ATS W500 Wildlink Manuel utilisateur

1 02.25.15

W500 Wildlink GPS Small Collar Logger/

W510 Wildlink GPS Glue-on Logger

User’s Manual

IMPORTANT: Your W500 Wildlink Small Collar Loggers or W510 Wildlink Glue-on Loggers

HAVE NOT BEEN PROGRAMMED for operation. You must program each unit in order for

them to function.

2 02.25.15

Table of Contents

Section 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

Section 2 Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . 4

Section 3 Using ATSFixes for Loggers . . . . . . . . . . . . . . . . . 5

Section 4 Operating the GPS Logger . . . . . . . . . . . . . . . . . . . 8

Section 5 Downloading Data from the GPS Logger . . . . . . . 9

Section 6 Power-On Self Test . . . . . . . . . . . . . . . . . . . . . . . . . 12

Section 7 Data Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Section 8 Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . 13

3 02.25.15

Section 1 Introduction

Thank you for purchasing an ATS W500 Series Wildlink Small Collar Logger or Glue-on

Logger. The GPS model you have received has not had a fix schedule program downloaded to it.

You will need to load a fix schedule program into the Logger to control its operation. The

software you received with the GPS logger, ATSFixes for Loggers, guides you through this

process. Complete help documentation is available within the different software pages, indicated

by the icon. Click on the icon for help details.

The magnet you see attached to the Logger keeps it running at a lower current. When you are not

using your logger, leave the magnet attached.

The GPS logger is supplied with a Wildlink model W100 communication module, PN 17621

(Figure 1). The Wildlink module enables the GPS logger to communicate with a PC for

programming and data uploads via a wireless link.

Figure 1. ATS Wildlink model W100 communication module, PN 17621 (with USB cable)

IMPORTANT: Your W500 Wildlink Small Collar Logger/W510 Wildlink Glue-on Logger

HAS NOT BEEN PROGRAMMED for operation. You must program the logger for it to

function.

4 02.25.15

Section 2 Theory of Operation

The ATS W500 Series Wildlink models consist of five different assemblies:

1) the collar belting, or attachment mechanism, 2) an electronics housing, which is attached

to the collar belting, 3) a VHF antenna, 4) a GPS antenna, and 5) a UHF antenna

The electronics housing consists of a battery pack, a VHF transmitter, like those found on

traditional VHF beacon collars, a GPS receiver chipset and a UHF communications IC. Each has

its own antenna, as noted above.

The logger is shipped with a magnet taped into place with yellow vinyl tape. While the magnet is

attached to the logger, it is running at the lowest current drain possible. Removing the magnet

from the logger starts a UHF communication attempt. The logger activates its wireless UHF

communication mode and waits to receive wireless commands from the W100 for a period of 40

seconds. After the 40 seconds, an automatic 5 minutes of VHF double beeps regardless of the

logger’s program.

The GPS Logger stores all location data in the flash memory of its electronics. Location data

may be retrieved wirelessly by PC via the Wildlink W100 module either downloaded nearby with

a magnet swipe on the logger activating the communication link, or a time scheduled remote

download (No magnet swipe used) if selected as an option when programming the logger.

The VHF transmitter is used to locate the animal in order to retrieve the logger. The logger may

be refurbished at ATS’s facility.

The W500 Wildlink Small Collar Logger does not come standard with a drop-off mechanism to

break the collar off of an animal. However, the optional Sure-Drop mechanism may be

purchased separately from ATS and attached to the collar to provide a drop off capability.

5 02.25.15

Section 3 Using ATSFixes for Loggers Software

Installing ATSFixes for Loggers Software

To install ATSFixes for Loggers Software, double click on the setup.exe file found on the CD

supplied with your equipment. The software installs on your computer, and you can find it later

under the programs list on your computer.

The installation for the ATSFixes for Loggers software creates some folders on the C: (hard)

drive of your computer. Once you have created a program and uploaded it to a logger, two files

are created and added to the folders. The files contain all the information for the program that

was uploaded to a logger, including the serial number of the logger. If you ever have doubts

about how you programmed a logger or what VHF frequency the logger is transmitting on, you

can look up the information in these files. These files are stored in the C:/Advanced Telemetry

Systems, Inc./GPS/GPS_LOGGER_PROGRAMS folder.

Wildlink W100 Module Setup

The Wildlink module driver must be installed prior to using ATSFixes for Loggers to program

the W500 Wildlink Small Collar Logger/W510 Wildlink Glue-on Logger. To install the driver,

double click on the executable found in the supplied CD that pertains to your PC:

-CP210xVCPInstaller_x86 (Windows XP, Windows Vista, Windows 7, and Windows 8 32bit

systems)

-CP210xVCPInstaller_x64 (64 bit systems)

-CP210x_VCP_Win2K (Windows 2000)

Follow the instructions on the screen. Restart your computer if necessary.

Programming Your GPS Logger

The program you create for the GPS logger will control the GPS fix schedule, VHF transmitter

operation and wireless communication which is tied to the VHF schedule if selected as an option

in the programming. All settings are the same for each year i.e. different years cannot have

unique program schedules.

Saving GPS Programs

If you have several loggers that need to be programmed using an identical program, you may

compose and save a program, and load it into additional loggers. Once a program has been

saved, it is listed under the GPS Logger Programs. Simply choose the program that you wish to

load into the loggers.

6 02.25.15

Life Estimation

The ATSFixes for Loggers Programming Software estimates the life that you can expect from

your GPS Logger. If you need more life from your GPS logger than what is estimated, you can

go back and adjust the program to give your GPS logger a longer life. If adjustments are made,

the life calculation is recalculated when the type of battery used is selected again. You might

decide to take fewer fixes each day, or you might program the VHF beacon to operate on a

limited basis, also called a transmitter duty cycle.

Note: Calculations for life estimates assume that the batteries are new.

Steps to Start GPS Logger Programming

Figure 2. ATSFixes for Loggers

To load a program into the GPS logger, the Wildlink W100 module needs to be connected (via

USB port) to the PC running the ATSFixes for Loggers software and the logger needs to be

within one meter of the Wildlink module. If you are only creating a program to be saved for later

7 02.25.15

use, then having either/both device(s) is not necessary. Note: Remove magnet prior to

programming.

1. Open the ATSFixes for Loggers Software. It will look similar to Figure 2. The software

recognizes all serial ports available when starting. Note: The software will not proceed

without an available COM port.

2. For the Serial Port option select the COM port associated with the Wildlink module. A

guess and check may be used to determine the correct COM port to use (not preferred) or

Windows’Device Manager tool can be used to determine which COM port should be

selected. The Wildlink module will be associated with whichever port the ‘Silicon Labs

CP210x’COM port is listed under.

3. Click on the Program GPS Logger button to start creating a program. If you are copying a

previously stored program then you need to pick that program from the list of programs.

Otherwise the GPS Logger Program should be New Logger Program for new loggers.

4. Fill in the information in each step of the ATSFixes for Loggers software. Each screen

has a Help button, if needed. Note that no offset exists to distinguish between standard

time and daylight savings time. Even if your study area has daylight savings time during

all or part of your study, the resulting data results are without daylight savings time taken

into account.

5. After the fix schedule program has been configured with the ATSFixes for Loggers

Software, it needs to be loaded into the GPS Logger. To start this process, click on the

Program Logger button in the Step 3: Life, Activity Data window. Click OK on the

following dialog box and then touch the magnet to the logger at the location of the 2

white dots and remove. Touching the magnet to the logger tells the logger that the PC

will be sending information to it.

6. When the GPS Logger is done loading up the user's program, there is a beep and a

message to the PC's screen.

Reprogramming a GPS Logger

If you want to change the program, you need to first erase the current program (and any stored

data). Use the Erase Data/Program button to erase the program and data before reprogramming

it. Be sure that you have first downloaded any stored data you wish to keep.

8 02.25.15

Section 4 Operating the GPS Logger

Interpreting the VHF Beacon Beep Patterns

The GPS logger includes a VHF transmitter that can be used to locate it and/or determine its

status. The VHF transmitter can be scheduled to run continuously or only during certain hours of

the day. It can be programmed to stay off for up to 23 hours each day in order to extend life. The

VHF transmitter also has some obligatory beep patterns which you hear regardless of whether

the transmitter was scheduled to be active or not.

The different beep patterns the VHF transmitter uses are based on either a 48 pulses per minute

(ppm) rate, or a 27 ppm rate. To your ear, 48 ppm sounds like one beep per second. The 27 ppm

rate sounds like one beep per every two seconds. Some beep patterns have double or triple

pulses, which are used to indicate various operating conditions to the listener.

If the VHF transmitter is scheduled to operate, the logger operating condition is indicated

by the beep patterns below:

Normal VHF = 48 ppm.

Mortality VHF = 27 ppm (double pulse and then single pulse, repeating).

Last GPS fix successful = Normal VHF (48 ppm) with a double pulse on the 6th pulse.

Last GPS fix failed = Normal VHF (48 ppm).

Obligatory beep patterns (do not follow the scheduled duty cycle) indicate the following

operating conditions:

Reset/Startup/Not programmed = Slow triple pulse and then single pulse at 48ppm.

After pulling off magnet = Initially a 40 second period of no VHF, as the logger activates its

UHF mode, and stays in that mode attempting for a UHF wireless communication link first, then

after the 40 second period double pulse VHF at 48 ppm for a period of 5 minutes only. After the

5 minutes have elapsed, the logger reverts to its regularly scheduled VHF beep pattern.

Low Battery condition = triple pulse at 27 ppm, continuously (much slower than normal VHF

beep pattern).

Note: The VHF transmitter does not operate while the logger is downloading a program,

obtaining GPS fixes, or uploading data to a PC.

9 02.25.15

GPS Operation

During a GPS fix attempt, the VHF transmitter is silent. A GPS attempt may last as long as the

setting that was selected during programming but may also be shorter depending on the logger’s

view of the sky. Whether the fix attempt was successful or not is indicated by the VHF beep

pattern that follows the attempt. You will only hear these beep patterns if the VHF transmitter

was scheduled to beep during this time.

Mortality

If you choose to use mortality when you program the logger with the ATSFixes for Loggers

software, the VHF will change to the Mortality VHF and, if a duty cycle was created during

programming, follows the duty cycle until activity is detected or a higher priority event occurs

(low battery).

In order for the GPS logger to exit mortality mode, the logger must undergo thirty seconds of

activity. (The thirty seconds of activity does not have to be consecutive but should be within the

mortality period chosen.)

Light Sensor

This is an optional sensor added to the logger. With this option selected and the optional light

sensor installed on the logger, a low light condition prevents the logger from taking a scheduled

GPS fix. This is for cases where it is known that the animal will be at times sheltered from a

clear view of the sky (i.e. in a burrow). By not allowing a scheduled GPS fix in this condition,

the battery life is extended from excluding unnecessary GPS fix attempts.

Section 5 Downloading Data from the GPS Logger

Once GPS position data have been stored in the GPS logger memory, they can be downloaded to

your computer. Note that during data download, the VHF transmitter is silent even if it was

scheduled to beep. There are two download buttons. “Download Data”is for downloading with

the logger nearby and communication from the logger is activated with a magnet swipe. The

“Remote Download”button is to download data in the field while the logger is still attached to

the animal. This option needs to be selected in the programming to be activated. If remote

downloading is not needed, deselect this option button, and more battery life will be available.

10 02.25.15

Steps for Downloading Data

A) Download Data Button

1. Connect the ATS Wildlink module to a USB port on the PC.

2. Open the ATSFixes for Loggers Programming Software.

3. Click the Download Data button.

4. Choose between Degrees, Decimal Minutes and Decimal Degrees for the data format of

the GPS data.

5. Click the Continue button.

6. Touch the magnet to the GPS Logger to initiate communication.

B) Remote Download Button (note: the logger needs to have the remote download

option selected when the logger was programmed)

1. Connect the ATS Wildlink module to a USB port on the PC.

2. Open the ATSFixes for Loggers Programming Software.

3. Click the Remote Download button.

4. Choose between Degrees, Decimal Minutes and Decimal Degrees for the data format

of the GPS data.

5. Click the Continue button.

6. Wait for a download. The W100 continuously transmits a signal and waits for a reply

from a logger. The logger attempts a wireless communication every 11 minutes after

the hour.

If the Remote Download option was selected in the programming of the logger, the logger will

activate the UHF mode every multiple of 11 minutes after the hour (i.e.:11,:22,:33,:44,:55) for a

2 second period. Every multiple of 11 minutes was chosen to prevent a wireless link interruption

during a scheduled GPS fix. The UHF remote communication link is tied to the VHF schedule,

and is not active if the VHF is not active. If the logger is in hand, and the VHF was scheduled to

be off at the time, a magnet swipe still activates a wireless download via the Download Data

button. After a download, the logger continues its programed schedule and prevents a UHF

wake up for 20 minutes. This is to prevent re- downloading of the data if multiple loggers are in

the same area. If there are other loggers in the same area, they all know a download attempt has

been made. The loggers which did not get a download command will then go into a faster 1

minute interval to wake up for a UHF download for a 10 minute period. After the 10 minute

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ATS Enregistreur de données

ATS

ATS Accu-Time 3610 Series Manuel utilisateur

Manuels Enregistreur de données populaires d'autres marques

TESTO

TESTO 176 Manuel utilisateur

HT Italia

HT Italia XL421 Manuel utilisateur

HBM

HBM SOMAT XR CX22B-R Manuel utilisateur

Agtrix

Agtrix 380i Manuel utilisateur

Hobo

Hobo H8 Pro Manuel utilisateur

Beijing ART Tech

Beijing ART Tech PCI2320 Manuel utilisateur

Athena

Athena GET SL1 Manuel utilisateur

Motec Systems

Motec Systems C185 Manuel utilisateur

Beijing ART Tech

Beijing ART Tech USB2832 Manuel utilisateur

Rotronic

Rotronic HygroLog HL20 Manuel utilisateur

MRC

MRC DW-6092 Manuel utilisateur

Racelogic

Racelogic VBOX LapTimer Manuel utilisateur

Edu-Logger

Edu-Logger 900-240 Manuel utilisateur

Elma

Elma DT173 Manuel utilisateur

MadgeTech

MadgeTech PRTemp140 Fiche technique

Comet

Comet U0121M Manuel utilisateur

pico Technology

pico Technology PT-104 Manuel utilisateur

Soil Instruments

Soil Instruments GTecLink Manuel utilisateur