AstroJet 1000P Manuel utilisateur
Page 1
Step 1
Unpack Printer and Accessories
Place Printer on a stable surface.
Attach Side Media Guides [1], Rear Media Guide and
Support [2] and Top Cover with included hardware.
Save packaging materials.
Step 2
Install 5 Inkjet Cartridges
1. Remove inkjet
cartridge from
packaging.
DO NOT touch copper
contacts, metal plate,
or gold printhead.
Remove protective
tape from printhead.
2. Open latch levers on
inkjet cartridge holders.
3. With cartridge
printhead pointing
down, slide cartridge
into holder, push down
and toward contacts in
holder.
4. Make sure cartridge is
seated in holder. Close
latch lever to secure
cartridge in holder.
DO NOT force lever
into place.
5. Repeat Steps 1-4 for remaining cartridges.
Ink in cartridge may be harmful if
swallowed. Keep new and used
cartridges out of reach of
children. Discard empty
cartridges immediately.
AstroJet 1000P
Quick Start Guide
Page 2
Step 3
Connect Power to Printer
1. Main power switch [1] is OFF. Connect one end
of power cord to printer receptacle [2].
2. Plug other end into a 115-220 Volt AC, 50/60
Hz. grounded outlet.
DO NOT TURN POWER SWITCH ON YET
Step 4
Connect Printer to Computer
Printer has both USB and Parallel Ports.
(Located on Side Cover as shown.)
USB Cable Users: Plug USB cable from computer into
Printer’s USB port [1].
Parallel Cable Users: Plug Parallel Printer Cable from
computer into Printer’s Parallel Port [2]. Latch two
locking clips.
Step 5
Install the Print Driver
Load “Printer Drivers”
CD into computer's
CD/DVD drive.
If “Drive Installation CD”
launch window appears,
you can ignore it.
DO NOT TURN PRINTER POWER ON YET
1. With Printer connected to computer via USB or
parallel port, turn Printer ON. In a few minutes
“Welcome to the Add Printer Wizard” screen
opens. Click Next>.
2. “User Information”screen. Type in your
company and name. Click Next>.
Page 3
3. Select your Printer Model from list displayed.
Click Next>.
4. “Select the Printer Port”screen. Select LPT1
for parallel cable connection or USB for USB
connection. Click Next>.
5. “Name Your Printer”screen. Unless another
printer of same name is on system or network
you can ignore this step. (You can also make
this Printer the default printer.) Click Next>.
6. “Completing the Add Printer Wizard”window.
Click Finish to complete Installation. Installation
is complete when “Found New Hardware” box
appears in lower right-hand corner of screen.
Step 6
To install Accessories and for Printer set-up or
operation, please refer to “AstroJet 1000P Printer
Operator Manual”, supplied with Printer.
© 2014 Astro Machine Corp 10/30/2014
AJ 1000P Quick Start Guide
630 Lively Blvd.
Elk Grove Village, IL 60007
Phone: (847) 364-6363
Fax: (847) 364 9898
www.astromachine.com
Autres manuels AstroJet Imprimante
AstroJet
AstroJet IB-9000-6P Manuel utilisateur
AstroJet
AstroJet 140 Manuel utilisateur
AstroJet
AstroJet AJ-140 Manuel utilisateur
AstroJet
AstroJet AJ-180 Manuel utilisateur
AstroJet
AstroJet 5000 Manuel utilisateur
AstroJet
AstroJet 300P Manuel utilisateur
AstroJet
AstroJet 2650P Manuel utilisateur
AstroJet
AstroJet M1 Manuel utilisateur
AstroJet
AstroJet 3600P? 3800P Manuel utilisateur
AstroJet
AstroJet M1DX Manuel
