Atlantic 36835516 Manuel utilisateur
Item #36835516
Infinity TV Stand with Mount
THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION, PLEASE
READ AND KEEP FOR FUTURE REFERENCE.
Fits PLASMA or LCD TV’s THAT MEASURE 37 to 42 inches. If parts are missing, DO NOT return to
the store.To order missing / replacement parts or assembly assistance please
Lot Number:
Date:
-1-
Assembly Tips:
Become familiar with the instructions and all parts.
Make sure that all parts are in the box and in good condition.
Assemble the product on the open flat carton or a rug to protect the product and
your floor.
Some heavy products need a second person to assist in the assembly.
.
Use of power tools is not recommended.
Caution:
Never let children climb on furniture or play with furniture.
Do not sit or stand on furniture.
Do not overload shelves.
Use care when moving furniture. Furniture can tip over if moved improperly.
Only move furniture when it is empty of TV or other electronic components.
Care Instructions:
Use electrostatic dust cloths to clean furniture.
Do not set hot or cold containers directly on the furniture surface.
!
It is strongly recommended that at least two people carry out the assembly.
Do not place aTV that is heavier than the recommended load rating on the
furniture surface.
Do not install on sloping surface.
Assemble the product close to a wall.
With each step, first insert and hand-tighten all bolts and screws by hand. After ALL
BOLTS
are slightly screwed in, fully tighten bolts with Phillips screwdriver in sequential
pattern (clockwise or counter clockwise).
Improper handling can result in cuts and lacerations.
Screwing wall anchor into stud is very important to secure the stand.
A
B
C
D
E
1
1
1
H
G
1
1F
Components parts list
Item Qty
Part List
-2-
3
3
2
8
4
Components parts list
Item
Qty
I12
2
J
K
L
M
N
6
15
O
P
5
1
Tool needed (not included)
Q
R
S
1
1
1
1
T
1
A
B
C
1-Attach frames (B) & (C) to the back panel (A) with screws (J).
J*8
2
D
D
D
BC
I*12
2-Fasten beams (D) to the frames (B & C) with screws (I).
-3-
-4-
3
3-Place pads (N) on the beams (D) and frames (B & C). Apply pads (O) at the
bottom of the unit.
N*15
O*5
C
B
D
D
D
4
4-Attach holder (F) to panel (A) with screws (L). Place glass (E) on the pads.
A
F
L*4
E
E
E
-5-
E
E
E
5
5-Fast
en the glass (E) on the beams with screws (M). Do not over tighten screws.
M*6
6
6-Fasten two TV mounting brackets(H) on the back panel of the TV. Detail
assembly instructions refer to next pages.
H H
PAY EXTRA CARE AND ATTENTION TO THIS STEP. MAKE SURE THE
APPROPRIATE MOUNTING HARDWARE IS BEING USED PROPERLY.
1. Select correct Mounting Hardware according to the screw hole size on your TV, discard any remaining
Machine Screws or Spacers.
2. Carefully lay your Plasma/Flat Panel TV on its Face on a non-abrasive surface, making sure to lay
padding undermeath it so as not to damage the screen.
3. Place left Mounting Rail and Right Mounting Rail in the appropriate position, making sure they are
CENTERED on the back of the TV and LEVEL with one another.
MOUNTING HARDWARE LIST
HARDWARE
IDENTIFICATION
U1
U2
U3
V1
V2
V3
W3
W2
W1
PICTURE SIZE
(mm)
T1
T2
T3
4 x 15
4 x 35
4 x 54
5 x 54
6 x 54
8 x 15
8 x 35
8 x 54
5 x 35
5 x 15
6 x 15
6 x 35
HEAD DIAMETER
(mm)
8
8
8
8
8
8
10
10
10
14
14
14
- 6 -
Ø8
Ø6
X
Ø5
Ø4
7
- 7 -
For Flat Back TV
X
X
X
X
X
X
(T1~T3 Screws) (U1~U3 Screws)
(V1~V3 Screws) (W1~W3 Screws)
NOTE:The position of the Mounting Brackets and Hardware will be determined
by the type of TV that you have. These diagrams are not designed to
show the exact positioning; they are only to be used as a guide.
SECURE MACHINE SCREWS FULLY, BUT DO NOT OVER-TIGHTEN.
7-Insert Machine Screws through Dual-Hole Washers (X)
then into appropriate hole locate on left and right mounting brackets(H), and then into
TV.
X
X
Ø6 Ø8
Ø4 Ø5
(see Mounting Hardware list),
-8-
7-A
H
side view
F
8-After mounting the brackets (H) to TV, hang TV onto holder (F), see (7-A).
8
9
9-Attach holder (G) to bracket (H), fix holder (G) and wall strap(S) to panel (A) with washer(T) and
screws (K).
G
A
K*2
H
s
T
10
- 9 -
wall strap
wall
(S)
Tool needed(not included)
10- Place wall strap (S) at desired position on the wall. Mark the hole position with a pencil. Drill a hole
Note:Screwing wall anchor into stud is very important in properly securing the stand.
R
Q
(Q) (R)
on the pencil mark made on the wall with a 10mm size Drill Bit. Insert plastic anchor(Q) into the wall.
Fasten the wall strap(S) to the wall by inserting screw(R) through grommet in nylon strap(S) and then
into wall anchor.
Table des matières
Autres manuels Atlantic Support et étagère
Atlantic
Atlantic 77335799 Manuel utilisateur
Atlantic
Atlantic 77305018 Manuel utilisateur
Atlantic
Atlantic 63607232 Manuel utilisateur
Atlantic
Atlantic 63607145 Manuel utilisateur
Atlantic
Atlantic 45506118 Manuel utilisateur
Atlantic
Atlantic Quattro 75435504 Manuel utilisateur
Atlantic
Atlantic Metro 36835513 Manuel utilisateur
Atlantic
Atlantic Speaker Stand 050202 Manuel utilisateur
Atlantic
Atlantic Urb SPACE 23308046 Manuel utilisateur
Atlantic
Atlantic Typhoon 82635716 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
