Auper Eclipse 784 B Manuel d'instructions

Auper Electronic Controls Inc

Eclipse 784 B

Quick User Guide

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

INSTALLATION

1. Mount your Eclipse system, away from areas where liquor spills could fall onto the

Eclipse. The system is protected with silicone but it is not guaranteed to be liquid

proof. Liquid spills can find their way to the connectors causing corrosion and eventually

penetrate the enclosure.

2. Mount the activator ring holder to the right of the system (Most people are right handed) where

it is most convenient for bartenders. Soft drink guns should be mounted on the left of the

system.

3. Secure the activator ring and extension to the activator ring port on the system.

4. If you connect the Eclipse system to a serial port (printer, PC or POS), install the communication

cable and test it before securing the system under the bar.

5. Secure your activator ring cable to the ring holder using a cable tie.

6. Connect the power supply cord to the 20 VA, 12 volts AC transformer. We recommend using a

battery backup with surge protector if you are in an area where power failures are frequent.

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

SERIAL CONNECTION

CONNECTING THE ECLIPSE TO A SERIAL PRINTER

To connect a serial printer to the Eclipse , use the RS-232 port. With new

printers, the 9-pin female serial cable supplied with the printer is directly

compatible.

Set the RS-232 port to printer. (See programming)

Printer settings

Baud rate: 9600

Parity: none

Stop bit: 1

Handshaking: Xon/Xoff

Print columns: 40

CONNECTING THE ECLIPSE TO A COMPUTER

You can connect your Eclipse to your PC to use the Liquor Manager software

(cable and software purchased separately). Use a RS-232 null modem cable

(P/N: 70-030).

RS-232 Null modem pin-out:

Null modem with loop back handshaking

The RS-232 cable cannot exceed 100 ft (30 meters).

Set the RS-232 port to PC. (See programming)

RS-232 null modem cable

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

CONNECTING THE ECLIPSE TO A POS OR CASH REGISTER

Interfacing an Eclipse to a POS is achieved using the RS-232 serial port. You can connect

your Eclipse to your POS or cash register using a RS-232 null modem cable (P/N: 70-

030). Samsung registers require a gender changer connector.

Set the RS-232 port to POS. (See programming)

USB TO SERIAL CONVERTER

Newer computers may not be equipped with 9-pin serial ports. A USB to serial adapter will

solve the problem. Drivers are provided with the converter and must be installed on the

computer. Windows will assign the serial port automatically. You can find to which port

your converter has been assigned at:

Control panel/system/device manager/ports (Com & LPT)

The defaults Windows serial port settings are:

9600 bps, 8 bits, no parity, 2 stop bits and no flux control.

RS-422 SERIAL PORT CONNECTIONS

You will use the RS-422 port for the following reasons:

You wish to connect your Eclipse system to a computer more than 100 ft (30M) away.

You have more than one Eclipse that you want to connect to the same computer, POS or printer.

Use straight RS422 twisted pair cables between the Eclipse and the AP421 converter (P/N: 70-042-X).

RS-422 TO RS-232 CONVERSION

When using the RS-422 port, you will need to convert the signal back to RS-232 before you can connect

your cable to a computer, POS or printer. The AP421 converter will

accommodate up to four RS-422 inputs to convert to a single RS-232 port.

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

CODED POURERS

Use the magnetic pourer tool to open the pourer when pushing the normally closed

pourer into a new bottle. That will prevent pressurizing the liquid inside the bottle

forcing it up the breather tube and air vent.

INSERTS

If the insert provided with the pourer is too loose, liquor will leak between the pourer

and bottleneck. Select the bigger size and change the insert. If the insert is too tight,

the pourer will be hard to remove from the bottle. This often leads to the breather

tube being pulled out when you try to remove it from the bottle. Trim the top wing

using a nail clipper or a cutter.

Clean your pourers

immediately after taking

them off the empties.

Do not use soap and do not

clean in a dish washer.

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

SEALS

1. Two-part seal

Remove a plastic seal from the roll and apply on top of the pourer. Pull both tabs onto the neck. Wrap a

seal label around the neck of the bottle and the plastic tabs.

2. Shrink seal

Slide the heat shrinkable seal over the pourer, hold in place and apply heat

evenly to shrink the seal to the bottle using a heat gun.

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

PROGRAMMING

To access the program modes, Press and hold the Sbutton as you apply the manager’s i-button

onto the probe (1 of 6 i-buttons).

To get out of the programming mode, apply the i-button again.

To change mode, press M once. You cannot go back. To come back, press M until you have

passed all the program modes.

MODE 1: POUR SIZE TIMER

A TIMER setting of 33 equals approximately 1oz (30ml) Products with a

higher viscosity will take more time to serve.

To view a different code and size press the S button to move up and

the R button to move down.

Pour a drink into a graduated cylinder.

Measure the volume of the drink poured.

Press the L button to increase the timer value.

Press the SP button to decrease the timer value.

Press M to skip.

MODE 2: COPY TIMER SETTINGS

Press SP to copy the timer values you have just set to all the pourer

codes.

Press M to skip.

MODE 3: POS AND REGISTER INTERFACE

If you do not interface your Eclipse to a POS or a cash register, make sure the

system is set to POS DISABLED. The next modes only apply when the

interface feature is set to enable. Go directly to the serial port setting

section.

Press SP to set the POS interface to Enabled/Disabled.

Press M to skip.

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

When set to POS Enabled (7), the Eclipse

784 will send the PLU programmed in its

PLU table corresponding to the pourer

number and pour size selected through

the selected serial port. The PLU is sent as

if the item was scanned by an IR scanner.

The data is sent in the following format:

Example: PLU 0201 is sent as: 30 32 30

31 0D 0A

OD= Carriage return bytes 0A: New line

bytes

As opposed to the other interface

protocols, no reply from the ECR or POS is

expected by the Eclipse to serve the

drink.

Protocols available:

The following modes are available if POS Interface is set

to Enabled.

Press the L button to change the interface protocol.

(1) Berg

(2) Micros NA

(3) Auper

(4) Addimat

(5) Veloce brand ID

(6) CSI

(7) IR Scanner

(8) Debit/Credit interface

PLU table

The default factory PLU table can be changed using the Liquor Manager software.

Code

PLU S

PLU R

PLU L

PLU SP

0101

0111

0121

0131

0102

0112

0122

0132

0103

0113

0123

0133

0104

0114

0124

0134

0105

0115

0125

0135

0106

0116

0126

0136

0107

0117

027

0137

Eclipse 784B Quick User guide

2010 Auper Electronic Controls Inc Edition E784BE 1.2

MODE 4: ACK TIME OUT (INTERFACE SET TO ENABLED ONLY)

Sets the time your liquor system will wait for a reply from your POS system

after a pour request has been sent. This timer is necessary to prevent the

liquor system from waiting indefinitely in case the POS reply did not come.

Press the S button to decrease this value.

Press the R button to increase this value.

Press M to skip.

MODE 5: PLUS FORMAT (INTERFACE SET TO ENABLED ONLY)

You can select the format of the PLUs sent by the Eclipse to the POS. For

example: PLU 0651

If the 4-digit PLUs is set to Y: the PLU will be sent as is 0651.

If the 4-digit PLUs is set to N: the PLU will be sent as 651 only.

Press SP to select between Yes or NO.

Press M to skip.

MODE 6: PC COM PORT SELECTION

Press SP to alternate between RS-232 and RS-422.

If you are connecting the Eclipse to a PC using the RS-232 serial

port, set to RS-232.

If you are connecting one or more Eclipse systems using the RS-422 port, set to RS-422.

If you are not using a PC, Press M to skip.

MODE 7: POS COM PORT SELECTION

Press SP to alternate between RS-232 and RS-422.

If you are interfacing the Eclipse to a POS terminal or cash

If you are interfacing one or more Eclipse systems using the RS-422 port, set to RS-422.

If you are not interfacing your system to a POS, Press M to skip.

MODE 8: PRINTER COM PORT SELECTION

Table des matières

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur