Audiovox Prestige APS-25KB Manuel utilisateur

Model APS-25KB

Installation Manual

PRE-INSTALLATION NOTES:

AUTO LOCK / UNLOCK : DIP SWITCH #1

The system is shipped with this feature activated.

Anytimetheignitionkeyisturnedtotheoffposition,thedoorswillautomaticallyunlock. Anytimetheignition

key is turned to the on position, the doors will automatically lock.

To disable the auto lock/unlock feature, move dip switch number 1 to the "off" position.

PASSIVE/ACTIVEDOORLOCK SELECTION: DIP SWITCH #2

This feature will only affect the operation of the system if the passive arming feature is selected.

When active door lock is selected, the doors will only lock when the transmitter button is pressed. When the

alarm is allowed to arm passively, at the end of the 30 second arming cycle, the doors will not automatically

lock.Thesystemisshippedintheactivedoorlockmode,therefore,nomodificationsarerequiredforthisfeature.

When passive door lock is selected, when the alarm is allowed to arm passively, at the end of the 30 second

arming cycle, the doors will automatically lock. To program this feature, move dip switch number 2 to the on

position.

PASSIVE/ ACTIVE ARMING SELECTION: DIP SWITCH#3

This alarm can be programmed to operate as either a “PASSIVE” or “ACTIVE” arming security system.

Asa“Passive” alarm,the system willautomatically armitself approximately 30seconds after theignition key

isturnedoff,onedoorisopened,thenallvehicledoorsareclosed, (armingissuspendeduntilthelastdooris

closed).Thisfeatureprotectsthevehicleintheeventyouforgettoarmthesystemusingthekeychaintransmitter.

Whentheoptionaldoorlockinterfaceisinstalled,thedoorswilloperateaccordingtothepositionofdipswitch

number2.

Thissystemisshippedinthepassivemode,thereforenomodificationsarerequiredtomakethesystemoperate

asa“Passive”alarm.

As an “Active” alarm, the system can only be armed using the keychain transmitter. There will be no backup

automaticarming.

To make the system operate as an “Active” alarm, move dip switch number 3 to the off position.

VOLTAGESENSE/HARDWIRESELECTION:DIPSWITCH#4

This alarm can be wired to operate as a Voltage Sensing or a Hardwire system.

As a voltage sensing system, the alarm will trigger any time an entry point that illuminates a courtesy light is

opened.Thesystemisshippedinthevoltagesensingmode,therefore,nomodificationsarerequiredtomake

this system a voltage sensing alarm.

As a hardwire system, the alarm will trigger any time a door, hood, trunk, etc. is opened, by wiring directly to

the switches. This means that if the courtesy light is burned out, or the courtesy light fuse is blown, the alarm

will continue to protect all points of entry. To make this system operate as a hardwire alarm, move dip switch

number 4 to the off position.

NOTE: When“PassiveArming”and“VoltageSensing”areselected,youmusthardwirethedriver’sdoorpin

switchorpassivearmingwillneverbeinitiated.

Page 2

CHANNEL2OUTPUT:

Thissystem provides anadditional hardwireremote outputto controlan assortment ofoptional upgrades.

Thisoutputisan independentchannelfromthe transmitter, andiscontrolled by button#2on the transmitter.

It is a delayed ground pulse (300 mA maximum), and can be used to control:

•Optional trunk release relay AS-9256

•OptionalremotestarterAS-9075

•OptionalwindowrollupAS-9153

CHANNEL3OUTPUT(TransmitterOnly):

Thetransmittersincludedinthisalarmincorporateanadditionalindependent3rdradiochannel. Althoughthe

alarmmodulewillonlyrespondto2channels,the3rdradiochannelcanbeprogrammedtoanoptionalgarage

doorinterface(AS-9154).

The AS-9154 has its own on-board programmable receiver and is designed to operate with most existing

automaticgaragedooropeners.

Inaddition,thegaragedoorinterfacereceivercanbedirectlywiredintothevehicletoofferathirdremotecontrol

option. Sincethisisasetofrelaycontacts,thereceivercanbeusedtoprovideaselectablepositiveornegative

pulse.

TRANSMITTERPROGRAMMING:

ThetransmittersincludedinthiskithavebeenprogrammedatthefactoryfortheChannel1(arm,disarmand

panic function) only. Any additional functions of the system (Channels 2 and 3) must be programmed at the

timeofinstallation. Thesefunctionscanbeassignedtotransmitterbuttonnumber2orasimultaneouspress

of both buttons 1 and 2.

Refer to the transmitter programming guide, included in this package, for more details regarding transmitter

button assignments and system functions.

INSTALLATIONOFMAJORCOMPONENTS:

CONTROLMODULE:

Selectamountinglocationinsidethepassengercompartment(upbehindthedash) andsecureusingtwoscrews

provided.

The control module can also be secured in place using cable ties.

Do not mount the control module in the engine compartment, as it is not waterproof. You should also avoid

mounting the unit directly onto factory installed electronic components. These components may cause RF

interference,which canresultinpoortransmitterrangeorintermittentoperation.

SIREN:

Selectamountinglocationintheenginecompartmentthatiswellprotectedfromaccessbelowthevehicle.Avoid

areasnearhighheatcomponentsormovingpartswithintheenginecompartment.Topreventwaterretention,

theflared,oropenedend,ofthesirenmustbepointeddownwardwhenmounted. Mount thesirentotheselected

location using the screws and bracket provided.

HOOD OR TRUNK PIN SWITCH:

A pin switch is included for use in protecting the hood or trunk (or hatchback) of the vehicle.

Theswitchmustalwaysbemountedtoagrounded,metalsurfaceofthevehicle.Itisimportanttoselectalocation

wherewatercannotfloworcollect andtoavoidalldrip“gutters”onhoodandtrunkfenderwalls.Chooselocations

that are protected by rubber gaskets when the hood or trunk lid is closed.

The pin switch can be mounted using the bracket provided or direct mounted by drilling a 9/32" diameter

mountinghole.

Keepinmindthatwhenproperlymounted,theplungerofthepinswitchshoulddepressatleast1/4"whenthe

hood or trunk lid is closed.

Page 3

DASH MOUNTED LED:

AsmallredLED is includedthatwillserve as avisualindicator of thealarmstatus.It should beinstalledinthe

dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver.

Oncealocation has beenselected,check behindthepanel for wirerouting access andtoconfirm thedrillwill

not damage any existing components as it passes through the panel.

Drilla1/4"diameterhole,andpasstheredandbluewiresfromtheLEDthroughthehole,fromthefrontofthe

panel. Firmly press the body of the LED into the hole until fully seated.

SHOCK SENSOR:

Select a solid mounting surface for the shock sensor on the firewall inside the passenger compartment, and

mount the sensor using the two screws provided. The shock sensor can also be secured to any fixed brace

behind the dash using tie straps.

Whichever mounting method is selected, make certain that the sensitivity adjustment is accessible for use

later in the installation.

VALETSWITCH:

Select a desired mounting location for the switch, that is easily accessible to the driver of the vehicle.

The switch does not have to be concealed, however, concealing the switch is always recommended, as this

providesanevenhigherlevelofsecuritytothevehicle.Theswitchmaybemountedinorbelowthedashbydrilling

a1/4" diameter hole in thelocation. Be sure to check behindthe dash for adequate clearancefor the body of

theswitch,andtoconfirmthatthedrillwillnotdamageanyexistingcomponentsasitpassesthroughthedash.

Whichever mounting method is used, make certain the back of the switch is accessible for wiring later in the

installation.

WIRING THE SYSTEM:

WHITE WIRE: + 12 VDC PULSED PARKING LIGHT OUTPUT ( 15 A MAX )

Thiswire isprovided to flash the vehicle’sparking lights. Connectthe white wire to thepositive sideof one of

thevehicle’sparkinglights.

RED FUSED WIRE - (VOLTAGE SENSING): + 12 VDC CONSTANT BATTERY SOURCE

This wire controls the sensitivity of the voltage sensing circuit, which detects the turning on of an interior light

whenadoorisopened.Itwillalsodetecttheswitchingonofparkingorheadlamps,andinmanycaseswilltrigger

thealarmwhenathermostaticallycontrolledelectronicradiatorcoolingfanswitcheson. Itisrecommendedthat

when installing this system into vehicles with electronic “after fans”, the procedure for RED FUSED WIRE -

(HARDWIRE) shouldbefollowed.

In voltage sensing applications, the closer to the battery that the red wire is connected, the less sensitive the

voltage sense circuitry will be. Moving this connection point to the fuse panel will increase the sensitivity and

connectingtothecourtesylampfuseinthevehiclewillprovidemaximumsensitivityofthevoltagesensecircuit.

RED FUSED WIRE - (HARDWIRE): + 12 VDC CONSTANT BATTERY SOURCE

Whenhardwiringthecontrolmoduletopinswitchesatallentrypoints,thevoltagesensecircuitmustbedisabled.

Move dip switch # 4 to the "OFF" position. Connect the red wire to a + 12 VDC constant battery source.

DARKBLUEWIRE:300mAPULSEDOUTPUT/CHANNEL2

The dark blue wire pulses to ground via an independent RF channel from the keychain transmitter. This is a

transistorized, low current output, and should only be used to drive an external relay coil.

WARNING:Connectingthedarkbluewiretothehighcurrentswitchedoutputoftrunkreleasecircuits

or some remote starter trigger inputs, will damage the control module.

Connectthedarkbluewiretoterminal86oftheAS-9256relay(orequivalent30Aautomotiverelay),andwire

the remaining relay contacts to perform the selected function of channel 2.

WHITE w/ BLACK TRACE WIRE: POSITIVEOUTPUT TOSIREN

Routethiswirethrougharubbergrommetinthefirewalltothesirenlocation. Connectthewhite/blackwireto

the positive wire of the siren. Secure the black ground wire of the siren to chassis ground.

BLACKWIRE:CHASSISGROUND

Connect this wire to a solid, metal part of the vehicle’s chassis. Do not confuse this wire with the thin black

antennawirethatexitsthecontrolmoduleindependently.

YELLOW WIRE: + 12 VDC IGNITION SOURCE

Connect this wire to a source that supplies 12 VDC when the ignition key is in the ON and CRANK positions

and off when the key is in the OFF position.

DARK GREEN WIRE: (-)INSTANTTRIGGER

This is an instant on ground trigger wire. It must be connected to the previously installed hood and trunk pin

switches.

BROWNWIRE:-DOORTRIGGER

Ifthe vehicle’sdoor courtesylight switcheshave a - ground output when the door isopened (GM andmost

Imports)youmustconnectthiswiretothenegativeoutput from one of the doorswitches.Inmostcases,the

brown wire will only need to be connected to one door switch, no matter how many doors the vehicle has.

WARNING: Do not use the brown wire if the vehicle has + 12 Volt output type door switches. (see

PURPLEWIRE)

PURPLEWIRE:+DOORTRIGGER

Ifthevehicle’sdoorcourtesylightswitcheshavea+12voltoutputwhenthedoorisopened(mostFordsand

someImports),youmustconnectthiswiretothepositiveoutputfromoneofthedoorswitches.Inmostcases,

thepurplewirewillonlyneedtobeconnectedtoonedoorswitch,nomatterhowmanydoorsthevehiclehas.

WARNING: Do not use the purple wire if the vehicle has ground output type door switches. (see

BROWNWIRE)

ORANGEWIRE: GROUNDOUTPUTWHENARMED

This wire is provided to control the starter cut relay. Connect the orange wire to terminal 86 of the relay and

wire the remaining relay contacts as shown in the wiring diagram.

IMPORTANT: Audiovox does not recommend using this relay to interrupt the ignition wire. Only

connectthis relay to the lowcurrent starter solenoid feed wire, as indicated on the

wiring diagram.

GREY&BLACK2PIN(blue)CONNECTOR:VALETSWITCH

Routethetwoconductor,blueconnectorfromthepreviouslyinstalledvaletswitchtothealarmcontrolmodule

and plug it into the mating blue connector on the end of the module.

RED & BLUE WIRES: DASH MOUNTED LED

Routethetwoconductor,whiteconnector(redandbluewires)fromthepreviouslyinstalledLEDtothealarm

control module and plug it into the mating white connector on the end of the module.

RED & GREEN 2 PIN (white) CONNECTOR: DOOR LOCK OUTPUTS

Thesewireswillprovide a pulsedgroundoutputto the factorydoorlockcontrol relay. Themaximumcurrent

drawthroughtheseoutputs mustnotexceed300 mA.

Page 4

3 Wire Ground Switched Door Locks

In this application, the red wire provides a ground pulse during arming (pulsed ground lock) output.

Connectthe redwire to the wire that provides alow currentground signal from the factorydoor lockswitch to

the factory door lock control relay.

The green wire provides a ground pulse during disarming (pulsed ground unlock) output. Connect the

green wire to the wire that provides a low current ground signal from the factory door unlock switch to the

factory door lock control relay.

3 Wire Positive Switched Door Locks

Inthis application,the red wire provides a positive pulse during disarming (pulsed + 12 volt unlock) output.

Connectthe red wire to thewire thatprovides alow current positivesignal fromthe factorydoor unlockswitch

to the factory door lock control relay.

The green wire provides a positive pulse during arming (pulsed + 12 volt lock) output. Connect the green

wireto thewire thatprovides alow currentpositive signalfrom the factory door lock switch to the factory door

lock control relay.

Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock

ControlCircuits

Theseapplications require the use ofadditional componentswhich may include relays, fixedresistors, or for

convenience,theAS9159Door Lock Interface. RefertotheAUDIOVOXDoor Lock WiringSupplementandor

theAudiovox fax backservice forinformation onyour particular vehiclefor properlyconnecting to these types

of circuits.

COMPLETING THE INSTALLATION

Antenna Wire : Besure to extend the thin black antenna wire to it’s full length and cable tie into place where

itcannot bedamaged. Avoidwrapping this wire around major,high current wire looms.

Adjusting the Shock Sensor : Thesensitivity ofthepre -detect circuit, whereused, is automaticallyset 30%

less sensitive than the full trigger circuit.

Using a small screwdriver, gently turn the adjustment screw fully counterclockwise. ( DO NOT over turn this

screw. Maximumrotation forthis adjustmentis 270° ). Close the hood and trunk lids, and armthe alarm.Wait

6 seconds for the accessories trigger zone to stabilize, then firmly strike the rear bumper with the side of a

closed fist considering the amount of force required to break a window.

CAUTION : Never perform this test on the vehicle’s glass, as you may break the window.

Turn the adjustment screw clockwise ( increasing sensitivity ) about ¼ turn and re-test. Repeat this

procedure until the alarm sounds. Ultimately, one firm strike to the rear bumper will cause the alarm to emit

pre- detect warning tones.

WARNING ! Setting the sensitivity too high can cause false alarms due to noise vibrations from passing

trucksandheavyequipment.Todecreasesensitivity,turntheadjustmentscrewcounterclockwise.

Wire Dressing : Always wrap the alarm wires in convoluted tubing, or with a spiral wrap of electrical tape.

Securethese loomsalong therouting using cable ties. This will ensurethat thealarm wiresare not damaged

byfalling ontohot or sharp moving surfacesin thevehicle.

Operation : Takeafew momentsto check offthe appropriate option boxesin theowner’smanual and tofully

explain the operation of the system to your customer.

Page 5

Autres manuels pour Prestige APS-25KB

Table des matières

Autres manuels Audiovox Alarme de voiture

Audiovox

Audiovox Prestige Platinum APS-350-A Manuel utilisateur

Audiovox

Audiovox Pursuit PRO-9642 Manuel utilisateur

Audiovox

Audiovox APS620 - Prestige Remote Start Manuel utilisateur

Audiovox

Audiovox Rampage AA-939 Manuel utilisateur

Audiovox

Audiovox Pursuit PRO-9675FT4 Manuel utilisateur

Audiovox

Audiovox APS-30 Manuel utilisateur

Audiovox

Audiovox Prestige Platinum APS-250-A Manuel utilisateur

Audiovox

Audiovox Prestige Platinum APS-998 Manuel utilisateur

Audiovox

Audiovox Prestige Platinum APS-510 Manuel utilisateur

Audiovox

Audiovox Pursuit PRO-9744 Manuel utilisateur

Audiovox

Audiovox AA-940 Manuel utilisateur

Audiovox

Audiovox PRO 9644 Manuel utilisateur

Audiovox

Audiovox Prestige Platinum APS-350-A Manuel utilisateur

Audiovox

Audiovox Prestige Platinum APS-700 Manuel utilisateur

Audiovox

Audiovox Prestige Platinum 128-8549 Manuel utilisateur

Audiovox

Audiovox PRESTIGE APS-20LAD Manuel utilisateur

Audiovox

Audiovox UltraGuard PRO 9549UG Manuel utilisateur

Audiovox

Audiovox Prestige APS-15KB Manuel utilisateur

Audiovox

Audiovox PRO9342FT3 Manuel utilisateur

Audiovox

Audiovox Rampage AA-929 Manuel utilisateur

Audiovox

Audiovox SECURIKEY+ Mode d'emploi

Audiovox

Audiovox AS-9495-4P Manuel utilisateur

Audiovox

Audiovox Prestige 5BLCR Mode d'emploi

Audiovox

Audiovox Platinum APS 500 Manuel utilisateur

Manuels Alarme de voiture populaires d'autres marques

Clifford

Clifford 3606X Manuel utilisateur

Ultra Start

Ultra Start 2500M SERIES Manuel utilisateur

Ultra Start

Ultra Start 650 Series Manuel utilisateur

Sparkrite

Sparkrite SRA8 Manuel utilisateur

Viper

Viper 4708V Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuel

Falcon

Falcon Predator XL3 Guide de l'utilisateur

Clifford

Clifford Sabre II Manuel utilisateur

CrimeStopper

CrimeStopper CS-8717 Guide de démarrage rapide

Ultra Start

Ultra Start 450 SERIES Manuel utilisateur

Scytek electronic

Scytek electronic Vectra X3 Manuel utilisateur

Excalibur

Excalibur AL-1860-EDPB Manuel utilisateur

Clifford

Clifford CYBER 2 Manuel utilisateur

Gemini

Gemini 7057 Manuel utilisateur

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuel utilisateur

Magicar

Magicar FAI-440 Manuel utilisateur

Clifford

Clifford Nova 3 Manuel utilisateur

Viper

Viper 560XV Manuel utilisateur