ATAGO RX-5000i Manuel

Installation Qualification

(IQ)

RX-5000i

Automatic Digital Refractometer

Installation Qualification Procedure

IQ Procedure

Install the instrument, following this procedure, and fill out the Installation Report found on

the following page.

1. Unpacking

1) Unpack the RX-5000i and place it on a level surface, such as a desk. Remove the

packaging materials from the instrument and included accessories. Check the

appearance of the RX-5000i for scratches and blemishes.

2) Refer to the list of included accessories in the instruction manual to confirm that the

instrument has arrived complete with all accessories.

2. Choosing a Location

Place the instrument in an environment that meets the following criteria.

1) A level surface with no vibration

2) Away from direct sun light and heat sources

3) Free of dust and corrosive fumes

4) An ambient temperature within the range of 15.00 to 30.00℃

5) Within 2 meters from an electrical outlet

6) Provides sufficient room for operation

3. Confirming the Model Name and Serial Number

1) A label indicating the model name and serial number is found on the right rear side

of the instrument.

2) Check the model name and serial number on the label against the model name and

serial number listed on the inspection report as well as on the registration card.

4. External Devices

The DP-63 Digital Printer (sold separately) may be connected to the RX-5000i.

1) Unpack the printer and check that it has arrived complete with all accessories.

2) Place the printer next to the RX-5000i and connect them with the signal cable.

3) Referring to the instruction manual, connect the AC adaptor for the printer and

insert the printer paper.

5. Powering On

After the RX-5000i (and printer if using) have been set up, connect the AC power cable

to the socket. Follow the procedure in the Installation Report under “Turning on Power”

to test the operation.

1/2

E-IQ1011-3276-J01

Installation Qualification

(IQ)

RX-5000i

Automatic Digital Refractometer

Installation Report

Item Result

Unpacking

1. Scratches on the body

□No

□Yes

2. Scratches on the prism □No □Yes

3. Included accessories □Complete □Incomplete

Missing accessories:

Choosing a

location

1. Environmental conditions

□Level surface □No direct sun light □No heat source nearby

□Dust-free □Fume-free

□Temperature within the 15 to 30℃range

2. Sufficient space □Yes □No

3. Power supply □Electrical outlet within 2 m

4. Location name

Confirming the

model name and

serial number

1. Model name

2. Serial number

External devices

Using printer?

□Yes

□No

□Connection successful □Designated printer (DP-63)

Powering on

1. Turn the power on to the refractometer and printer.

2. Display the home screen. Touch “MEASUREMENT”

to display the

measurement screen. Make sure that MODE-

1 is selected, and that

the target temperature is set to 20.00℃.

3. Zero-set and measure distilled water.

i. Apply distilled water on the prism.

ii. Touch “ZERO.” (WAITING > READING > ZERO SET END)

iii. Touch “START.”(WAITING > READING > 0.00)

iv. Wipe the water off the prism with tissue paper.

4. Turn the power off of the refractometer and printer.

Operation

Manager

Name :

Operator’s signature :

Test date :

Approver’s signature :

Date :

2/2

E-IQ0704-3261-J01

Autres manuels pour RX-5000i

Autres manuels ATAGO Instrument de mesure

ATAGO

ATAGO PAL-46S Manuel utilisateur

ATAGO

ATAGO PAL-98S Manuel utilisateur

ATAGO

ATAGO PAL-24S Manuel utilisateur

ATAGO

ATAGO PAL-121S Manuel utilisateur

ATAGO

ATAGO PAL-HIKARi 2 Manuel utilisateur

ATAGO

ATAGO DR-M2 Manuel

ATAGO

ATAGO 4555 Manuel utilisateur

ATAGO

ATAGO PAL-66S Manuel utilisateur

ATAGO

ATAGO PAL-26S Manuel utilisateur

ATAGO

ATAGO WM-7 Manuel utilisateur

ATAGO

ATAGO PAL-0 Manuel utilisateur

ATAGO

ATAGO PAL-Easy ACID11 Manuel utilisateur

ATAGO

ATAGO AP-300 Manuel utilisateur

ATAGO

ATAGO PAL-HIKARi 3 MINi Manuel utilisateur

ATAGO

ATAGO PAL-03S Manuel utilisateur

ATAGO

ATAGO PAL-pH Manuel utilisateur

ATAGO

ATAGO PAL-HIKARi 15 Manuel utilisateur

ATAGO

ATAGO PAL-86S Manuel utilisateur

ATAGO

ATAGO DPH-2 Manuel utilisateur

ATAGO

ATAGO PAL-15S Manuel utilisateur

ATAGO

ATAGO PAL-Easy ACID101 Manuel utilisateur

ATAGO

ATAGO PAL-14S Manuel utilisateur

ATAGO

ATAGO PAL-102S Manuel utilisateur

ATAGO

ATAGO PAL-HIKARi 5 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur