Audio Authority 1710A Manuel utilisateur
Instructions
Model 1710A
Headphone Demonstration
Switching Amplifier
Model 1710A shown with optional cover.
2
Liability Statement
Every effort has been made to ensure that this product is free of defects. Audio Authority cannot be held liable for the use of this hardware or any
direct or indirect consequential damages arising from its use. It is the responsibility of the user of the hardware to check that it is suitable for his/her
requirements and that it is installed correctly. All rights reserved. No parts of this manual may be reproduced or transmitted by any form or means
electronic or mechanical, including photocopying, recording or by any information storage or retrieval system without the written consent of the
publisher.
Audio Authority reserves the right to revise any of its hardware and software following its policy to modify and/or improve its products where necessary
or desirable. This statement does not affect the legal rights of the user in any way.
All third party trademarks and copyrights are recognized. The Audio Authority logo and Double A logo are the registered Trademarks of Audio
Authority. All other trademarks are the property of their respective holders.
POWER
INPUT
STATUS
LED
THEFT
BUZZER
POWER
OUTPUT
FEATURE
SWITCHES
CUSTOMER
INPUT
DEMO
TIMEOUT
HOUSE
PLAYER
SYSTEM
BUS
HEADPHONE
POSITION 1
HEADPHONE
POSITION 2
HEADPHONE
POSITION 3
HEADPHONE
POSITION 4
AUDIO
BUS OUT
SIREN
OUT
PRODUCT
SELECT
BUTTONS
1
2
3
4
RESET
SWITCH
THEFT
INDICATOR
THEFT
DETECTION
4
3
2
1
Introduction
The 1710A is designed to provide high delity amplication and theft detection for premium headphones,
and/or manual switching for self service retail demonstration. The 1710A has several options that govern
the behavior of the headphone demonstration. In distribution mode (see table on page 4), all outputs
are active all the time. In switching mode, only one of the four outputs may be active at any time. Larger
switching systems, linked by system bus and audio patch cords, can either allow one live position on each
1710A, or the entire system can be limited to one active position at a time (see feature switch settings).
Visit www.audioauthority.com/demobeat for tips and application diagrams.
1710AN pictured
(Model 1710A includes
the steel cover)
4 3 2 1
DISABLE ENABLE
3
Package Contents
Before attempting to use this product, please check the packaging and make certain the following items
are contained in the shipping carton:
• 1710A Headphone Demonstrator
• DC Power Adapter
• User Manual
Features
• High quality headphone amplication
• Switching or distribution behavior
• Adjustable demonstration timeout in switching mode
• Automatic selection of customer audio source when connected
• Theft detection and integral alarm
• Multiple units can easily be connected together for any size system
Audio Sources and Customer Auto Demo
Connect a music player to the PLAYER input jack as the default audio source. If desired, provide a
3.5mm cord connected to the CUSTOMER input so that customers may use their own music players to
demonstrate headphones. When audio is detected on the CUSTOMER input jack, the customer audio is
selected as the audio source. If no audio is detected on the CUSTOMER input for 7.5 seconds, the 1710A
switches back to the PLAYER input.
Bus Out
The bus output feeds the currently selected audio input (player or customer) to more 1710A modules or
other audio devices in the system. Connect a 3.5mm patch cord from the rst 1710A bus output to the
second 1710A player input, etc. One linked system sharing a house player also must share one customer
input (do not use any customer inputs besides the rst 1710A).
System Bus
System Bus is a four-conductor cable that allows multiple 1710A modules to be connected and
communicate with each other. They can coordinate current product selection as well as alarm signals
and alarm reset (see Theft Detection on page 4).
Button (PSB) Ports
In switching mode, customers can activate one product at a time using a two-wire momentary switch.
Connect a switch for each corresponding product. The LED in the switch illuminates during the
demonstration. Buttons are not used in distribution mode.
Note: Please retain the original packing
material in case the unit must be returned.
If you nd any items are missing, contact
Audio Authority immediately. Have the Model
Number and Invoice available for reference
when you call.
2048 Mercer Road, Lexington, KY 40511-1071 USA
800-322-8346 • 859-233-4599 • Fax: 859-233-4510
support@audioauthority.com • www.audioauthority.com
752-666 Rev. 20130830
Theft Detection
1710A theft detection is compatible with most headphone models, including models with active circuitry
such as noise cancelling. Activate theft detection using feature switch #3. The 1710A can detect most
devices when connected directly to the 1710A. If not, you must connect the product through an Audio
Authority extension cable. All devices should be tested for proper detection behavior upon installation. If
detection does not work for a particular device, disable detection for that port using the Theft Detection
switches.
Attach a reset switch (contact closure) to reset the alarm. We recommend that a remote theft indicator
light should be installed in clear view of customers. The blinking LED is a deterrent, warning that theft
detection is active. The on-board buzzer sounds if it detects an unauthorized removal, but If a louder
alarm is desired, the external siren port can power a 12VDC siren.
When active, the theft indicator blinks and the 1710A detects the headphones that are connected, and
triggers the alarm if one is removed. The theft indicator light connected to the 1710A where the stolen
headphones were connected shines solid until the alarm is reset.
When headphones must be connected and disconnected, turn on the siren reset switch, make product
changes, and turn the switch off again. The theft indicator LED(s) turn off when the reset switch is on.
Only one reset switch is needed per system; reset status is communicated to all other modules that are
connected via System Bus.
Timeout Interval
In switching mode, a demo timer is initiated each time a customer selects a product output to audition.
The demonstration length is set by the timeout switch, in increments of 15 seconds. If the timeout switch
is set to 0, then the demonstration does not time out.
Feature Switch Settings
Switch Off (up position) On (down position)
1 Gain = 0dB Gain = 6dB
2 One active product per board One active product per system
3 Theft detection off Theft detection on
4 Switcher mode (one on) Distribution mode (all on)
Operation
On power up, the status light blinks to show normal operation, and selector buttons are lit. When
customer audio is playing, the Status light blinks rapidly.
Table des matières
Autres manuels Audio Authority Amplificateur
Audio Authority
Audio Authority Distribution Amplifiers 985DTO Mode d'emploi
Audio Authority
Audio Authority 1710A Manuel utilisateur
Audio Authority
Audio Authority 1816 Manuel utilisateur
Audio Authority
Audio Authority ADX-1616 Manuel
Audio Authority
Audio Authority AMP-1235 Manuel du propriétaire
Audio Authority
Audio Authority DTV Manuel utilisateur
Audio Authority
Audio Authority 985U Mode d'emploi
Audio Authority
Audio Authority 1398D Manuel utilisateur
Audio Authority
Audio Authority Sona Flex SF-16B Mode d'emploi
Audio Authority
Audio Authority SF-16M Manuel
Audio Authority
Audio Authority 985DTV Mode d'emploi
Audio Authority
Audio Authority 1185ci Manuel utilisateur
Audio Authority
Audio Authority Ascentic 1399 Manuel utilisateur
Audio Authority
Audio Authority ADX-0808 Manuel utilisateur
Audio Authority
Audio Authority 975A Manuel utilisateur
Audio Authority
Audio Authority 1394A Manuel utilisateur
Audio Authority
Audio Authority 1710B Manuel utilisateur
Audio Authority
Audio Authority 1816-1 Manuel utilisateur
Audio Authority
Audio Authority CMX-144 Manuel du propriétaire
Audio Authority
Audio Authority 9850 Mode d'emploi
