AUO JECTOR Manuel utilisateur
Lecturer Tracking Camera
User Manual V1.3
JECTOR Digital Corporation
5F.-2, No.268, Liancheng Rd., Zhonghe Dist.,
New Taipei City 235038, Taiwan(R.O.C.)
TEL / +886 2 82273311
E-mail / [email protected]
www.jectordigital.com
SAFETY NOTES
The following important notes must be followed carefully to run the camera and respective
accessories in total safety. The camera and relative accessories are called video system in this
section.
Before installing the camera, please read this manual carefully. Please follow installation
instructions indicated in this manual during installation. Please keep this manual for future
use.
The installation should be performed by qualified service personnel or system installers in
accordance with all local rules.
Before powering on the camera, please check the power voltage carefully. Make sure that
you are using the correct power source.
Please put the power cable, video cable and control cable in safe place.
Do not operate the camera beyond the specified temperature and humidity. Working
temperature range of the camera is between 0℃~ +40℃. The ambient humidity range is
10%RH ~ 90%RH.
During transporting, avoid violent shake or force to the camera.
To prevent electric shock, do not remove screws or housing of the camera. There are no
self-serviceable parts inside. Refer to qualified service personnel for servicing.
Never aim the lens of the camera at the sun or other extremely bright objects. Otherwise, it
may cause damage.
When cleaning the camera, please use soft cloth. If the camera is very dirty, wipe it off gently
with a soft cloth moistened with a weak solution of water and a neutral kitchen detergent.
Wring all liquid from the cloth before wiping the camera, then wipe off all remaining dirt with a
soft, dry cloth. Use lens cleaning paper to clean the lens.
Do not move the camera head manually. In doing so would result in malfunction of the
camera. Do not hold the camera head when carrying the video camera.
This camera is for indoor use only. It is not designed for outdoor use.
Make sure the camera is not directly exposed to rain and water.
Make sure the camera is far away from area where radiation, X-rays, strong electric waves, or
magnetism is generated.
CONTENTS
ABOUT THE PRODUCT-------------------------------------------------------- 1
QUICK GUIDE ----------------------------------------------------------------------------- 1
ABOUT THE PRODUCT-------------------------------------------------------- 2
FEATURES -------------------------------------------------------------------------------- 2
LIST OF PARTS &ACCESSORIES ----------------------------------------------------------- 2
MAIN PARTS &INTERFACES---------------------------------------------------------------- 3
DIP SWITCHES SETTINGS------------------------------------------------------------------ 4
REMOTE CONTROLLER -------------------------------------------------------------------- 5
INSTALLATION ---------------------------------------------------------------- 7
DESKTOP MOUNT INSTALLATION ----------------------------------------------------------- 7
WALL MOUNT INSTALLATION (OPTIONAL)--------------------------------------------------- 7
CONNECTIONS ---------------------------------------------------------------- 8
MENU SETTINGS -------------------------------------------------------------- 9
MENU CONFIGURATION -------------------------------------------------------------------- 9
MENU EXPLANATION---------------------------------------------------------------------- 13
VIDEO ----------------------------------------------------------------------------------- 14
EXPOSURE------------------------------------------------------------------------------- 14
COLOR---------------------------------------------------------------------------------- 15
PAN/TILT/ZOOM-------------------------------------------------------------------------- 16
SYSTEM --------------------------------------------------------------------------------- 16
STATUS -------------------------------------------------------------------------------- 17
RESTORE DEFAULTS --------------------------------------------------------------------- 17
LIST OF SPECIAL PRESET COMMANDS----------------------------------------------------- 17
NETWORK CONNECTION --------------------------------------------------- 18
LAN CONNECTION ----------------------------------------------------------------------- 18
WAN CONNECTION----------------------------------------------------------------------- 18
CLIENT SOFTWARE INSTRUCTION----------------------------------------- 20
SEARCH AND LIST THE CAMERA ---------------------------------------------------------- 20
SETTING --------------------------------------------------------------------- 25
SOFTWARE CONNECTION ----------------------------------------------------------------- 25
ANNEX 1 TECHNICAL SPECIFICATIONS------------------------------------ 27
ANNEX 2 SIZE AND DIMENSION -------------------------------------------- 29
TROUBLESHOOTING-------------------------------------------------------- 31
1
ABOUT THE PRODUCT
Quick Guide
The camera can be accessed and controlled
via the following ways:
Client software CameraCMS: camera
search and control, network setting;
VLC: watch the camera two streams;
IE: camera image preview, camera control,
network setting;
Onvif: version 2.1 supported
Name: admin
Initial password: 123456
Network pass-through: recommended
connection mode with recording or
streaming device.
CameraCMS
Refer to detailed instructions in page 20 of this
user manual.
Rtsp
1 Make sure PC and the camera are in the
same LAN.
2 Two channel streams, url: rtsp://IP/chx, x=1,
2.
3 IP address is acquirable through
CameraCMS, default rtsp port is 554.
IE
1 Make sure PC and the camera are in the
same LAN;
2 Input IP address+ port number 88 (port
numbers fixed to 88) in the IE address bar:
http://IP:88, such as
http://192.168.18.229:88
3 Install plug-in;
4 Name: admin Initial password: Null;
5 Support Windows 7 or above operation
system, whereas Windows XP is not
supported.
Network Pass-Through
On the tracking parameters setting page, the
IP address, port and connection protocol
(TCP/UDP) of the recording or streaming
device can be configured. After connected,
the camera can be controlled by the standard
VISCA protocol. Recording or streaming
device can achieve audio & video of the
camera through rtsp or rtmp.
2
ABOUT THE PRODUCT
Features
Built-in industry-leading body detection and
lock tracking image algorithm;
1/2.8 inch CMOS sensor, 2.14 megapixel;
20x optical zoom, Max FOV: 59.5°;
Support HDMI, 3G-SDI, Network, USB, up
to 1080P60 video output;
1 channel audio LINE IN, AAC
Compression;
Support two modes of power supply, POE
(optional) power supply or adapter power
supply;
Support VISCA interface and protocol,
support flow control;
Dual stream.
List Of Parts & Accessories
When you open the box, check all accessories
according to the packing list.
Camera (1)
Power Adapter (1)
Remote Controller (1)
RS-232 Control Cable (1)
3
Main Parts & Interfaces
Camera
Front View
1 Camera Module
2 Communication Indicator
3 Power Indicator
Rear View
4 USB
5 HDMI Video Output
6 LINE IN
7 Network
8 SDI
9 RS-232IN/IR
10 RS-232OUT/RS-485
11 DC12V
RS-232IN/IR Pin Definition
Number Definition
1 /
2 /
3 232-TX
4 GND
5 232-RX
6 GND
7 IR
8 /
RS-232OUT/RS-485 Pin Definition
Number Definition
1 /
2 /
3 232-TX
4 GND
5 232-RX
6 GND
7 485+
8 485-
4
Bottom View
12 DIP Switch
Set camera video format and menu.
13 Mounting Hole
1/4” inch screw thread for fixing camera.
14 Locating Hole
To define installation direction of camera.
DIP Switches Settings
Before installing and operating the camera,
set video output format and menu through DIP
switches. The camera has two 4-digit DIP
switches. SW as below:
SW Settings
No 1~4 is used to set video output format and
menu. Refer to below chart for details:
Please change video formats through special
presets.
Note
PTZ reboot is necessary for the new setting
to take effect.
5
Remote Controller
1 HOME
Press HOME button, camera moves to
initial position.
2 Camera Selection Button
Used to switch among 4 cameras, press 1-4
number buttons to control cameras with 1-4
addresses respectively. For example, press
button 1 to control the camera with address
1.
3 Focus
Press “AUTO” button to switch to Auto
Focus, press “MANU” button to switch to
Manual Focus mode.
“”button to Focus Near
“”button to Focus Far
“”button to Auto Focus once every time
it is pressed, then switch back to Manual
Focus mode.
4 Iris
Press“ ”button to reset iris (image
brightness) value to default. “ ”button to
Iris Open (brighter image)
“”button to Iris Close (darker image).
5 Menu
Press MENU button to enter / exit menu.
6 Data
Reserved.
7 Number Keys
Table des matières
