ATEQ VT36 Manuel utilisateur
VT36 GB VHA1-00-02
Reference Guide
Section A –General Description
Section B –How to use the VT36
VT36 GB VHA1-00-02
General Description of the ATEQ VT36
The principle of this instrument is to awaken and then retrieve data from smart valves mounted
on vehicle wheels, in order to check their identifiers. The instrument interacts with the smart
valves to assist technicians service Tire Pressure Monitor Systems (TPMS). VT36 is capable to
trigger all know sensors.
Front face
Lights
indicators
Keypad
LF Antenna
LCD
display
A
VT36 GB VHA1-00-02
SET
Battery
VT36 Operates with rechargeable battery Type Li-On.
USB connector / Charging the battery
The USB connection allows software updates to be installed onto the
tool using the WEB VT program.
TPM sensor results can also be printed using this program.
The USB connection allows to charge the internal battery.
The symbol is red during the charge.
The symbol becomes green when the charge is complete.
It can be done from a PC (14 hours) or with the wall charger (5 hours).
A
VT36 GB VHA1-00-02
SECTION B –HOW TO USE THE VT36
B.0 SWITCH ON THE VT36
Please, wait until the welcome screen shows “MAIN MENU “.
B
VT36 GB VHA1-00-02
B.1 TESTING A TPM SENSOR
Confirm the choice : VEHICLE SELECTION
Select the brand then confirm
Select 4 or 5 wheels then confirm
VT36 GB VHA1-00-02
Hold the VT36 directly on the rubber
tire, over the valve stem.
Some sensors are banded to the wheel
and can be located 180⁰ opposite the
valve stem. (Refer to owner’s manual)
Start the test cycle
During the trigger processing,
the yellow light is blinking
Low Bat
Pass
Fail
Tx
VT36 GB VHA1-00-02
The tool will vibrate/beep after receiving
the sensor information. The tool will
display the sensor ID, pressure, and
sensor state of the valve that is triggered.
If the tool does not receive the correct
information, the fail LED will illuminate
and you can restart the trigger sequence
by pressing the key again.
Low Bat
Pass
Fail
Tx
Follow the same procedure for the rest of
the three or four wheels by pressing the
key and then key.
(Refer to vehicle owner’s manual or other
reference guides for TPM reset
procedure.)
VT36 GB VHA1-00-02
The picture below is an example of a valve data communication result:
**Note: The VT36 will identify the sensor information that is transmitted. Not
all sensors transmit every piece of information shown. ***
Vehicle make
Pressure
Battery Status
Valve ID
Temperature
VT36 GB VHA1-00-02
B.2 TESTING A KEY (RKE TEST)
Confirm the choice : KEY FOB
Select the brand then confirm
Select radio frequencies then confirm
VT36 GB VHA1-00-02
Start the test cycle
Check the key
Low Bat
Pass
Fail
Tx
Autres manuels pour VT36
1
Table des matières
Autres manuels ATEQ Instrument de mesure
ATEQ
ATEQ VT37 Manuel utilisateur
ATEQ
ATEQ VT31 Manuel utilisateur
ATEQ
ATEQ Huf VT46-HUF Manuel utilisateur
ATEQ
ATEQ D670 Manuel utilisateur
ATEQ
ATEQ D6 Series Manuel utilisateur
ATEQ
ATEQ G520 Manuel utilisateur
ATEQ
ATEQ F6Class Manuel utilisateur
ATEQ
ATEQ D620 Manuel utilisateur
ATEQ
ATEQ VT 56025 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur