Atlantic CCCS2-74096 Manuel utilisateur

Product Manual | Manuel du Produit | Manual del Producto

706-865-0220

www.graystonecreations.com

CCCS    CCCS    CCRL  

CCHL    CCHL    CCFL 

CCSL    CCBL   CCSMX  

TRANS    TRANS  

Introduction

Thank you for purchasing Atlantic Color Changing Lighting. Atlantic’s Lighting features solid

brass bodies with an oil-rubbed bronze ﬁnish or high-impact plastic housings. These Lights

create a vibrant nighttime atmosphere with a near unlimited number of colors with the

InﬁColor Smart Module. Multiple ﬁxtures can be connected to a single Smart Module and

controlled via mobile application on your Apple or Android device.

Prior to Operation and Installation

Caution:

• DO NOT operate this product under any conditions other than those for which it is

speciﬁed. Failure to observe these precautions can lead to electrical shock, product failure,

or other problems.

• Follow all electrical codes when installing Atlantic Lighting.

• To reduce the risk of electrical shock, connect transformer to a 120 volt receptacle protected

by a ground fault circuit interrupter (GFCI).

• Quick-connect plugs are gasketed for outdoor use and must be fully tightened to prevent

water inﬁltration. Quick-connect plugs are not waterproof and should not be submersed.

• Always use dielectric grease on all connections and verify that the lens ring is tightly secured

before submersing the ﬁxture.

• Never shorten or cut the cord on Atlantic Color Changing Lights. Removing the driver or

cutting/shortening the cord will damage the LED and void the warranty.

• Extension cords (model #CCEXT20) are available to add an additional 20’ of cord to

any Light.

• The InﬁColor Smart Module is weatherproof, but must be mounted vertically above the

ground on a wall or post within reach of a properly grounded GFCI outlet. Do not submerse

the Control Module or expose it to heavy rainfall. Failure to do so will void the warranty.

• The InﬁColor Smart Module can be connected to an existing 12 volt AC lighting system by

cutting and splicing the ﬂat low voltage wire that supplies power to the Module.

• Adapters are included to adapt newer 5-wire lighting components and InﬁColor Smart

Module to older 6-wire ﬁxtures and control modules. USE ONLY ONE ADAPTER PER ZONE/

SEGMENT. COMBINING ADAPTERS WILL DAMAGE SYSTEM. DO NOT USE MORE THAN

ONE ADAPTER PER ZONE OR SEGMENT.

COMPACT SPOTLIGHTS - CCCS2 / CCCS4

Installation

Compact Spotlights oer three dierent mounting options for your convenience:

• Adjustable stand: for placement on rock ledges, under waterfalls or for

highlighting streambeds

• Ground stake: for installation around the perimeter of the water feature or

in conventional landscape installations

• Nestled: without the stand or stake, amongst the stones and gravel

Proper light placement is important for every project. Whenever possible, lights should be

positioned facing away from the viewing area to minimize glare and hot spots. When

camouﬂaging the light cord with rocks and gravel, always leave enough slack in the cord so

that the ﬁxture can be raised above water level for servicing.

Maintenance

Replacement diode, gasket

and lens kits are available for

Compact Spotlights. Unplug

the ﬁxture. Loosen the brass lens

ring. Remove lens ring, lens and

gasket. Carefully remove the

diode assembly and replace.

Install new silicone gasket and

lens and reassemble. Ensure

that all components are installed

correctly after servicing and the

lens ring is tightly secured before

submersing the ﬁxture.

SPOUT LIGHT - CCSL2

Installation

The Spout Light can be installed in the plumbing behind a wall, shining through a Wall Spout

(see Figure 1) or under a core-drilled stone or pot (see Figure 2). The light is designed to be

installed in any tee that has 1” female threads. If the tee is larger than 1”, a reducing bushing with

1” female threads will be needed. Install the light into the tee, with the light facing the water

outlet. Apply Teﬂon tape, paste or RTV silicone to the threads of the light and thread the light

into the ﬁtting. Do not use the cord to twist in the light or allow it to become twisted when

tightening. The spout light cannot transmit light through sweeps or around corners. There must

be a direct path for the light to be transmitted. The use of rigid PVC plumbing (1” diameter or

greater) is highly recommended for the best results.

Figure 1.

1½” Tee

1½” x 1”

Reducing

bushing

Figure 2.

¾” Kink-Free

tubing

1” Female

threaded Tee

LIGHT RING - CCRL5

Installation

The Ring Light is ideal for illuminating bubbling pots, fountains

and uplighting waterfalls. The brass body accommodates 1⁄”

standpipes. With the bushing installed, the hole in the center of

the light accommodates 1” standpipes. Simply slide the Ring

Light over the standpipe to illuminate the interior of an

overﬂowing vase or fountain. Remove the center bushing to

accommodate 1⁄” standpipes. The Ring Light’s minimal ⁄” proﬁle

makes it ideal for uplighting waterfalls and large trees.

Brass

Body

Diode Gasket Lens Slot

Brass Lens Ring

WWCS2:

Brass Body Diode

Gasket Lens

Brass Lens Ring

WWCS4:

HARDSCAPE LIGHTS - CCHL6 / CCHL12

Installation

Hardscape Lights are designed to be installed into walls and columns, just under capstones.

The diode assembly can be replaced without removing the cord or the capstone. The round

18” long cord between the driver and the luminaire cannot be cut, and some accommodation

must be made for the driver in most applications. We recommend installing a 1” conduit into

the wall to accommodate the cord before installing the ﬁxtures.

When installing the mounting bracket, make sure the stone above the bracket does not rock

or pinch the cord. The holes in the bracket serve as glue points to hold the bracket in place.

NOTE: Hardscape Lights are not submersible.

Maintenance

Replacement diode assemblies are available for

Hardscape Lights. Remove the screws on the

existing light, being careful not to let the diode

assembly fall, as this could break the plug

connecting the light to the cord. Lower the diode

assembly and squeeze the locking clip to separate

the plugs. Plug in the new diode assembly, making

sure the gasket has not moved or shifted and that

the notched edge of the diode assembly ﬁts

between the two ridges on the cord gasket. Align

the screw holes and hand tighten the screws.

Maintenance

Replacement diode, gasket and lens kits are available for Spout Lights. Unplug the ﬁxture. Loosen

the brass lens ring. Remove lens ring, lens and gasket. Carefully remove the diode assembly and

replace. Install new silicone gasket and lens and reassemble. Ensure that all components are

installed correctly after servicing and the lens ring is tightly secured before submersing the ﬁxture.

CCHL6:

CCSL2

Diode

Maintenance

Replacement diode assemblies are available for

Hardscape Lights. Remove the screws on the

existing light, being careful not to let the diode

assembly fall, as this could break the plug

connecting the light to the cord. Lower the diode

assembly and squeeze the locking clip to separate

the plugs. Plug in the new diode assembly, making

sure the gasket has not moved or shifted and that

the notched edge of the diode assembly ﬁts

between the two ridges on the cord gasket. Align

the screw holes and hand tighten the screws.

WIRING KITS - CCSM30X3

All Color Changing LED lights and wiring components

are connected via a quick-connect plug. Color Changing

LED Lights will not operate if plugs are aligned incorrectly. The connectors are keyed to ensure

the connections line up properly. Color Changing quick-connect plugs carry both AC and DC

current to the in-line driver. Moisture entering the connections will allow the AC and DC

current to cross which can damage the lighting system.

Quick-connect plugs are gasketed for outdoor use and must be fully tightened to

prevent water inﬁltration. Quick-connect plugs are not waterproof and should not be

submersed. Dielectric grease is included and should be used in all connections to eliminate

water inﬁltration.

The CCSM30X3 wiring kit enables up to three Color Changing lights (any models) to be

installed together and controlled by a single transformer, Smart Module and App. The

transformer must be plugged into a properly grounded GFCI outlet. Please follow the

connection diagram below for proper installation.

BAR LIGHT - CCBL5

Installation

The Bar Light is a linear light designed to wash

walls, falls and spillways with a wide beam angle.

Solid brass Bar Light includes dual bases for

positioning on any horizontal surface. For other

applications, included stainless steel L-brackets

may be used to mount Light to any hard surface.

Mount the brackets to the light and measure

between the holes, center to center. Detach the

brackets from the light. Mark where the light is

to be mounted and attach the brackets to the

mounting surface using an appropriate fastener.

Mount the light to the brackets. The mounted

Light rotates 30° in either direction for versatility in

directing illumination.

FOUNTAIN LIGHT - CCFL2

Installation

Atlantic’s epoxy encased Fountain Light illuminates water inside

vases, basalts and bubbling boulders. The PVC body with bottom

mounted cord ﬁts inside 1⁄” socket ﬁttings and 2” bore holes.

Glue the ⁄” slip x ⁄” barbed ﬁtting, included, to attach ⁄”

Kink-Free tubing directly to Fountain Light. Without the ﬁtting,

the light mounts directly onto ⁄” rigid Sch40 PVC.

InﬁColor Smart Module

30 Watt

Transformer

LIGHT #1

LIGHT #2

LIGHT #3

Outlet Power

Terminals

INFICOLOR SMART MODULE

Installation

The InﬁColor Smart Module is weatherproof, but must be mounted above the ground on a

wall or post within reach of a properly grounded GFCI outlet. Do not submerse the Control

Module or expose it to heavy rainfall.

• Install the Module in a well-ventilated area to ensure that the module operates within its

speciﬁed working temperature.

• Verify that the Smart Module input voltage is 12 volt AC. We recommend that you use the

transformer provided with this unit.

Operation

The TRANS88 and TRANS150

have a control panel featuring

a rotary timer control switch,

photocell and circuit

breaker/reset button.

The circuit breaker will turn o

power to the lighting system in

case of overload/power surge.

If the circuit is tripped, inspect/repair

the lighting system and depress the reset

button to restore power. The photocell

automatically turns the transformer on when it begins to get dark outside. The photocell does

not need to be in direct sunlight; however it must have access to indirect sunlight to operate

eectively. The timer switch provides several modes of operation. You can choose OFF, ON,

AUTO, 4H, 6H, or 8H.

OFF: Output power is o / system is o

ON: Output power is on / system is on at all times

AUTO: Photo cell will turn the output power on at

dusk and o at dawn

4H: Photo cell will turn the output power on at

dusk and it will turn o after 4 hours

6H: Photo cell will turn the output power on at

dusk and it will turn o after 6 hours

8H: Photo cell will turn the output power on at dusk and it will turn o after 8 hours

Input Power Cord

Timer Control

Photocell Sensor

Circuit Breaker / Reset Button

AUTO

OFF

4H 6H 8H

TRANSFORMERS - TRANS88 / TRANS150

Installation

Strip and connect the wires to the outlet power terminals

on the back of the transformer. Loosen the screws on the

outlet power terminals and slide the wire under the screw plate.

Tighten the screws to secure the wire.

Mount the Transformer in the desired location.

The Transformer is weather-resistant and must

be mounted above the ground on a wall or post.

Ensure that the power cord is within reach of a properly grounded

Ground Fault Circuit Interrupter (GFCI) equipped outlet.

After all connections to low voltage lights have been completed, plug the input power cord

into the 120 volt GFCI outlet to complete installation.

• Use dielectric grease on all connections and ensure that all cable connections are secure.

• Do not connect the power before the cord connections are ﬁnished.

• Do not cut or alter any round cords. Cutting or damaging any round cord will void the warranty.

CONNECTING LIGHTING TO MODULES

All Atlantic Color Changing Lighting is fully forward and backward compatible. Adapters are

included to adapt newer 5-wire lighting components and InﬁColor Smart Module to older

6-wire ﬁxtures and control modules. The adapters included with the InﬁColor Smart Module are

for use with older lighting. The adapters included with new lighting components are for use with

the older Control Module.

CAUTION: COMBINING ADAPTERS WILL DAMAGE SYSTEM. DO NOT USE MORE THAN ONE

ADAPTER PER ZONE OR SEGMENT.

Apply dielectric grease, included with the InﬁColor Smart Module and all new lights, to the

pins of the plugs on the Module and light cords. Line up the keys; the plugs will only ﬁt one

way. Connect the plugs to the adapter and tighten the threaded ring. Complete the tightening

process by wiggling the connection and retightening the threaded ring 2-3 times until

ﬁrmly seated.

HOWTO CALCULATE WATTAGES & MAKE CUSTOM SETUPS

The InﬁColor Smart Module provides 40 watts to each of three zones. The zones may be linked

and synchronized as desired. Add up the wattage of each light, which can be found in the

Catalog, the packaging, the instructions or the website, to ﬁnd the total wattage of the group.

The wattage shown is the highest wattage that the light will draw, rounded up to ensure Smart

Module capacity is never exceeded.

There is also a limit to the length of any lighting run. The number of extension cords you can use

consecutively depends on the total wattage of the zone.

If your total wattage is:

0-10 watts - 4 extension cords max

10-20 watts - 3 extension cords max

20-30 watts - 2 extension cords max

30-40 watts - 1 extension cord max

INFICOLOR MOBILE APP

To connect your mobile device to the Smart Module, be sure the Module is plugged in

and open the InﬁColor App. The app should populate your Smart Module on the opening

screen. Simply select the Module name. Please note the Module can be connected to one

mobile device at a time.

To Conﬁgure Zone Names and Timers

Click dropdown menu. Edit the names of the control module outlets or zones on the “Zone

Settings” page. These zone names will be visible throughout the app. Each zone has an

individual timer function to turn the zone on and o at set times. Click the “Save” button to save

changes. A box will come up conﬁrming the settings have been saved. Click the “Back” button

once conﬁguration is complete.

Color Tab

Use the Color tab to choose colors for the dierent zones using either the color picker or the red,

green and blue sliders at the bottom. Choose the brightness of the color by adjusting the slider.

Select the color for each zone, or select multiple zones to change color at the same time.

Favorites Tab

The Favorites tab stores preset color changing sequences. Select one, two or all three zones.

Choose a sequence of colors, then choose the transition between them, the speed of the

sequence and the brightness. The Edit button deletes stored Favorites you have created.

Custom tab

The Custom tab creates and stores custom color changing sequences. Move the red, green and

blue sliders to choose a color, or select it from the color picker. Once you have decided on the

color, click the “Plus” button to add it to the sequence. Repeat as desired. Add up to 10 colors

to a sequence. Once the sequence has been created it can be named and saved. The saved

sequence will be available on the Favorites page.

Warranty

All Atlantic Color Changing Lighting carries a ﬁve-year limited warranty.

All Color Changing Wiring Components carry a ﬁve-year limited warranty.

Atlantic TRANS88 and TRANS150 carries a one-year limited warranty.

This limited warranty is extended solely to the original purchaser commencing from the date

on the original purchase receipt and is void if any of the following apply:

• Any round cord has been cut or altered.

• The light body/LED components have been misused or abused.

• The light body/LED components have been disassembled or modiﬁed other than as

described in this manual.

• The Smart Module and quick-connect plugs have not been adequately protected from

moisture with dielectric grease.

This warranty excludes labor/cost of labor for removal or installation of any product.

Troubleshooting Guide

Always turn o power before inspecting the Color Changing Lights. Failure to observe this

Problem Possible Cause Possible Solution

Lights will not

turn on

No input power to the

transfomer Verify power to the outlet is on / Check GFCI reset

No outlet power from

the transformer

Check the reset button / circuit breaker on the

transformer

Verify if the transformer is operational by

moving the timer to the ON position

Use a volt meter to verify transformer is

producing 12 volt AC

Photocell malfunction Cover the photocell with a piece of dark tape to

check function

Lights will not

turn o

Timer control Make sure timer control is not set to the ON position

Photo cell is covered Clean sensor and outer clear covering

Make sure nothing is shading the sensor

LED color diers

from app

Improper connection

between LED light and

Smart Module

Inspect connections / realign plugs

Smart Module failure Contact Dealer for repair / replacement

Individual lights

within a larger

system not

working /

displaying

dierent colors

Improper connection

to Splitter / Smart

Module

Verify connections are aligned

Defective 4-outlet

Splitter

Switch positions with a working light on the same

Splitter to identify if the splitter is causing the issue.

Loose connection.

Moisture or corrosion

in connections

Inspect quick-connected plugs for moisture,

corrosion or missing gasket.

Clean/dry/apply dielectric grease and reassemble.

Failed LED diode

assembly

If possible, switch out the diode assembly with

one from a working light of the same model to

determine if the driver has failed.

If driver has failed, replace light.

If test diode works, replacement diode

assemblies are available.

Smart Module is

not responding

to app

App is not synced with

Smart Module Reconnect Smart Module through Bluetooth

Lights

intermittently

responding to app

Loose connection.

Moisture or corrosion

in connections

Inspect quick-connected plugs for moisture

or corrosion.

Clean/dry/apply dielectric grease and reassemble.

Introduction

Merci d’avoir acheté l’Éclairage à Changement de Couleurs Atlantic. L’éclairage d’Atlantic

comprend des corps en laiton massif au ﬁni bronze huilé ou en plastique résistant aux chocs.

Ces luminaires fonctionnent sous l’eau et en plein air pour donner à votre jardin d’eau et à votre

paysage une lueur apaisante et échauante après le coucher du soleil. Plusieurs appareils

peuvent être connectés à un seul InﬁColor Smart Module.

Avant l’opération et l’installation

Mise en garde:

• NE PAS utiliser ce produit dans des conditions autres que celles pour lesquelles il est spéciﬁé.

Le non-respect de ces précautions peut entraîner un choc électrique, une défaillance du

produit ou d’autres problèmes.

• Respectez tous les codes de l’électricité lors de l’installation d’Atlantic Lighting.

• Pour réduire le risque d’électrocution, connectez le transformateur à une prise de 120 volts

protégée par un disjoncteur de fuite à la terre (GFCI).

• Vériﬁez toujours que la bague de l’objectif est bien ﬁxée avant de plonger l’appareil.

• Les luminaires LED se connectent via une ﬁche à connexion rapide, scellée pour une

utilisation en extérieur. Les ﬁches à connexion rapide ne sont pas étanches et ne doivent pas

être submergées.

• Toujours utiliser de la graisse diélectrique sur toutes les connexions.

• L’InﬁColor Smart Module nécessite une source d’alimentation de 12V CA.

• Ne jamais raccourcir ou couper le cordon des Lumieres à Changement de Couleur Atlantic.

Le fait de retirer le driver ou de couper / raccourcir le cordon endommagerait la LED et

d’annuler la garantie.

• Des rallonges (modèle # CCEXT20) sont disponibles pour ajouter 20’/6.1m de cordon

supplémentaires à chaque lampe.

• L’InﬁColor Smart Module est résistant aux intempéries, mais doit être monté vertical

au-dessus du sol sur un mur ou un poteau à la portée d’une prise GFCI correctement mise à

la terre. N’immergez pas le module et ne l’exposez pas à de fortes précipitations. Dans le cas

contraire, la garantie sera annulée.

• L’InﬁColor Smart Module peut être connecté à un système d’éclairage alternatif 12 volts

existant en coupant et épissant le ﬁl plat basse tension alimentant le module.

• Des adaptateurs sont inclus pour adapter l’InﬁColor Smart Module et les nouveaux

composants d’éclairage à 5 ﬁls aux anciens luminaires et modules de commande à 6 ﬁls.

UTILISEZ UNIQUEMENT UN ADAPTATEUR PAR ZONE /SEGMENT. LA COMBINAISON DES

ADAPTATEURS ENDOMMAGERA LE SYSTÈME. NE PAS UTILISER PLUS DE UN ADAPTATEUR

PAR ZONE OU SEGMENT.

LES PROJECTEURS COMPACTS - CCCS2 / CCCS4

Installation

Les Projecteurs Compacts orent trois options de montage pour votre commodité:

• Base réglable: pour le placement sur les saillies rocheuses, sous les cascades ou pour

mettre en évidence les lits de rivière.

• Piquet de terre: à installer autour du périmètre de la pièce d’eau ou dans des installations

paysagères conventionnelles

• Niché: sans le support ou le pieu, parmi les pierres et le gravier

Un bon éclairage est important pour chaque projet. Dans la mesure du possible, les lampes

doivent être orientées à l’opposé de la zone de visualisation aﬁn de minimiser les reﬂets et les

points chauds. Lorsque vous camouﬂez le cordon de lumière avec des cailloux et du gravier,

laissez toujours susamment de mou dans le cordon pour permettre à l’appareil de monter

au-dessus du niveau de l’eau pour le service.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Atlantic Équipement d'éclairage

Atlantic

Atlantic SOLCC2 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur