Aurora Lite Bank Orion 200 Manuel utilisateur

Orion 200 / Orion 400

Contents

Modern compact and robust

Modern design constructed from durable red reinforced

polycarbonate to protect internal components and still remain

extremely light weight and portable.

Safety features

External shock protection with over-heat/over-charge functions.

Auto power dump

Automatically dumps high power when setting unit to lower power.

Dual power output display feature

Power output is displayed in f-stops and W/s.

Modular circuit board design

Plug in modular design with no soldering or internal wiring.

Accurate and easy power control

Accurate exposure over 5 f-stops.

1/10th f-stop power increments.

Full power to 1/32 by one long button push.

1/32 to full power by one long button push.

Modeling lamp

Full / Off / Proportional

Fast acting fuse for modeling lamp

Visual flash confirmation

Flash ready indicator beep when charged

Fan cooled for extra reliability and stability

5 Volt sync circuit

One touch lock button

Rapid recycle time

Short flash duration

Compatible with all Aurora accessories

Excellence In Lighting

1. Before use

2. Parts

3. Control panel functions

4. Operation

5. Specification

6. Trouble shooting

7. Warranty card

www.alb.co.kr e-mail : [email protected]

741-1 Sangyeok-dong, Buk-gu, Korea Tel : (82-53) 384-9874 Fax : (82-53) 384-9886

1. Before use

This flash unit is precision piece of equipment.

Please read the instructions thoroughly before use

Power

Protective cap should be removed before operation.

Insert power cord to socket on flash firmly, improper connection may cause fire.

Do not use damaged power cord or power socket. It may cause electric shock and fire.

Do not use the flash unit with other electrical appliances in the same socket, overheating may occur and cause fire and/

or electric shock.

Do not bend or pull or press power cord. It may cause electric shock and fire.

Use grounded power sockets only.

Settings

Mount the flash unit securely on a lighting stand or other secure mounting

Turn off power and pull out all plugs when carrying.

Do not use the flash unit in damp or wet conditions or where there is flammable material nearby.

Do not cover the flash with curtains or clothes.

Use only in a well ventilated space.

Storage

Keep the flash out of the reach of children.

Keep the ventilation holes of the unit clean at all time.

Keep the flash away from flammable or explosive materials.

Turn off the flash and unplug the power cord if it smokes or smells of burning or sounds unusual

Contact your local dealer or service center for repair.

If the unit is dropped and broken contact your local dealer or service center.

Keep pins in the power plug and their contact parts clean at all time.

Clean with a soft dry cloth only.

Do not use with incorrect accessories. It is recommended you use or genuine Aurora accessories.

Modeling Lamp

To avoid burns do not touch modeling lamp when it is on.

To avoid eye damage do not look at modeling lamp when it is illuminated.

Do not expose modeling lamp to rain or moisture.

Turn the flash off and unplug the power cord when replacing modeling lamp. Do not touch modeling lamp with

bare hands, use cotton gloves or a soft cloth

ly, improper connection may cau

2. Parts

3. Control panel functions

① Handle

② Locking lever

③ Mounting plate

④ Flashtube

⑤ Modeling

⑥ Modeling lamp socket

⑦ Umbrella fixing

⑧ Tightening screw

⑨ Tilt mounting bracket

①Photo cell:

Light sensor

②

Up/Down

Flash output increases and decreases by

1/10 f-stop – full power to 1/32 or 1/32 to full power.

③Test:

Flash trigger

Green LED indicates ready to trigger and no LED

indicates still charging.

④Power on/off switch

⑤

Power inlet

⑥Main fuse

⑦Modeling lamp fuse

⑧Sync socket

⑨Model:

3 modes for modeling lamp control

- Press Model button once (red LED/Full mode): modeling lamp sets to maximum output.

- Press Model button twice (green LED/Proportional mode): modeling lamp is proportional to flash output

- Press Model button three times (no LED/Off mode): modeling lamp is controlled by slider on back panel.

⑩

Alarm:

Audible alarm indicates charge status.

Alarm on: Alarm beeps while charging and stops when fully charged

Alarm off: Modeling lamp flickers when fully charged.

⑪

Slave

Slave on: Flash unit syncs. by light sensor as well as sync. cord.

Slave off: Flash unit syncs. by cord only.

⑫Power Display:

Output display in Ws or f-stop To change power display from f-stop to Ws or vice versa, press up

and down buttons at the same time for more than 10 seconds. If the unit overheats, power display winder will flicker

and the alarm will beep. The modeling lamp will go off and unit will stop functioning except for the cooling fan. When

cooled, the unit will restart automatically.

5. Specification

ORION 200 ORION 400

Max Power 200 Ws 400 Ws

Power Increment 1/10 f-stop 1/10 f-stop

L x W x H 24 x 13.5 x 17 cm 24 x 13.5 x 17 cm

Weight 1.4 kg 1.65 kg

Power Display Ws or f-stop Ws or f-stop

Power Range

FULL~1/32 FULL~1/32

5 f-stops (3Ws to 200Ws) 5 f-stops (12Ws to 400Ws)

Duration(T=0.5)

Recycle Time 0.2 ~ 1.4 sec

1/2950 sec

0.2 ~ 1.6 sec

Colour Temperature 5500+/-250k 5500+/-250k

Modeling Lamp 100W, 150W

Operating Voltage AC 230V 50Hz/60Hz or 120V 50Hz/60Hz

Auto Dump Yes

Ready Sound Yes (On/O)

Standard Reector Included Yes

Fan Cooled Yes

Slave Cell Yes ( On / O )

Modeling Control Full / Proportional / O

Flash Test Button Yes

Sync Voltage 5V DC

Power Cord Included 5m long

Sync Cord Included 3.5mm ( Mono - Pc ) / 5m long

1/2000 sec

MODEL

SUBJECT

4. Operation

8)To use an umbrella, mount a standard reflector and insert the umbrella shaft

through reflector hole and into the two holes in the tilt mount. After use, cool

down the flash unit and umbrella. Do not pull out the umbrella before cooling.

