Atlantic SOLCC2 Manuel utilisateur

1-877-80-PONDS

www.atlanticwatergardens.com 1-877-80-PONDS

www.atlanticwatergardens.com

Operating Manual

Color Changing

Lighting

Includes Models:

SOLCC2

SOLCC6

SOLCCLR

SOLCCMX3

SOLCCEXT

Introduction

Thank you for purchasing Color Changing SOL Lighting. Atlantic’s SOL

lighting features solid brass bodies with an oil-rubbed bronze ﬁnish. These LEDs

create a vibrant nightime atmosphere with 48 different colors and 16 different

pre-programed color changing combinations. Multiple LEDs can be connected to

be run through one transformer and be controlled by one remote.

Prior to Operation and Installation

Caution:

• DO NOT operate this product under any condition other than those for which it

is speciﬁed. Failure to observe these precautions can lead to electrical shock,

product failure, or other problems.

• Follow all aspects of electrical codes when installing SOL Lighting.

• To reduce the risk of electrical shock, connect only to a 110 volt receptacle

protected by a ground fault circuit interrupter (GFCI).

• The input power to the Color Changing Control Module is 12 volt AC. The

Control Module can be connected to a larger outdoor lighting transformer;

however this must be done on the 12 volt AC input side of Control Module.

Removing the Control Module or tampering with the cord between the Control

Module and the light ﬁxture will damage the LEDs and void warranty.

• The Control Module is weather resistant with an IP54 rating. Do not submerse

the Control Module or expose it to heavy rainfall. It must be mounted off the

ground close to the power source. Failure to do so will void the warranty.

Installation

Fixture Installation

SOL Color Changing Spotlights offer three different mounting options for your

convenience:

• Adjustable stand: for placement on rock ledges, under waterfalls or for

highlighting streambeds

• Ground stake: for installation around the perimeter of the water feature or

in conventional landscape installations

• Nested: without the stand or stake, amongst the pond stones

SOL Color Changing Light Ring is ideal for illuminating fountains and up lighting

waterfalls.

• Proper light placement is important for every project. Whenever possible lights

should be positioned facing away from the viewing area to minimize hot spots.

2 7

Problem Possible Cause Possible Solution

Remote is not working

(no indicator light)

No batteries / batteries

dead Put in new batteries.

Remote is not working

(indicator light is on)

Remote is not synced with

Control Module

Refer to synchronizing the

remote instructions on page 5.

LED light will

not illuminate

No power to outlet Conﬁrm power to outlet.

No Power to LED Check all connections, ensure

cord is not cut or damaged.

LED is broken / defective Replace LED bulb

LED color differs

from remote control

Improper connection

between LED light and

control module

Inspect connection / align

arrow on plugs

Controller failure Contact Dealer for repair /

replacement

Multiple lights display

different colors when

connected to the

same splitter

Improper connection

between LED light and

3-way splitter

Inspect connection / align

arrow on plugs

Controller failure Contact Dealer for repair /

replacement

Troubleshooting Guide

Always turn off power before inspecting the Color Changing Fountains. Failure to

observe this precaution can result in a serious accident.

Before ordering repairs, carefully read through this instruction booklet. If the

problem persists, contact your dealer.

Preset Light Changing Modes

AOn/Off Button

Touch for one second to turn on or off.

Mode Selection

Touch to switch between Color Wheel and Preset

Light Changing Mode

CColor Wheel

DPreset Light Changing Mode Selection (Forward)

EPreset Light Changing Mode Selection (Backward)

FBrightness / Speed (Up)

GBrightness / Speed (Down)

Indicator Lamp

1Solid Crystal White

2Continuous full spectrum fade change

3Solid Red

4Solid Green

5Solid Blue

6Solid Aqua

7Solid Purple

8Solid Yellow

9Red-Green-Blue jump change

10 7 color jump change

11 Red-Green-Blue dimmer change

12 7 color dimmer change

13 7 color dimmer then

7 color jump change

14 Flashing Red

15 Flashing Green

16 Flashing Blue

17 Flashing Red and Blue

Mode Selection

• To switch to the Color Wheel: hold the B button for three seconds or until the

light changes to Crystal White. Hold down the B button again, and the light will

return to the last color displayed while in the Color Wheel mode. Run your

ﬁnger around the color wheel to select a new color.

• To switch to the Preset Light Changing Modes: hold the B button for three seconds

or until the light changes to Crystal White. Press the D button, and the light will

return to the last preset mode displayed while in the Light Changing Modes. Press

the D and E button to switch between the different preset modes.

Changing the Brightness and Speed

In Modes 1-8 and 14-16, you can use the F and G keys to change the brightness of

the light. In Modes 9-13 and 17, you can use the F and G keys to change the speed

of the light transitions. There are 8 levels for each.

Synchronizing the Remote to the Control Unit

If the remote control stops working properly, please install fresh batteries. If

problems persist, the remote may need to be re-synced to the control module.

Follow the instructions below to re-sync the remote control.

1. Unplug the transformer .

2. Hold the F button down (The red indicator lamp on the remote will be blinking).

3. While still holding the F button down, plug in the transformer. The Colorfalls

will start blinking.

• If the light ring blinks three times and stops, the remote and control unit

are synchronized.

• If the light ring blinks six or more times, it is clearing all codes. Repeat

steps 1-3.

Maintenance

Replacement LED Bulbs are available for SOL Color Changing Spotlights and

Compact Spotlights. To loosen and tighten the brass lens ring on SOL Color

Changing Spotlights and Compact Spotlights, use the included key. Simply place

the key in the slots on the brass lens ring to loosen or tighten. Ensure that all

components are installed correctly after servicing. Inspect the silicone gaskets for

defects and proper placement before re-assembling. Ensure that the lens ring is

tightly secured before submersing the ﬁxture.

Operation

Technical Data (Control Module)

Working Temperature:

0ºF -140ºF (-20°C - 60ºC)

Output: 3 circuits (R/G/B)

Remote Control Functions

Input Power: AC12V

Output Power: DC12V

Output Current: 5A /circuit

Brass Body

Disc Lamp Gasket Lens Slot

Brass Lens Ring

SOLCC2:

Warranty

All SOL Lighting carries a one-year limited warranty. This limited warranty is

extended solely to the original purchaser commencing from the date of the

original purchase receipt and is void if any of the following apply:

• The cord has been cut or altered between the light body and the Control

Module.

• The light body / LED components have been misused or abused.

• The light body / LED components have been disassembled or

modiﬁed other than as described in this manual.

• The Control Module and/or Remote Control have not been adequately

protected from moisture.

Brass Body

Brass Lens Ring

LED Bulb

Gasket Lens Slot

SOLCC6:

• When camouﬂaging the light cord with rocks and gravel, always leave enough

slack in the cord so that the ﬁxture can be raised above water level for servicing.

• Always verify that the lens cover is tightly secured before submersing the ﬁxture.

• Never cut or shorten the light cord between the Control Module and the light

ﬁxture. Altering the Light Cord will damage the LEDs and void warranty.

• 6 wire extension cords (part # SOLCCEXT) are available to add an additional

20’ of cord to any SOL Color Changing Light. Only one cord can be used on

each light. Never connect multiple extension cords together.

SOLCCMX3 Control Module Installation

• The Control Module is weather resistant with an IP54 rating. Do not submerse

it or expose it to heavy rainfall. It must be mounted off the ground close to the

power source. Failure to do so will void the warranty.

• Ensure that all cable connections are secure.

• Install the control box in a well-ventilated area to ensure that the module

operates within its speciﬁed working temperature.

• Verify that the control module input voltage is 12 volt AC. We recommend that

you use the transformer provided with this unit.

• Do not connect the power before the cord connections are ﬁnished.

• Do not cut or alter the cord between the SOL Light and the Control Module.

• The remote control requires three (3) AAA batteries (not included).

Connecting the Lights

Follow the connecting chart below to connect all cables. The SOLCCMX3 Control

Module and 3-way splitter will accept any combination of Color Changing SOL Light

styles. If more lights are required, multiple splitters can be connected together to

create more outlet connections. A larger transformer (80 watts

maximum) is required if additional lights are installed.

SOLCCLR

Control ModuleTransformer 3-way

Splitter SOLCC2

SOLCC6

Autres manuels pour SOLCC2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Atlantic Équipement d'éclairage

Atlantic

Atlantic CCCS2-74096 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur