Atag A200SOV Manuel utilisateur

User manual

8G.52.70.00/12.10 Changes reserved.

A200SOV

Open vent heat only boiler

ATAG A-Serie

Content

1. Introduction .................................................... 3

2. Safety ............................................................ 5

3. Boiler description ........................................... 6

4. Display and function keys .............................. 7

4.1 The Reset key ......................................... 7

4.2 Setting the heating water temperature .... 8

4.3 Requesting current data .......................... 8

5. Filling the heating system .............................. 9

6. Decommissioning the boiler .......................... 9

7. Error codes .................................................. 10

8. Maintenance ................................................ 10

9. Warranty ...................................................... 10

Important!

It is in your own interest that we should know that you have an ATAG

boiler. Please ll out the warranty card completely and send it back to

us. Then we can be fully at your service.

ATAG A-Serie

These operating instructions describe the func-

tioning and the operating of the ATAG A boilers.

This manual is for the end user. For installation

and servicing there is an installation & servicing

instructions manual for the installer.

Read this manual fully before operating the boiler.

In case of doubt or errors contact your installer.

ATAG Heating reserves the right to change the

specications and dimensions without prior notice.

Work on the boiler must be carried out by a com-

petent person, (Ref: Gas Safe Register) using

correctly calibrated instruments with current test

certication.

When replacing parts use only ATAG Service parts.

Contact details for ATAG Heating UK Ltd can be

found on the back page of this manual.

1 Introduction

ATAG A-Serie

The Benchmark Scheme

ATAG Heating UK Ltd is a licensed member of

the Benchmark Scheme which aims to improve

the standards of installation and commissioning

of domestic heating and hot water systems in the

UK and to encourage regular servicing to optimise

safety, efciency and performance.

Benchmark is managed and promoted by the

Heating and Hotwater Industry Council. For more

information visit www.centralheating.co.uk

Please ensure that the installer has fully comple-

ted the Benchmark Checklist on the inside back

pages of the installation instructions supplied with

the product and that you have signed it to say that

you have received a full and clear explanation of

its operation. The installer is legally required to

complete a commissioning checklist as a means

of complying with the appropriate Building Regu-

lations (England and Wales).

All installations must be notied to Local Area

Building Control either directly or through a Com-

petent Persons Scheme. A Building Regulations

Compliance Certicate will then be issued to the

customer who should, on receipt, write the Noti-

cation Number on the Benchmark Checklist.

This product should be serviced regularly to opti-

mise its safety, efciency and performance. The

service engineer should complete the relevant

Service Record on the Benchmark Checklist after

each service.

The Benchmark Checklist may be required in the

event of any warranty work and as supporting

documentation relating to home improvements

in the optional documents section of the Home

Information Pack.“

ATAG A-Serie

Work on the installation should only be carried out

by qualied personnel with calibrated equipment.

When replacing parts, only ATAG Service

components may be used.

If you smell gas:

- No naked ames! No smoking!

- Do not switch lights on or off or use other

electrical switches.

- Do not use the phone

- Close the gas mains

- Open windows and doors

- Warn the occupants and leave the building

- Only call the gas company or installer once you

are outside the building.

Corrosion protection

Do not use sprays, chlorine-containing cleaning

products, solvents, paints etc. in the vicinity of the

device or its air supply. These substances have

an adverse impact on the device and can lead to

corrosion that may result in failures.

Checking the heating water

Always use potable water for lling the installation.

Adding chemical agents such as frost and

corrosion inhibitors are only to be added by your

installer.

If in doubt, check with your installer or ATAG

Heating UK Ltd.

2 Safety

ATAG A-Serie

The ATAG A is a closed, condensing and

modulating heating boiler which meets the

European standard (CE).

A declaration of conformity can be obtained from

the manufacturer.

The efficiency of the boiler is very high and

the radiation convection and standby losses

very low. The emission of noxious substances

is far below the fixed standards so the boiler is

SEDBUK Class A rated.

3 Boiler description

Example SEDBUK ClassA

ATAG A-Serie

The boiler is equipped with a door at the front. After

opening the door you will nd a brief overview of

the meaning of all the keys and icons. These are

described below.

4 Display and function keys

4.1 Reset-key

The reset key restarts the boiler after a malfunction

has occurred.

In case of a failure the symbol is displayed

with a Cx xx code.

In other cases the Reset button has no function

and will not respond when operated.

See also chapter 7 'Errors'.

°C

(OK )

( ESC)

Boiler operational

Error indication

Request for heating

Service mode or Blocking

Indicator for heating

Information key

Setting of boiler temperature

Reset key

n.a.

ATAG A-Serie

Press + or - ;

The display will show the set value while ashing;

Press + or – to change the set value.

Each change becomes active directly.

Heating program OFF:

Press – until the lowest value is reached and then

press – again.

The display is showing -- and the upper is off.

Switching on works in reverse order.

Briey press the i-button or scroll button to obtain

the following values:

A0 = Supply water temperature

A1 = Return water temperature

A2 = Hot water temperature (n.a.)

A4 = Flue gas temperature

(Only if a ue gas sensor is connected)

A5 = Outside temperature (n.a.)

A6 = Water pressure

A9 = Rpms of fan

To return to the standard view press ESC.

4.2 Setting the heating water temperature

4.3 Requesting current data

ATAG A-Serie

5 Filling the heating system

This boiler is part of an 'Open Vent' heating

system. The system is not pressurized, but is

lled automatically by a lling system in the loft.

If there is a problem with this system, please

contact your installer.

When the heating system is lled and after a

power interruption the boiler will be reset and starts

with a venting program. After the venting program

(display shows c1 05) of approx. 7 minutes has

ended, the boiler will be operational again.

In case of, for instance, a holiday:

Heating OFF:

Press the - key of the key until the lowest

value has been reached. Release the key and

press the – key once again. The display is showing

--. The program has thus disabled. The arrow to

the left is off.

In case of work on the heating installation:

Make sure no heat request occurs: set the room

thermostat to low. Pull the plug from the wall

socket. If the installation is being drained, you

have to take into account that part of the heating

water will remain in the boiler. Make sure that the

remaining heating water in the boiler cannot freeze

in case of frost.

6 Decommissioning the boiler

ATAG A-Serie

In the event of a failure (this is indicated by a c

and number code on the display) you can try to

eliminate the failure by pressing the Reset key. If

the failure persists, please contact your installer

as soon as possible and tell him the number code.

There are also messages with a c and a number

code that constitute no failures. These messages

will cancel themselves over time. Operating the

reset button has no effect then, for example:

c1 05 venting program active (approx. 7 min.)

If leaks occur in the installation, please contact

your installer.

Venting program active

Conclude a maintenance agreement with your

installer in order to have the installation periodically

checked and adjusted.

The cover of the boiler consists of plastic parts,

which can be cleaned with a normal (non-

aggressive) cleansing agent.

For the warranty conditions, see the Warranty

Card that has been delivered with the boiler.

7 Errors

8 Maintenance

9 Warranty

Autres manuels pour A200SOV

Table des matières

Autres manuels Atag Chaudière

Atag

Atag Q-Solar Manuel utilisateur

Atag

Atag XL75F Note de version

Atag

Atag Premier E-SHR 15 Guide de l'utilisateur

Atag

Atag 41-310-12 Manuel utilisateur

Atag

Atag A200S Note de version

Atag

Atag IC series Manuel utilisateur

Atag

Atag XL75W Note de version

Atag

Atag IS 12 Note de version

Atag

Atag iC Economiser 27 Guide de démarrage rapide

Atag

Atag Blauwe Engel S-HR Manuel utilisateur

Atag

Atag iR 15 Note de version

Atag

Atag A325EC Manuel utilisateur

Atag

Atag QR Series Manuel utilisateur

Atag

Atag iSteel Series Manuel utilisateur

Atag

Atag i28C Note de version

Atag

Atag Blauwe Engel S-HR Series Guide de l'utilisateur

Atag

Atag E 22S Guide de l'utilisateur

Atag

Atag XL-F Series Manuel utilisateur

Atag

Atag A-Series Manuel utilisateur

Atag

Atag Q 25S Note de version

Atag

Atag Q 25S Manuel utilisateur

Atag

Atag Q 25S Note de version

Atag

Atag iR 12 Note de version

Atag

Atag Q 51C Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur