AtVideo HCPM230W Manuel utilisateur
Before installing and using this product, please read the instructions fully and carefully,
And be sure to keep it handy for late use.
Printed In Korea
50304217A
DIMENSIONS
62(2.44”)
96(3.78”)
174(6.85”)
85(3.35”)
96(3.78”)
126(4.96”)
85(3.35”)
116(4.56”)29(1.14”)
145(5.70”)
96(3.78”)
116(4.56”)
186(7.32”)
70.5
(2.78
”)
131.2
(5.16
”)
60.7
(2.39
”)
Pole
Corner
HCPM230W
POLE & CORNER MOUNT BRACKET
Prior to Use
Avoid installing the mount onto an unstable structure such as a gypsum wall panel.
Install the mount onto a strong structure such as a concrete wall, steel beam, etc.
Confirm that the following parts are included.
Use concrete screws with plugs or other installation tools when installing the mount onto
a concrete structure, make sure that all the screw parts are metallic.
(Avoid screwing too close to the edge of a piece of wood when screwing into a wooden structure)
Composition
Mounting to the poles or the corners of building structure.
Feed the hose bands through the vertical stills
located on the four corners of the mounting flaps
as shown below. Wrap the hose bands around
the pole like structure then use the driver to rotate
the screw that is attached at the end of the hose
bands clockwise. Rotating the screw shortens the
bands thereby fastening the around the structure.
Composition
Pole & Corner Mount Instruction Manual Stainless Hose Band(2pcs)
Plastic Anchor(D6)
6pcs
Screw Tapping
BH 6x50L Stainless
6pcs
Screw Machine(SEMS)
PH M6x25L Stainless
4pcs
Screw Machine(SEMS)
PH M8x35L Stainless
4pcs
Nut
M8 Stainless
4pcs
Using the pole & Mount as a template,
mark the locations of the six screw
holes where the mounting adaptor will go.
Install the plastic anchors(D6) at the
six pre-marked locations. Use the screws
with washers to affix the mount adaptor
to the corner of a building structure.
Using the appropriate screws and nuts
supplied, affix the power box base to the
pole & corner mount at the four corners
of the mounting surface.
Mounting the power box or wall mount to the pole & corner mount.
Using the appropriate screws supplied,
affix the power box base to the pole &
corner mount at the four corners of the
mounting surface as shown the below.
Using the appropriate screws and nuts supplied, affix the wall mount to the pole & corner
mount at the four corners of the mounting surface as shown the below.
A
Screw Machine(SEMS)
PH M6x25L
Screw Machine(SEMS)
PH M6x25L
AC
Screw Machine(SEMS)
PH M8x35L & Nut M8
B
Stainless Hose Band
D=260mm(10.24inch)
Screw Machine(SEMS)
PH M6x25L
B
Screw Machine(SEMS)
PH M8x35L
Nut M8
C
Screw Machine(SEMS)
PH M6x25L
Beforeinstalling and using this product, please read the instructions fully and carefully,
Andbe sure to keep it handy for late use.
HCPM230W
POLE & CORNER MOUNT BRACKET
Plastic Anchor(D6)
Screw Tapping
BH 6x50L Stainless
Autres manuels AtVideo Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
