AT&T CL2909 Manuel utilisateur

Quick start guide

CL2909 Speakerphone

with caller ID/call

waiting

LOWER

CAUTION: To reduce the risk of fire or injury to persons or damage to

the telephone, read and follow these instructions carefully:

Use only four AA alkaline batteries (not included).

Do not dispose of the battery in a fire. Like other batteries of this type,

it could explode if burned. Check with local codes for special disposal

instructions.

Do not open or mutilate the battery. Released electrolyte is corrosive and

may cause damage to the eyes or skin. It may be toxic if swallowed.

Exercise care in handling batteries in order not to create a short circuit. Do

not allow conductive materials such as rings, bracelets, or keys to touch

the battery. The battery or conductor may overheat and cause harm.

Use the battery identified for use with this product only in accordance with

the instructions and limitations specified in this manual.

Observe proper polarity orientation between the battery and metallic

contacts.

Do not disassemble your telephone. There are no user-serviceable parts

inside. Refer to qualified service personnel for servicing.

STOP!

If you subscribe to high-speed Internet service (digital subscriber line -

DSL) through your telephone line, you must install a DSL filter between

the telephone line cord and the telephone wall jack (see page 3). The filter

prevents noise and caller ID problems caused by DSL interference. Please

contact your DSL service provider for more information about DSL filters.

Your product may be shipped with a protective sticker covering the telephone

base display, remove it before use.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial

1 (866) 288-4268.

Make sure to install four

AA alkaline batteries

(not included).

See page 2 for easy

instructions.

Battery installation

Before using the telephone, you should install four good AA alkaline batteries

(not included) to provide memory backup and enable the use of some

features. The four AA batteries are required for the following features to work:

speakerphone, hold, mute, flash, caller ID features, display, feature options

menu, directory, clock, and the CALL INFO light.

If you unplug the telephone from the wall jack, or you lose telephone service

for over 10 minutes, and good batteries are not installed, the following

information is lost: call list, numbers stored in the directory, redial list, and

all settings in the feature menu. We recommend that you initially install new

batteries and change the batteries soon after the low battery icon appears.

CAUTION: Always unplug the telephone line cord before installing new

batteries.

Press down on the battery compartment cover tabs as shown and pull to

open the battery compartment cover.

Insert four AA alkaline batteries (not included) following the polarity

markings in the battery compartment.

Close the battery compartment cover as shown, making sure the cover

snaps into place.

Tabletop installation

For wall installation, see pages 7-8 of user’s manual.

Tabletop installation

If you subscribe to high-speed Internet service (digital subscriber line - DSL)

through your telephone line, you must install a DSL filter (not included)

between the telephone base and the telephone wall jack. The filter prevents

noise and caller ID problems caused by DSL interference. Please contact your

DSL service provider for more information about DSL filters.

Follow instructions below to install your telephone to tabletop position.

Check the mounting bracket.

The telephone arrived with the mounting bracket positioned for tabletop use.

Make sure it is secure by pressing the two feet.

Connect one end of the long telephone line cord to the jack labeled TEL

on the back of the telephone.

Connect the other end of the line cord to a wall jack.3.

DATA

TEL

Telephone

line cord

Telephone

wall jack

DSL filter (not

included)

Connect the handset to the telephone.

Plug the coiled handset cord into the handset jack on the left side of the

telephone base. Plug the other end of the coiled cord into the handset, then

hang up.

Check for dial tone.

Lift the handset and listen for a dial tone. If you cannot hear a dial tone,

press VOLUME . If you still do not hear a dial tone, see the Troubleshooting

section on pages 30-31 of user’s manual.

Your telephone will work immediately after installation using the default

feature settings (see default settings of the Feature summary on page 14 in

the user’s manual).

NOTE: If you subscribe to caller ID services from your local telephone

service provider, you must follow the instructions in Set home area code (see

page 11 of user’s manual), for your phone to properly recognize and dial calls

from the call history list. You may also need to check Set local area code

(see page 12 of user’s manual) if you want the telephone to recognize

multiple area codes.

LOWER

Quick reference guide

PROG

Press to program numbers

stored in one-touch locations.

REDIAL

Press to redial the last number

dialed.

FLASH

During a call, press to receive

an incoming call if you

subscribe to the call waiting

service from your local

telephone company.

HOLD

Press to place a call on hold.

MUTE

Press to mute the handset or

speakerphone microphone;

press again to resume

conversation.

Dial pad keys

With the handset lifted, press

to dial a number. With the

handset on the base, press

to search the directory by

name.

RINGER

Slide the ringer switch

on the right side of the

telephone base to adjust

ringer volume.

SPEAKER

Press to turn the base

speakerphone on or off.

VOLUME

Press to adjust the

speakerphone or handset

listening volume.

LOWER

One-touch keys

Press to display the numbers

stored in one-touch locations.

CALL LIST

Press to review call history

records or scroll through

options when in the feature

menu.

CLEAR

Press to return to idle mode.

DISPLAY DIAL

Press to dial the displayed

number.

LOWER

Press to enter lower locations

of one-touch keys.

REMOVE

Press to delete the displayed

entry.

When the telephone is idle,

press and hold to remove all

call history entries.

OPTIONS

Press to display the menu.

When in the menu, press to

save your setting and advance

to the next feature setting.

Manuels Téléphone populaires d'autres marques

GE 2-9480 Manuel utilisateur

Geemarc

Geemarc PHOTOPHONE 155 Manuel utilisateur

D-Link

D-Link DWR-720/PW Manuel utilisateur

Interquartz

Interquartz Gemini IQ333 Manuel utilisateur

SSS Siedle

SSS Siedle HT 840-0 Manuel utilisateur

Motorola

Motorola TITANIUM Manuel utilisateur

Panasonic

Panasonic ICX Manuel utilisateur

LG H870DS Manuel utilisateur

Samsung

Samsung GT-I9500 Manuel utilisateur

Selta

Selta zenyth 600 Manuel utilisateur

Doro

Doro AFTI 20 Manuel utilisateur

UNIQCELL

UNIQCELL A1 Manuel utilisateur

Panasonic

Panasonic KX Series Manuel utilisateur

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Manuel utilisateur

BT Decor 425 Manuel utilisateur

NEC

NEC SV8500 Manuel utilisateur

Teledex

Teledex PEARL Manuel utilisateur

Ericsson

Ericsson Dialog 3213 Manuel utilisateur