Series Mode d’emploi
Avaya
Avaya Scopia XT Camera Switch Manuel utilisateur
Avaya
Avaya 8000 Series Mode d’emploi
Avaya
Avaya 2500 Series Manuel utilisateur
Avaya
Avaya P333R Manuel utilisateur
Avaya
Avaya P330 Manuel utilisateur
Avaya
Avaya 3500 series Manuel utilisateur
Avaya
Avaya 4500 Series Manuel utilisateur
Avaya
Avaya P130 SMON Manuel utilisateur
Avaya
Avaya Virtual Services Platform 7000 Series Mode d'emploi
Avaya
Avaya Virtual Services Platform 7200 Series Manuel utilisateur
Avaya
Avaya P114F Manuel utilisateur
Avaya
Avaya Ethernet Routing Switch 8300 Series Manuel utilisateur
Avaya
Avaya 8800 Series Manuel utilisateur
Avaya
Avaya Ethernet Routing Switch 8300 Series Manuel utilisateur
Avaya
Avaya Virtual Services Platform 7000 Series Manuel utilisateur
Avaya
Avaya VSP 7000 Series Mode d’emploi
Avaya
Avaya 5900 Series Manuel utilisateur
