Assa Abloy Sargent 855 Instructions de montage

Installation and Wiring Instructions

855 Signal Switch Kit

with ElectroLynx®Connector System

A7110D 04/19

Sargent Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

Mounting

Insert

Loosen

#6-32 Flat Head Screws

(DO NOT REMOVE)

Connecting

Arm

855 Switch

Assembly

Connecting

Arm Bracket

Switch

Leaf

The 855 Signal Switch Kit is designed to be

retroﬁt into an existing 80 Series rail assembly.

The signal switch monitors the touch bar and

signals a remote location that someone has

egressed. The 855 signal switch can also be

used as a request to exit switch, to de-energize

a mortise lock.

A. Preliminary Preparation:

1. Provide a 1/4" diameter minimum

raceway in the door to allow insertion of

electrical wires running between signal

switch and electric hinge.

2. Wiring instructions - see wiring diagram

for necessary information.

B. Installation Procedure:

1. Remove end cap by taking out two (2)

screws securing it.

2. Remove mounting plate by taking out

two (2) screws securing it.

3. Remove two (2) #8-32 truss head screws

holding rail to chassis.

4. Remove rail from door.

5. Slide mounting insert out of rail.

6. Loosen two (2) #6-32 ﬂat head screws

on back of rail (closer to hinge).

7. Lift connecting arm bracket and slip

855 switch assembly under bracket, as

shown.

8. Install switch leaf under tail of connecting

arm. Important: Switch leaf may break if

installed on top.

9. Ensure connecting arm bracket is sitting

ﬂush against rail mount.

10.Tighten #6-32 screws.

11. Slide mounting insert back into rail.

12. Install rail onto chassis and tighten #8-32

truss head screws.

13. Reinstall mounting plate and end cap

with appropriate screws.

C. Installation Notes:

1. Door without ElectroLynx connector

system: Cut 8-pin connector off signal

switch wires and hardware to electric

hinge as required.

2. Wiring to pigtail harness or electric hinge

is per facility wiring requirement.

WARNING

his product can expose you to lead

which is known to the state of Califor

nia

to cause cancer and birth defects or other

eproductive harm. For more information go

to www.P65warnings.ca.gov.

Steps B1 and B2

Step B3

Steps B5 and B6

Steps B7 and B8

A7110D 04/19

Sargent Manufacturing Company is prohibited.

Patent pending and/or patent: www.assaabloydss.com/patents

SARGENT Manufacturing Company

100 Sargent Drive

New Haven, CT 06511 USA

800-727-5477

www.sargentlock.com

D. Door with ElectroLynx connector system:

The only wiring required is to the loose wires

on the pigtail harness assembly on the frame

side of the electric hinge.

IMPORTANT:

The plug and receptacle connectors are

designed to mate and lock together as shown

in the ﬁgure. Plug the connectors into each

other with the locking mechanism aligned as

indicated.

DO NOT FORCE CONNECTORS ON ANY

OTHER WAY.

E. Signal Switch (55-) Wiring:

55-

Switch

Connections:

Notes:

1. Switch contract rating: 2A @ 30VDC.

2. Wires must be protected from abrasion.

3. For use with class II circuits only.

4. Wiring diagram indicates push bar extended.

5. ElectroLynx doors - the 855 signal switch, raceway

harness, electric hinge and pigtail connector

terminations and wire colors all match.

Electric hinge

with 8-pin

connectors.

Pigtail harness

with 8-pin

connector.

Yellow (NC), 8

Brown (NO), 7

Blue (C), 6

Raceway harness with

8 and 4-pin connectors.

The 4-pin connectors

are not used.

855 Kit

(Insert with 55-

signal switch and

8-pin connector).

Note: Typical raceway location is

shown. Other locations may exist

depending on door type.

Autres manuels Assa Abloy Système d'ouverture de porte

Assa Abloy

Assa Abloy Norton PR1601BF Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 281 Series Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 1331 Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Manuel utilisateur

Assa Abloy

Assa Abloy h.e.s. 9100 Series Manuel

Assa Abloy

Assa Abloy DC340DA Manuel utilisateur

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Manuel utilisateur

Assa Abloy

Assa Abloy Norton 5700P Series Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 281 Series Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 3828 Series Manuel utilisateur

Assa Abloy

Assa Abloy Norton 6300 Series Manuel utilisateur

Assa Abloy

Assa Abloy Norton 1600H Series Manuel utilisateur

Assa Abloy

Assa Abloy RD150-3 Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT FM8700 Manuel utilisateur

Assa Abloy

Assa Abloy Norton 9510 Series Manuel utilisateur

Assa Abloy

Assa Abloy CMD Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Manuel utilisateur

Assa Abloy

Assa Abloy RIXSON W91DCP Manuel utilisateur

Assa Abloy

Assa Abloy Crawford MCS-R Manuel utilisateur

Assa Abloy

Assa Abloy Adams Rite EX89 Mode d'emploi

Assa Abloy

Assa Abloy Norton SafeZone 7100SZ Series Guide rapide

Assa Abloy

Assa Abloy Yale 6000 Series Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 1130-HU Series Manuel utilisateur

Assa Abloy

Assa Abloy Norton Narrow Profile Series Manuel utilisateur

Manuels Système d'ouverture de porte populaires d'autres marques

Pamex

Pamex KT-INP35 Manuel utilisateur

Label

Label NEPTIS/LE Manuel utilisateur

Cal-Royal

Cal-Royal N-F77CVR Manuel utilisateur

Scrigno

Scrigno OPEN1000 Manuel utilisateur

TriMark

TriMark UM 34 Manuel utilisateur

BFT

BFT WIND RMB 130B 200 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Besam

Besam Swingmaster MP Mode d’emploi

CRL

CRL SENIOR PRIMA Manuel utilisateur

GAL

GAL MOVFR Fiche technique

Olide

Olide 120B Manuel utilisateur

Normstahl

Normstahl IDO7 Manuel utilisateur

Häfele

Häfele Finetta T 70 VF Manuel utilisateur

AGS

AGS D-PL Manuel

Stanley

Stanley MA900ñ Instructions d'installation

WITTUR

WITTUR Hydra Plus UD300 Manuel

Alutech

Alutech TR-3019-230E-ICU Instructions d'installation et d'utilisation

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Fiche technique