Atmos MissionOne Manuel utilisateur
© ATMOS Co., Ltd. All rights reserved.
V2-20190526
1. Introduction 3
MISSION ONE Feature 3
2. Basic Operation 3
2.1. Turning On/Off 4
2.2. Charging 4
2.3. Buttons 4
2.4. Diving Safety 4
2.5 App Pairing 5
2.6 Unpair 5
2.7 Smart Notification (iOS) 5
2.8 Sync Log 5
2.9 Firmware Update 6
3. Watch Mode 6
3.1. No Fly Time and Surface Intervel 6
3.2. Stopwatch 7
3.3. Enter Water Auto-on 7
4. Scuba Mode 7
4.1. Display Layout and Alerts 7
4.2. NITROX 11
4.3. Dive Planner 11
4.4. Conservatism 11
4.5. Advanced Setting 11
5. Freedive Mode 12
5.1. Display Layout and Alerts 12
5.2. Time Alarm 14
5.3. Depth Alarm 14
5.4. Stopwatch 14
5.5. Advanced Setting 14
6. Gauge Mode 15
6.1. Display Layout and Alerts 15
6.2. Bottom Timer 16
6.3. Advanced Setting 16
2
7. GPS and Compass 17
7.1. Mark Entry/Exit GPS coordinate 17
7.2. Dive Site Guide 17
7.3. Compass Calibration 17
8. Warranty & Maintenance 18
8.1. Screen Guard 18
8.2. Watch Strap 18
8.3. Storage and Maintenance 18
8.4. Warranty 18
8.5. Specification 20
1. Introduction
Mission One is a powerful and intelligent dive computer
for scuba and free diving enthusiasts. Its advanced
alarm system provides instant vibration and intuitive
display notification. Equipped with GPS and digital
compass make users stay oriented underwater and
meanwhile upload dive site’s GPS location to ATMOS’s
divelog App above surface. Robust and sleek, it’s the
most desirable dive companion to ensure professional
and recreational divers the best diving experience.
MISSION ONE Feature
❖4 Modes: Air｜Nitrox｜Freedive｜Gauge
❖Water resistance: 100m (10ATM)
❖Decompression algorithm: Bühlmann ZHL-16c
❖High-res 1.2”color display (Sunlight-visible)
❖Super intutive user interface
❖Easy to read screen and big layout display
❖Multilanguage
❖Constant backlight
❖Vibration alarm
❖Digital compass
❖GPS dive site guide
❖Graphical dive logs
❖App digital logbook
❖Smart notification (iOS supported, Android coming soon)
❖Rechargable: Up to 40 hours dive time (Backlight off)
❖Firmware updateable
❖90g lightweight
❖Silicone strap (24mm width compatible)
3
2. Basic Operation
2.1. Turing On/Off
Turing On: Hold Button D (bottom-left) for 3 sec.
Turing Off: Hold Button D (bottom-left) for 3 sec in watch
mode.
2.2. Charging
Please make sure the charging point are dry and clean.
It requires 2 hours to fully charge the MISSION ONE.
(Power input : DC 5V/2A)
2.3. Buttons
2.4. Diving Safety
● Pleaser read this manual thoroughly and make
sure you understand the operation, display,
limitation of the MISSION ONE.
● All dive gears will fall. It is not whether it will fall
but when it will. Firmware may have bug, too. Do
not use the MISSION ONE as your only source
of information. Have a backup computer and do
dive plan before each dive.
● Diving has risk. Only trained diver should use the
MISSION ONE. Do not use the MISSION ONE in
any dive beyond your certification level.
● MISSION ONE is designed for recreational
diving. Do not use it in commercial diving.
● It is assumed that the diver's ascent rate is
10m/min(33ft/min). Ascending significantly faster
than this will impact decompression calculation.
● Please follow the decompression stops advised
by MISSION ONE. Violation will increase the risk
of decompression sickness, which may lead to
serious injury or death.
4
● Do not throw, collide, press the MISSION ONE.
Do not expose MISSION ONE under the sunlight
or left it in a car under sunlight.
2.5. APP Pairing
Use ATMOS App to sync dive log, update
firmware.
1. Download the ATMOS App:http://l.ead.me/atmos
2. After logging, go to“Your device”, select “Start
Pairing”.
※Enable bluetooth of the mobile phone, Android
may need to authorize the connection of the
device.
3. MISSION ONE: SETTING -> CONNECT ->
CONNECT APP : ON
4. ATMOS App: Select the device with the correct
bluetooth number. (Bluetooth number“xxxx”= the
4 numbers of the serial number of your MISSION
ONE)
5. ATMOS App: : Enter the 6 Pin Codes shown on
MISSION ONE. Connected!
2.6. Unpair
1. MISSION ONE SETTING ->CONNECT
->UNPAIR: YES
2. ATMOS App: Select your device, press
upper-right button: Delete.