9)To use a softbox, assemble the softbox prior to placing it onto the flash.

Fit the claws of the adaptor into the holes in the flash front panel and then rotate the softbox

clockwise until it clicks into place. To detach the softbox, make sure the unit is cool enough to touch;

press the locking button with one hand and rotate the softbox anti clockwise with the other hand to remove it

1)Make sure modeling lamp switch and power switch are off.

2)Connect sync cord and power cord to appropriate sockets.

3)Turn on the power switch.

OFF

4)Press test button to ensure the unit is functioning correctly

5)All switches are one-touch. ALARM, SLAVE and MODEL are off by default.

(Turn them on as per your requirements).

6)“MODEL” button offers 3 different modes:

- Press Model button once (red LED / Full mode): modeling lamp sets to maximum output.

- Press Model button twice (green LED / Proportional mode): modeling lamp is proportional to flash output

- Press Model button three times (no LED / Off mode): modeling lamp is controlled

by slider on back panel.

7)To Increase or decrease flash power, press up and down buttons.

When power output is decreased, the flash will trigger automatically and dump excess power.

For warranty, please fill out this form and mail to Aurora Lite Bank Co.,

741-1 Sangyeok-dong, Buk-gu, Dae-gu, 702-101, Korea or fax to +82-53-384-9886.

Aurora Lite Bank warrants this product to be free of defects in materials and workmanship

for a period of 12 months from the date of purchase.

We or our authorized service centre will repair or replace this product without charge with

respect to the parts and labor, providing our examination indicates that functional defect

exists under normal usage.

This warranty, however, does not include damage caused by the following reasons and

repair or replace for defects due to the followings will be charged.

- Abuse and improper handling

- Improper maintenance

- Unauthorized repairs or modifications

- Natural disaster such as flood, moisture or animal damage

- Defective connection tools

- When wasting parts; modeling lamp, soft box, flash tube, synchro cord,

connecting cable, photo condenser need to be replaced

This warranty is valid only for the original owner and applies to customers who properly fill

out and return this warranty card.

Where did you purchase this product?

Name

Street Address

City

State/Province Zip Code

Country

Phone Number Fax Number

E-mail Address

Purchase Date

※ This product can be modified For better quality and function without prior notice.

Warranty Card

6. Trouble shooting

Does not operate No power to unit

Check if power cord is connected to AC inlet and outlet properly.

Flash res on its’ own.

Sync via photo cell

from another ash.

Turn o the slave and check if it still res

Modeling lamp does

not light.

Switched o Check if modeling lamp switch is o.

Will not re when

power is on.

Defective sync socket

or sync cord

Try to trigger with test button. Check sync socket and cord.

Continuous beeping

Problem with charging

Check input voltage is not lower than required

Others Consult with authorized service center, dealers or the manufacturer

Overheating Check if cooling fan operates normally.

If it does, cool the ash before trying to re-use.

Defective RF trigger

or no batteries in RF

receiver or transmitter

Try to trigger with test button. Check RF transmitter and receiver

operation.

Defective ashtube Try to trigger with test button. Replace ash tube with new one.

Lamp blown Replace with a new modeling lamp.

Fuse blown. Replace blown fuse with a new fuse of the same rating.

Defective sync cable

or RF receiver

Disconnect sync cable and check if it still res.

Defective test buttonr

Check if test button works properly.

Colour cast in images

Cover up surrounding wall and oor with black fabric or paper.

No sync through

photo cell

Slave is o Turn slave on.

Ambient light is too

bright and ‘blinding’

slave cell

Isolate the ash from other light sources such as the sun.

Cover up the part of photo cell which is being exposed to too

bright ambient light.

Light from another

ash does not reach

to the photo cell

Move the ash unit so that light from the other unit reaches the

slave cell.

Check if power switch is on

Check if main fuse is blown.

Check if there is power to the A/C socket and that the switch is on.

Symptom Possible Cause Solution

Flash unit is reecting

o coloured walls of

wallpaper

Ce manuel convient aux modèles suivants

Autres manuels Aurora Lite Bank Flash de l'appareil photo

Aurora Lite Bank

Aurora Lite Bank FORESTO-100 Manuel utilisateur

Manuels Flash de l'appareil photo populaires d'autres marques

Canon

Canon 5246B002 Manuel utilisateur

Sigma

Sigma EF-610 DG SUPER - Manuel utilisateur

Godox

Godox DP300 Manuel utilisateur

Sony

Sony HVL-FDH4 Manuel utilisateur

Sony

Sony HVL-RLA Manuel utilisateur

Nikon

Nikon SB-28 Manuel utilisateur

Canon

Canon Speedlite 380EX Manuel utilisateur

Olympus

Olympus FL 36R Manuel utilisateur

Nikon

Nikon BC-7 Manuel utilisateur

Altura Photo

Altura Photo AP-305N Manuel utilisateur

Nikon

Nikon SB-800 Manuel utilisateur

DÖRR

DÖRR DFX-300 Manuel utilisateur

Canon

Canon SPEEDLITE 300EZ Manuel utilisateur

Sunpak

Sunpak 622 Super Pro-System Manuel utilisateur

Polaroid

Polaroid PL108-AF Manuel utilisateur

Godox

Godox Thinklite TT350P Manuel utilisateur

Pentax

Pentax AF240Z Manuel utilisateur

Pixapro

Pixapro Li-ion 350 II N Manuel utilisateur