Assa Abloy INTERLOCK P84166 Manuel utilisateur

TWIN BOLT LOCK 18MM THROW -

BI-FOLD DOORS

ASSA ABLOY New Zealand Limited, 6 Armstrong Road, Albany,

North Shore City 0632, New Zealand, Tel 09 415 8031, Fax 0800 478 297 2-02/08NZ

Page 1 of 3

Part #: 077226

INSTALLATION INSTRUCTIONS FOR P84167, P84500, PB3030027,

P84166 AND PB3042227 WITH UNO AND ARIA BI-FOLD HANDLES

Twin Bolt Lock Overall Dimensions:

Figure 1. Twin Bolt Lock Dimensions

Figure 2. Face Routing

Routing Details:

Detail not required for

Non Locking configuration

58.1 (Low Profile Aria and Uno)

Ø16

Ø10

Ø3.3

Threaded shoot bolts shown fully extended

199.7

21.5

273

190

M5 holes for possible side fixing to extrusion

32 (max unthrown)

24 (max thrown)

17.75 (max)

TWIN BOLT LOCK 18MM THROW -

BI-FOLD DOORS

ASSA ABLOY New Zealand Limited, 6 Armstrong Road, Albany,

North Shore City 0632, New Zealand, Tel 09 415 8031, Fax 0800 478 297 2-02/08NZ

Page 2 of 3

Part #: 077226

INSTALLATION INSTRUCTIONS FOR P84167, P84500, PB3030027,

P84166 AND PB3042227 WITH UNO AND ARIA BI-FOLD HANDLES

1. Cut the rods to length allowing for a lock throw of 18mm.

Note: Allowance must also be made for the clearance between

the door and frame, the D-tip length of 44mm and the multi

point rod threaded 14mm into the lock.

2. Press the D-tips onto the end of the multi point rod. Crimp

the rods onto the D-tip to ensure a solid fit (a crimping tool

– P84042 – is available for this task).

3. Screw the rods to the lock, tightening the lock nuts against the

throw bolts (see fig 4). Locking nuts only need to be used when

D-tips are retained by a round rod guide (i.e not needed with

D-shaped guide) to prevent the rod from unwinding.

4. Select the packers to be used and clip this onto the lock body.

Note: The remaining packer can be clipped onto the back of the

lock to hold it for easier fixing in the section.

5. Mount the lock assembly onto the door stile checking lock

function, D-tip protrusion and D-tip orientation. Fix the handle

and lock assembly to the extrusion using the M5 fixing screws.

Note: The 8mm square drive bar should protrude through the

entire lock for adequate performance.

6. For Locking Version: Screw the CYL4 lock housing onto the

lock body using the M4 fixing screw (see Fig 6 for the packer

selection guide). Assemble the lock barrel and housing cover

using the retainer wafer of the lock to hold the assembly

together.

Important Note: The cylinder should not be used externally.

7. Screw the lock escutcheon in place.

Note on Rods: The vertical locking rods supplied cater for a

maximum door height of 2300mm. For taller applications

a multi-point extension kit is available which caters for a

maximum door height of 3300mm, the part number for the

multi-point kit is P84017, one kit required per twin bolt lock

body.

Warning: When tightening lock nut use a spanner to support

the lock bolt. This will prevent any damage to the lock.

See Fig 4.

Fig 4. Rod Assembly with Lock Nut

Assembly Details:

For assembly through the end of the extrusion:

Short bolt

Lock nut

Multi Point rod

Twin bolt lock

Spanners

D-Tip Stainless Steel

(2 of)

Multi-point Rod

(Cut to Correct Length)

Twin Bolt Lock

Lock Nut

(2 of, if required)

Packer

Cyl4 Lock & Components

Low Profile

Uno Escutcheon

Low Profile

Aria Escutcheon

M4 CSK TT Escutcheon

fixing screws

M5 CSK TT Handle

fixing screws

Uno Bi-fold Handle

Aria Bi-fold Handle

M4 CSK TT Cylinder

fixing screws

Fig 3. Lock Assembly

TWIN BOLT LOCK 18MM THROW -

BI-FOLD DOORS

ASSA ABLOY New Zealand Limited, 6 Armstrong Road, Albany,

North Shore City 0632, New Zealand, Tel 09 415 8031, Fax 0800 478 297 2-02/08NZ

Page 3 of 3

Part #: 077226

INSTALLATION INSTRUCTIONS FOR P84167, P84500, PB3030027,

P84166 AND PB3042227 WITH UNO AND ARIA BI-FOLD HANDLES

The length of the M5 fixing screws is critical to the performance of

the lock.

If the screw is too short the lock will not be held correctly.

If the screw is too long the lock may bind and not operate.

Screw Length = E + X + P + (4.5 ± 0.5) mm – refer opposite

Fig 7. Packing system for locking cylinder

In the situation where the lock is assembled into composite (wood and

aluminium) sections, the locking cylinder assembly may require packing to

ensure it sits proud of the door, see Fig 7.

Screw Length Formula:

Sections Non Locking - Use: Locking with Low Profile Lock Escutcheon - Use:

Aluminium

• 38mm internal extrusion width

• 1.6mm extrusion thickness

• M5 x 17mm Screws

• 6.25mm Packer (interior side)

• 6.25mm x 2 Packer (exterior side)

• M5 x 26mm Screws

• M4 x 10mm Screw

• 14.8mm Packer (interior side)

• 5mm Packer (exterior side)

Aluminium

• 38mm internal extrusion width

• 3.6mm extrusion thickness

• M5 x 26 Screws

• 14.8mm Packer (interior side)

• 5mm Packer (exterior side)

• M5 x 26mm Screws

• M4 x 10mm Screw

• 14.8mm Packer (interior side)

• 5mm Packer (exterior side)

This guide shows the M5 screws required for fixing the lock and the M4 screws for fixing the locking cylinder (if locking version), and the

packers that should be used in each situation. For all other section configurations use the formula above.

Screw and Packer Selection Guide:

Cylinder Packing:

Fig 5. Top view of Components in Folding Panel Section

Twin Bolt Lock

Packed Cyl Adapter

Cyl Packer

Cyl Housing

Cyl Housing Cover

M4 CSK Taptite Fixing Screw

Lock Cylinder

Packer (Thickness P)

Extrusion (Thickness X)

Handle Escutcheon

(Thickness E)

Fig 6. Screw Length Formula

Ce manuel convient aux modèles suivants

Autres manuels Assa Abloy Verrouillage

Assa Abloy

Assa Abloy Yale Smart Latch Manuel utilisateur

Assa Abloy

Assa Abloy Sargent SE LP10 Manuel utilisateur

Assa Abloy

Assa Abloy Yale 5300 Series Manuel utilisateur

Assa Abloy

Assa Abloy Sargent KP Series Manuel d'installation

Assa Abloy

Assa Abloy Yale Real Living B1L Z-Wave Caractéristiques techniques

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 MP9800 Series Manuel utilisateur

Assa Abloy

Assa Abloy Yale Easy Manuel utilisateur

Assa Abloy

Assa Abloy HES K20 Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin UT5200 Series Guide de démarrage rapide

Assa Abloy

Assa Abloy OneSystem Espagnolette Manuel utilisateur

Assa Abloy

Assa Abloy Medeco XT Manuel utilisateur

Assa Abloy

Assa Abloy Yale Real Living Assure Lock SL Series Caractéristiques techniques

Assa Abloy

Assa Abloy OneSystem 819N Guide d'installation

Assa Abloy

Assa Abloy Corbin Russwin FE6700 Series Manuel utilisateur

Assa Abloy

Assa Abloy IKON eCLIQ N111 BA3 Manuel utilisateur

Assa Abloy

Assa Abloy Yale P117 Manuel utilisateur

Assa Abloy

Assa Abloy IKON VERSO CLIQ V551 Manuel utilisateur

Assa Abloy

Assa Abloy Securitron Vista V2M1200 Series Manuel utilisateur

Assa Abloy

Assa Abloy Yale Real Living Assure Lock SL YRD256 Caractéristiques techniques

Assa Abloy

Assa Abloy HES 8500 Series Manuel utilisateur

Assa Abloy

Assa Abloy Yale Doorman Manuel utilisateur

Assa Abloy

Assa Abloy hes 8000 Series Manuel utilisateur

Assa Abloy

Assa Abloy 840C-50 Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT FM7300 Series Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur