AT&T Merlin 1030 Manuel utilisateur

AT&T

MERLIN

™

COMMUNICATIONS SYSTEM

INSTALLATION GUIDE:

MODELS 1030 AND 3070

Table of Contents

Page

Introduction

Getting Started

Preparing the Network Interface

Extend the Network Interface to the Jack Field

Installing the Control Unit

Position the Control Unit

Attach the Model 1030 Expansion Unit to the Control Unit

Insert the Modules

Set the Control Unit Switches

Connect the Control Unit to the AC Outlet

Test the Outside Lines

Attach Cord Clips to the Control Unit

Connect the Control Unit to the Outside Lines

Connect the Modular Jumper Cords to the Control Unit

Connecting Voice Terminals

Assemble the Voice Terminals

Connect Each Voice Terminal to the System

Test Each Voice Terminal for a Dial Tone

Label Voice Terminals with Intercom Numbers

Installing Accessories

Feature Accessories

Power Accessories

System Tests

Test the Jacks in the Voice Terminal Modules for a Dial Tone

Place an Outside Call

Place an Intercom Call to a Voice Terminal

Test Each Line Number

What’s Next?

System Changes

Adding an Outside Line

Adding a Voice Terminal

Moving a Voice Terminal

Changing Touch-Tone/Rotary Service

Troubleshooting

Troubleshooting Table

General Test

Appendix A: Interference Information

Appendix B: FCC Registration and Repair Information

Index

Introduction

This installation guide tells you how to install and test your

MERLIN™

com-

munications system, Model 1030 or Model 3070. It leads you step by step

through system installation, from a pre-installation checklist to system tests.

You should perform the steps in the order in which they are presented because

many of the earlier steps prepare the system for later steps.

When you complete the steps in this guide, refer to the Administration

Manual: Models 1030 and 3070 (packed with your Feature Module) for program-

ming and administration instructions. Your system may not be fully operable until

you have programmed and administered it.

This guide consists of the following sections:

●

Getting Started

reviews preparation for system installation and includes

a diagram of a simple

MERLIN

system configuration, identifying com-

ponents and showing them in relation to one another.

Preparing the Network Interface

tells you how to prepare the connec-

tion to your outside telephone lines.

Installing the Control Unit

tells you how to set up and connect the con-

trol unit.

Connecting Voice Terminals

explains how to connect the voice terminals

(telephones) to the system.

Installing Accessories

suggests some accessories you may want to con-

sider adding to your system and when you should consider installing them.

System Tests

provides tests to help you determine if your system is prop-

erly installed.

What’s Next? refers you to documents that contain instructions for

customizing your system to meet your particular business needs.

●

System Changes

describes how to rearrange or alter your system once

it is in place.

●

Troubleshooting

isolates and identifies specific system problems that

could arise during system installation, and suggests solutions to basic

problems.

TIP:

The steps in this guide are numbered in order of performance. To visualize

a step as it is described, refer to the pictures accompanying the text. The

numbers in the pictures correspond to the step numbers in the text.

Getting Started

This guide assumes the tasks on the following list have been completed. Review

the list carefully before proceeding with system installation. If you have not com-

pleted the tasks on this list, do so now.

●

Check the items in your shipment against your copy of the order form.

Make sure the items and quantities agree. Be sure to keep the instructions

that come with each component, and also keep the packing boxes so you

can easily return equipment under warranty if necessary.

●

Get acquainted with the system environment.

Review the planning sheets you drew up when you ordered the system.

Confirm the voice terminal locations, and make sure the control unit loca-

tion meets the following environmental standards:

—

Operating temperatures: 40 to 104°F (4 to 40°C).

—Humidity: not to exceed 80%.

—

Ventilation:Leave 6 inches of space above and to the sides of the

control unit to prevent overheating. Keep the control unit away from

sources of extreme heat (furnaces, heaters, attics, or direct sunlight).

Do not stack multiple control units in rooms that are not air-

conditioned; install them side by side at least 6 inches apart.

—

Airborne contamination: Do not expose the control unit to moisture,

corrosive gases, dust, chemicals, or similar substances.

If the control unit location does not meet these standards, your warranty

may become void.

●

Become familiar with the

MERLIN

system.

Review the drawing of a simple

MERLIN

system configuration, opposite

page, and note how components are related to one another.

NOTE:

The

control unit

and the

modules

it contains provide the power

and the intelligence for all voice terminals and accessories.

expansion unit

increases your system’s capacity from 10 out-

side lines and 30 voice terminals to 30 outside lines and 70 voice

terminals.

Modular jumper cords

connect the jacks on the Voice Terminal

Modules in the control unit to jacks in the jack field.

The jacks in the

jack field

serve as an interface between the con-

trol unit and the building wiring. In some configurations, additional

jacks in the jack field connect the system to its outside telephone

lines.

Building wiring

ties the whole system together, connecting the

voice terminal locations to the jack field at the control unit location.

Modular jacks

terminate the building wiring at the voice terminal

locations.

Modular voice terminal cords

connect the voice terminals to the

modular jacks.

Voice terminals

provide telephone functions and access to the

advanced features in the control unit.

The

ac outlet

is the electrical power source for the control unit.

The

network interface jacks

provide connections to the local

telephone company lines.

Line cords

connect the control unit to jacks at the network inter-

face (or, if necessary, to jacks in the jack field).

Modular jumper cords are identical to modular voice terminal

cords. They have different names in this guide to reflect their different func-

tions and locations in the system.

Voice terminal

Jack field

Modular voice

terminal cord

Modular jack

Modular jumper cord

Building wiring

Expansion unit

Control unit

Line cord

Network interface

AC outlet

●

Make sure your system wiring is in place.

The drawing, right, illustrates the wiring that must be in place before you

begin installing your system. You must have building wiring that runs from

the control unit location to the voice terminal locations. Wiring runs should

end in modular jacks at the telephone locations and in a group of jacks

mounted in apparatus boxes (the “jack field”) at the control unit location.

Each apparatus box should have a white label with blue numbers indi-

cating the numbers of the jacks in the box (1-6, 7-12, etc.). Inside the right

door (the door with the handle) of each apparatus box you should find a

white label lettered in blue to indicate the endpoint location (for example,

“workshop” or “Room 23”) of each jack in the jack field.

You may have your building wiring and jack field professionally installed

or you may install them yourself. If you choose to install your own building

wiring and jack field, follow the Wiring Installation Instructions included with

the Wiring Installation Kit.

You must also have a network interface that links your system with the local

telephone lines. A telephone company representative should have

installed the necessary outside telephone lines and labeled the network

interface to indicate the telephone number for each outside line. Depend-

ing on the type of interface provided by the telephone company, you may

have to run additional wiring from the network interface to the jack field

during installation in order to connect your system to your outside

telephone lines.

If you have your building wiring and jack field professionally installed, you

may want to have the wiring from the network interface to the jack field

installed at the same time (if it’s necessary). But if you prefer to install the

wiring from the network interface to the jack field yourself, this guide tells

you how to do so in the next section, “Preparing the Network Interface,”

page 5.

NOTE: The manufacturers, distributors, and their agents will not be

responsible for damage due to improperly installed wiring.

The FCC requires you to notify your local telephone company of the follow-

ing before permanently connecting your system to their lines:

—

System registration number

For systems with Feature Module 1, 2, or 4:

AS 593M-64884-MF-E

For systems with Feature Module 3: AS 593M-13529-KF-E

—

System ringer equivalence number: 0.8A

—Telephone numbers of the lines to which you are connecting your

system

Jumper cords

Jack field

AC outlet

Network

interface Modular jack

Building wiring

●

—

Preparing the Network Interface

The telephone company should have installed a network interface with 1-line

ings, below, show the three types of interfaces. The table, below, tells you what

jacks (RJ11-type), 2-line jacks (RJ14-type), or multiline connectors (RJ21-type)

to do next depending on the type of network interface you have.

for connecting your

MERLIN

system to your outside telephone lines. The draw-

Mutiline connector (RJ21-type)

2-Line adapter

1-Line jack (RJ11-type) 2-Line jack (RJ14-type)

If the Network Interface

and

has a 1-line jack (RJ11-type) for each outside line

each jack is labeled with its telephone number

each jack is not labeled with its telephone number

has 2-line jacks (RJ14-type) for the outside lines each jack is labeled with the telephone numbers

for its two outside lines

each jack is not labeled with the telephone

numbers for its two outside lines

has one or more 50-pin connectors (RJ21-type) the interface is labeled with the telephone numbers

carrying the outside lines for the outside lines

the interface is not labeled with telephone numbers

for the outside lines

Do This

Go on to the next section, “Installing the Control Unit,”

page 10.

1. Label each jack with its telephone number from the

list provided by the local telephone company.

Go on to the next section, “Installing the Control

Unit,” page 10.

Plug a 2-line adapter (267C) into each jack.

Go on to the next section, “Installing the Control

Unit,” page 10.

1. Label each jack with the two telephone numbers for

its two outside lines from the list provided by the

local telephone company.

Plug a 2-line adapter (267C) into each jack.

Go on to the next section, “Installing the Control

Unit,” page 10.

Go to the instructions for extending the network inter-

face to the jack field, following this table.

1. Label the interface with the telephone numbers for

the outside lines from the list provided by the local

telephone company.

Go to the instructions for extending the network

interface to the jack field, following this table.

●

EXTEND THE NETWORK INTERFACE TO THE JACK FIELD

You need the following to extend the network interface to the jack field:

4-Line adapters

Apparatus boxes

Green-on-white line labels and directories

Single-ended 25-pair connectorized cables

The drawings, right, show a 4-line adapter, an apparatus box, and a 25-pair con-

nectorized cable. You also need a jacket-stripping tool to slit the jacket on the

25-pair cable and a cable termination tool to punch down the wires onto the

blocks on the 4-line adapters. Your equipment supplier or technical consultant

can help you obtain these items.

The table, below, tells you how many adapters, apparatus boxes, and cables

you need based on the number of outside lines you have.

4-Line adapter

Outside Lines

Adapters

Boxes

Cables

1-4

111

5-8

9-12 32

13-16

17-20 53

21-24

25-28

7 4

29-30

Telephone company installers do not normally connect more than 24 out-

side lines to one 50-pin connector. But if you have exactly 25 outside lines, the

phone company may connect all 25 lines to a single 50-pin connector. If you

have exactly 25 outside lines and you find a single 50-pin connector at the net-

work interface, you need only one 25-pair connectorized cable to extend the

network interface to the jack field.

25-Pair connectorized cable

Apparatus box

Add Jacks to the Jack Field

Use the table, page 6, to determine the number of adapters and ap-

paratus boxes you need.

Position each apparatus box so that the door with the handle is on the

right.

Snap adapters into boxes, as needed, so that the jacks on the adapters

face to the right.

Attach the apparatus boxes to each other by meshing the tongues and

grooves as shown.

NOTE:

If you need two apparatus boxes, attach the second to the bot-

tom of the first. If you need a third box, attach it to the right of the first.

If you need a fourth box, attach it to fill in the square, making two col-

umns of boxes with two boxes in each column.

Attach this configuration of apparatus boxes to the leftmost box or boxes

already mounted in the jack field.

Connect the Outside Lines to the Jack Field

Plug the connector on the 25-pair cable into the 50-pin connector at the

network interface.

With a jacket-stripping tool, slit the jacket at the other end of the 25-pair

cable, and cut away as much of the jacket as necessary to allow each

of the individual twisted pairs of color-coded wires to reach the jacks

in the jack field. 1

Following the order and color code in the drawing, below, place the wires

in the terminal block grooves on the adapters.

Punch the wires down with a cable termination tool.

If your cable termination tool does not trim the wires as it punches them

down, trim the ends of the wires protruding from the grooves with a pair

of scissors.

APPARATUS BOX NO.1 APPARATUS BOX NO.2 APPARATUS BOX NO.3 APPARATUS BOX NO.4

BK = black

BL = blue

BR = brown

G = green

O = orange

R = red

S = silver

V = violet

W = white

Y = yellow

Autres manuels pour Merlin 1030

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AT&T Système de conférence

AT&T

AT&T MERLIN LEGEND Calling Group Manuel utilisateur

AT&T

AT&T Merlin 3070 Mode d’emploi

AT&T

AT&T Bell System 7A Manuel utilisateur

AT&T

AT&T MERLIN LEGEND Release 2.0 MLX Queued Call... Manuel utilisateur

AT&T

AT&T MERLIN LEGEND MLX-10 Non-Display Telephone Manuel utilisateur

AT&T

AT&T MERLIN Plus Guide de l'utilisateur

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Manuel utilisateur

AT&T

AT&T MERLIN Plus Guide de l'utilisateur

AT&T

AT&T SPIRIT 308 Mode d’emploi

AT&T

AT&T MERLIN Plus Guide de l'utilisateur

AT&T

AT&T MERLIN 410 Mode d’emploi

AT&T

AT&T MERLIN LEGEND Communications System Key System Planning Forms... Manuel technique

AT&T

AT&T Merlin 3070 Mode d’emploi

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Guide de l'utilisateur

AT&T

AT&T Merlin 3070 Manuel utilisateur

AT&T

AT&T MERLIN LEGEND Release 2.0 MLX Queued Call... Manuel

AT&T

AT&T PARTNER Guide de démarrage rapide

AT&T

AT&T Merlin Legend 10BS Manuel utilisateur

AT&T

AT&T Merlin 1030 Manuel utilisateur

AT&T

AT&T Merlin 1030 Manuel utilisateur

AT&T

AT&T MERLIN Plus Release 1 Manuel utilisateur

AT&T

AT&T Partner Series Guide de démarrage rapide

AT&T

AT&T MERLIN LEGEND Manuel de service

AT&T

AT&T Merlin 3070 Mode d’emploi

Manuels Système de conférence populaires d'autres marques

Kramer

Kramer VIA GO Manuel utilisateur

AVT

AVT MAGIC AC1 Go Manuel utilisateur

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuel utilisateur

Sony

Sony PCS-I150 Manuel utilisateur

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuel utilisateur

Prentke Romich Company

Prentke Romich Company Vanguard Plus Mode d’emploi

Speakerbus

Speakerbus iD 712 Manuel utilisateur

Trelleborg

Trelleborg SafePilot CAT PRO Manuel utilisateur

Sennheiser

Sennheiser ADN Manuel utilisateur

ADTRAN

ADTRAN NetVanta 7100 Manuel utilisateur

AINA

AINA PTT Voice Responder Manuel utilisateur

Yamaha

Yamaha ProjectPhone PJP-100H Manuel utilisateur

vissonic

vissonic VLI Series Manuel utilisateur

Panasonic

Panasonic KX-VC500 Manuel utilisateur

Poly

Poly Trio 8300 Manuel utilisateur

Crestron

Crestron Mercury CCS-UCA-SMK Dessin dimensionnel

Inmarsat

Inmarsat mini M Manuel utilisateur

Tenveo

Tenveo ALL-IN-ONE Manuel utilisateur