3. Your mobile phone: Bluetooth > delete the device
2.7. Smart Notification (iOS)
Smart Notification allows MISSION ONE to show
the message and phone call from the paired
mobile phone.
Eanble Smart Notification:
●MISSION ONE: SETTING -> CONNECT ->
CONNECT APP : ON
●NOTIFICATION: ALL / CALL ONLY / OFF
2.8. Sync Log
Sync the dive logs from MISSION ONE to
ATMOS App.
●ATMOS App: Press the sync button on the right
side in the page of Your Device.
5
※Syncing log requires stable internet signal.
2.9. Firmware Update
ATMOS regularly release new Firmware
including new feature, bug fix and improvement.
Keep the Firmware of your MISSION ONE the
latest.
※Updating Firmware requires stable internet
signal.
1. Via USB cable (suggested):
a. Get Firmware Tool from
https://www.atmos.app/support/
(Win10/Mac)
b. Install, then run Firmware tool.
c. Connect MISSION ONE with the charging
cable.
d. Press Update Firmware button.
2. Via ATMOS App(OTA):
a. Select your device in the ATMOS APP.
b. Press Upgrade button if there’s a new
version.
※Due to the signal of bluetooth may be
interfered by other devices nearby. Please use
the PC/Mac tool to update the firmware via USB
cable if there is abnormal behavior on MISSION
ONE after App update.
3. Watch Mode
3.1. No Fly Time and Surface Intervel
Due to residual nitrogen in body after diving. Please wait
until the No Fly Time disappears then take flight.
※Upper-right: Surface Intervel (S.I.) starts from the
moment exit water in last dive.
※Upper-left: No Fly Time Icon. Counting down by 24hr
from the moment exit water in last dive.
6
3.2. Stopwatch
Stopwatch
Hold Button C (Bottom-right)
for 2 seconds in watch mode
▶ Start: Press Button B.
▶ Stop: Press Button A
▶ Reset: Press Button B
when stopped
▶Return: Hold Button C for 2
seconds.
3.3. Enter Water Auto-on
The default dive mode of auto-on is Scuba Mode.
Default dive mode is changable in SETTING.
!!!Do not rely on auto-on function. It's important to
check all settings of the dive computer prior to descent in
each dive.
4. Scuba Mode
4.1. Screen Layout and Alerts
Predive
Upper-left: Compass degree
Left: Ascent rate bar
Mid-left: Water temp.
Upper-right: No
decompression limit (NDL)
Right: Current depth
Bottom-right: MOD -
(Maximum Operation Depth)
Bottom-right: 21% = AIR /
22-40% = NITROX
※Press Button B (Right)to
access Advanced Setting.
※Hold Button B (Right) for 3
seconds to enter mark
compass heading fuction.
7
During Dive
Upper-left: Compass degree
Left: Ascent rate bar Red=
faster than 10m(33ft)/min.
Left: Water temperature
Upper-right: NDL (No
Decompression Limit)
Mid: Current depth
Bottom: Dive time
※Press Button C
(Bottom-Right): View current
time, max depth, avg depth.
※Press Button D
(Bottom-Left): Turning backlight
On/Off.
※Hold Button D (Bottom-Left):
Change backlight brightness
level.
Mark Compass
Heading
Hold Button B (Right) to enter
mark compass heading fuction.
Press Button A (Upper-right):
Mark heading degree
Press Button B (Right):
Return
Press Button C
(Bottom-right): Unmark
Fast Ascent
Alert user if ascend too fast.
(Ascending rate exceeds
10m(33ft)/min for 5 seconds)
8
Time Alarm
Notify when dive time is
reached.
Depth Alarm
Notify when depth is reached.
Safety Stop
Safety Stop will appear when
ascend to 6m(20ft) if the max
depth of the dive is over
10m(33ft).
NDL will be replaced by a
3mins countdown.
Safety Stop Pause
Ascend above 3m or descend
below 7m during a safety stop.
Safety Pause will show and the
countdown will pause.
Safety Stop Clear
Notify when safety stop is
completed.
NDL below 3mins
Notify every minute when NDL
is below 3 mins.
9
Decompression Stop
Needed
Decompression stops are
mandatory stops that
must be followed in order to
reduce the risk of
decompression illness (DCI)
The “6m” indicates the stop
depth.
The “3' "indicates how much
time the stop is. (Minute)
Please stay close to the stop
depth until finish all deco stops.
Missed Stop
Alert when ascend above the
deco stop depth.
MOD
MOD is the maximum
allowable depth of the current
breathing gas as determined by
PPO2 limits.
Must ascend when seeing
MOD alarm.
CNS Alarm
Alert when central nervous
system toxicity loading
percentage greater than 85%.
Must ascend when seeing CNS
alarm.
Battery Low
Notify when battery power is
below 20%.
10
Table des matières
Autres manuels Atmos Instrument de plongée
