Assa Abloy Corbin Russwin DC3210 Series Manuel utilisateur

80-9330-3003-152 04/18

Installation Instructions

permission of Corbin Russwin, Inc. is prohibited.

DC3210 Series

Important

• An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury; and will void

product warranty.

• To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.

• Door closers must be securely fastened to a properly reinforced door and frame with fasteners provided.

• Door closers with a HOLD OPEN ARM are not permitted to be installed in ﬁre door assemblies.

• Door and frame must be speciﬁcally templated for 85°, 90°, 95°, 100°, 105° orb 110° door swing.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

A11 or A12 Heavy Duty Spring Stop Parallel Arm

80-9330-3003-152 04/18

DC3210 Series Closer

Installation Instructions

A11 or A12 Heavy Duty Spring Stop Parallel Arm

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

TO DETERMINE

HAND OF

YOUR DOOR:

LEFT

HAND

DOOR

RIGHT

HAND

DOOR

RHR LHR

A11-Non-Hold Open Arm

STANDARD APPLICATION

WITH 615F58 BRACKET

DEEP REVEAL APPLICATION WITH

M103 OPTION(615F59 CLAMP KIT)

FLUSH PARTITION APPLICATION

WITH

M104 OPTION (615F60 BRACKET)

A12 - Hold Open Arm

1 Introduction

3/8

(10)

1/4-20 THREAD

Drill thru 9/32 (7.1) Enlarge to

3/8

(9.5) Dia. This Side Only

(4 Places)

DOOR

THICKNESS

SEX NUT

LENGTH “L”

1-3/8" (35mm)

1--3/4" (44mm)

&OVER

1-9/32" (33mm)

1-21/32" (42mm)

MOUNTINGSCREW SPECIFICATIONS

ARM AND CLOSER BRACKET

}

or{Option M54:

Sex nuts, furnished

when ordered

1/4-20 oval head machine

screw or 1/4-14 self-drilling

screw Type BSD. 3/16 (4.8)

diameter pilot hole required

forWood Applications.

3/8

(10)

1/4-20 THREAD

Drill thru 9/32 (7.1) Enlarge to

3/8 (9.5) Dia. This Side Only

(4 Places)

DOOR

THICKNESS

SEX NUT

LENGTH “L”

1-3/8" (35mm)

1--3/4" (44mm)

&OVER

1-9/32" (33mm)

1-21/32" (42mm)

MOUNTINGSCREW SPECIFICATIONS

ARM AND CLOSER BRACKET

}

or{Option M54:

Sex nuts,

furnished

when ordered

1/4-20 oval head machine

screw or 1/4-14 self-drilling

screw Type BSD. 3/16 (4.8)

diameter pilot hole required

forWood Applications.

Figure 1

80-9330-3003-152 04/18

DC3210 Series Closer

A11 or A12 Heavy Duty Spring Stop Parallel Arm

Installation Instructions

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

1 Introduction

**NOTE: These forces are for standard templating with bearing type hinges and do not account

for pressure differentials and draft.

*Dimension “C” is only used for Flush Partition application (Frame Template 1C)

Opening

Doors 28" to 32"

615F52 NHO Arm (A11)

615F51 HO Arm (A12)

Doors 33" to 41"

615F54 NHO Arm (A11)

615F53 HO Arm (A12)

Doors 42" to 48"

615F56 NHO Arm (A11)

615F55 HO Arm (A12)

HOLD

OPEN

DEAD

STOP DIM. A DIM. B *DIM. C DIM. A DIM. B *DIM. C DIM. A DIM. A *DIM. C

85° 90° 11

(279)

(254)

10-1/8

(257)

13-1/8

(333)

12-1/4

(311)

12-3/8

(314)

15-1/8

(384)

14-3/8

(365)

14-1/2

(368)

90° 95° 10-1/2

(267)

9-1/2

(241)

9-5/8

(244)

12-5/8

(321)

11-5/8

(295)

11-3/4

(298)

14-1/2

(368)

13-3/4

(349)

13-7/8

(352)

95° 100° 10

(254)

(229)

9-1/8

(232)

(305)

11-1/8

(283)

11-1/4

(286)

13-7/8

(352)

13-1/8

(333)

13-1/4

(337)

100° 105° 9-1/2

(241)

8-1/2

(216)

8-5/8

(219)

11-5/8

(295)

10-5/8

(270)

10-3/4

(273)

13-1/4

(337)

12-1/2

(318)

12-5/8

(321)

105° 110° 9

(229)

(203)

8-1/8

(206)

(279)

10-1/8

(257)

10-1/4

(260)

12-3/4

(324)

12-1/8

(308)

12-1/4

(311)

110° 115° 8-1/2

(216)

7-1/2

(191)

7-5/8

(194)

10-1/2

(267)

9-1/2

(241)

9-5/8

(244)

12-1/4

(311)

11-1/2

(292)

11-5/8

(295)

Size of Door & Door Closer

Type of

Installation Interior Exterior

In-swinging

Exterior

Out-swinging

Recommended

Closer Size

**Max. Opening Force

lbs/f

Parallel Arm

2' 4" - - 1 8

2' 6" - - 2 14

3' 0" - 2' 6" 3 16

3' 6" - 3' 0" 4 22

4' 0" - 3' 6" 5 24

4' 6" - 4' 0" 6 26

SEE CHART TO SELECT DEGREE OF DOOR OPENING AND DOOR WIDTH FOR YOUR DOOR.

THEN, DETERMINE FRAME CONDITION: STANDARD & DEEP REVEAL (use Dim’s. A & B) or FLUSH

PARTITION (use Dim’s A & C)

80-9330-3003-152 04/18

DC3210 Series Closer

Installation Instructions

A11 or A12 Heavy Duty Spring Stop Parallel Arm

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Installation

1. Template

Mark door and jamb (for closer bracket and arm

brackets).

Frame Template 1A (Standard Application with

615F58 Bracket) (Figure 2)

For Deep Reveal: Frame Template 1B. (Figure 3)

For Flush Partition: Frame Template 1C. (Figure 4)

1/2

(12.7)

2-3/4

(70)

FRAME STOP

TOPOF DOOR

HINGE

PIVOT

DOOR

FRAME STOP

2-3/4

(70) 3/8

(9.5)

(50.8)

7/16

(11.1)

CLOSER

BRACKET

(25.4) 4-5/16

(109.5)

TYP.

1-3/8

(35)

1-1/4

(31.8)

1-1/8

(29)

3/4

(19)

REVEAL 615F58

BRACKET

615F58

BRACKET

Frame Reveals 1-7/8 to 4-5/8

(48mm to 117mm)

Reveal

Door

615F58

BRACKET

Door Preparation is Typical for

all Frame Templates

1A, 1B, and 1C

NOTES:

• Check hand of door. (Figure 1)

• Right Hand Application Shown, Left Hand

Opposite

• Dimensions given in inches (mm).

Do Not Scale Drawing.

• Closer must be installed in a true

horizontal plane to ensure proper closer

performance.

Figure 2

80-9330-3003-152 04/18

DC3210 Series Closer

A11 or A12 Heavy Duty Spring Stop Parallel Arm

Installation Instructions

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Installation

2. Install Closer Bracket. (Figure 5)

1/2

(12.7)

HINGE

PIVOT

DOOR

FRAME STOP

2-3/4

(70)

3/8

(9.5)

(50.8)

7/16

(11.1)

TYP.

1-3/8

(35)

REVEAL

5/16

(8)

2-1/8

(54)

4-3/8

(69.9)

615F59

CLAMP (TYP)

Door

Clamps with Spacer

Clamps Only

SPACER

FRAME TEMPLATE 1B DEEP REVEAL APPLICATION with M103 OPTION (615F59 CLAMP KIT)

FRAME TEMPLATE 1C FLUSH PARTITION APPLICATION with M104 OPTION (615F60 BRACKET)

1-1/2

(38.1)

1/2

(12.7)

2-1/2

(63.5)

1-3/4

(44)

3/4

(19.1) CFrame Reveals 0to 1/8 (0mm to 3mm)

Reveal

Frame Reveals Over 4-5/8 (117mm)

DoorFrame

Reveal

CLAMP

FRAME

CLAMP

615F60

BRACKET

Pin Hole End

Countersunk Holes

Figure 3

Figure 4

Figure 5

80-9330-3003-152 04/18

DC3210 Series Closer

Installation Instructions

A11 or A12 Heavy Duty Spring Stop Parallel Arm

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Installation

3. Mount Closer Body to Closer Bracket.

(Figure 6)

4. Fasten Arm Brackets to Frame

For Frame Templates “1A” and “1B” fasten

main arm bracket to frame. Locate and install

reinforced brackets 615F58 (1A) or 615F59

Kit (1B).

For Frame Template “1C” fasten Flush

Partition Bracket 615F60 to frame face

and install main arm bracket to the 615F60

Bracket.

5. Connect Arm To Closer (Figure 7)

Using hex wrench provided, close (turn

clockwise) CLOSING SPEED VALVE. (Figure

9) DO NOT OVER TIGHTEN.

• Open door to approximately 60°

• Using wrench on underside of spindle,

rotate spindle approximately 135° toward

hinge edge of door.

• Install arm on spindle at an approximate 90°

angle to door.

• Reopen CLOSING SPEED VALVE.

• Install and tighten arm washer and screw.

Holding Pins

1/4-20 x 1/2 OHMS (2)

DOOR

SPINDLE

ARM

CENTERLINE

ALL ANGLES SHOWN ARE APPROXIMATE

DOOR

90°

SPINDLE

ROTATED 135°

Rotate 135°

SPINDLE AT REST

60°

DOOR

135°

WRENCH

90°

ARM

Figure 6

Figure 7

80-9330-3003-152 04/18

DC3210 Series Closer

A11 or A12 Heavy Duty Spring Stop Parallel Arm

Installation Instructions

permission of Corbin Russwin, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Adjustments

Adjustments (Figure 8)

(3/32 Allen Wrench Provided)

Closing Speed Valve (Figure 9)

To adjust speed of door closing from fully

open to a position 2 to 5" from closed, turn

Closing Speed Valve CLOCKWISE to SLOW

closing, COUNTER-CLOCKWISE to SPEED

closing.

Latching Speed Valve (Figure 10)

After closing speed has been obtained, turn

latching speed valve CLOCKWISE to SLOW

latching or COUNTER-CLOCKWISE to SPEED

latching for last 2 to 5 of door travel.

NOTE: Set combination of CLOSING and

LATCHING speeds to between 3 and 7

seconds Use of door by handicapped,

elderly or small children, may require

even greater closing time.

Backcheck Intensity Valve (Figure 9)

Turn valve COUNTER- CLOCKWISE to reduce

backcheck or CLOCKWISE to increase

backcheck. (Backcheck should be set to give

a soft cushioning action, not a sudden stop).

Delayed Action Valve (Figure 9)

Turn valve CLOCKWISE to SLOW closing,

COUNTERCLOCKWISE to SPEED closing.

Delayed action may be adjusted from 20

seconds to 90 seconds, depending on degree

of door swing. Delay occurs at the beginning

of the door closing cycle from fully open down

to 70°, where the closing speed valve then

begins its control.

Delayed Action

Option

M-71

Backcheck

Latch

Sweep

LATCHING

SPEED

VA LV E

Power

Size

Stamp

Date Stamp

BACKCHECK

INTENSITY VALVE

OPTION M71

DELAYED

ACTION VALVE

CLOSING

SPEED VALVE

SPRING POWER ADJUSTER

(5/16" WRENCH or SOCKET)

(FLAT TIP SCREWDRIVER)

Rotate

To Decrease

Hold Open

Force

Increase

Hold Open

Force

Hold Open

“On” Hold Open Force

HOLD OPEN ADJUSTMENTS - A12 ARMSONLY

Hold Open

“Off”

Figure 8

Figure 9

Figure 10

Figure 11

80-9330-3003-152 04/18

permission of Corbin Russwin, Inc. is prohibited.

Patent pending and/or patent: www.assaabloydss.com/patents

Corbin Russwin

225 Episcopal Road

Berlin, CT 06037

Phone: 800-543-3658

Fax: 800-447-6714

corbinrusswin.com

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Adjustments

Adjust Spring Power According to Chart

DC3200 Size 1-6 Adjustment (Figure 12)

• All DC3200 closers are factory set at an

approximate Size 3.

Full Cover(Standard)

Slim Cover (Option M76)

Figure 12

Figure 13

Size of Door No. of Full (360°)

Turns Clockwise of

Power Adjuster

Equivalent Closer

Size (Approx.)

Interior Exterior

In-Swinging

Exterior

Out-Swinging

2' 4"

(712)

2' 6"

(764) - 4 2

2' 6"

(764)

3' 0"

(915) - 8 3

3' 0"

(915)

3' 6"

(1067)

2' 6"

(764) 12 4

3' 6"

(1067)

4' 0"

(1219)

3' 0"

(915) 16 4

Figure 14

4 Cover Installation

Full Cover(Standard)

Slim Cover (Option M76)

Install Cover (Figure 13)

Slip cover over closer. Hold tightly against

closer mounting surface. Secure on each

side with 6-32 x 1/4 PBHMS screws.

Slim Cover Option M76 only (Figure 14)

Position spindle cap over unused spindle

and secure with truss head screw.

• Adjust closer as necessary for door size

using this chart.

• Readjustment may be required to suit

prevailing conditions.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Assa Abloy Système d'ouverture de porte

Assa Abloy

Assa Abloy SARGENT FM8700 Manuel utilisateur

Assa Abloy

Assa Abloy Pando Mini Go Manuel utilisateur

Assa Abloy

Assa Abloy Norton 6011 Series Manuel utilisateur

Assa Abloy

Assa Abloy DC200 Manuel utilisateur

Assa Abloy

Assa Abloy Norton 7540STH Series Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin PED159 Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin ED8200A Series Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Manuel utilisateur

Assa Abloy

Assa Abloy Norton 5700P Series Manuel utilisateur

Assa Abloy

Assa Abloy DC140 Manuel utilisateur

Assa Abloy

Assa Abloy Norton 6300 Pull Side Series Guide rapide

Assa Abloy

Assa Abloy NORTON RIXSON 1600 Series Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Manuel utilisateur

Assa Abloy

Assa Abloy Adams Rite EX89 Mode d'emploi

Assa Abloy

Assa Abloy King 70 Series Manuel utilisateur

Assa Abloy

Assa Abloy Norton 7900H-B Series Manuel utilisateur

Assa Abloy

Assa Abloy Besam SL500 Manuel utilisateur

Assa Abloy

Assa Abloy MAB 609 + AC572 Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 281 Series Manuel utilisateur

Assa Abloy

Assa Abloy Besam SP33-M Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 268 Series Manuel utilisateur

Assa Abloy

Assa Abloy Crawford MCS-R Manuel utilisateur

Assa Abloy

Assa Abloy RIXSON W91DCP Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin PED4200 Series Manuel utilisateur

Manuels Système d'ouverture de porte populaires d'autres marques

Pamex

Pamex KT-INP35 Manuel utilisateur

Label

Label NEPTIS/LE Manuel utilisateur

Cal-Royal

Cal-Royal N-F77CVR Manuel utilisateur

Scrigno

Scrigno OPEN1000 Manuel utilisateur

TriMark

TriMark UM 34 Manuel utilisateur

BFT

BFT WIND RMB 130B 200 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Besam

Besam Swingmaster MP Mode d’emploi

CRL

CRL SENIOR PRIMA Manuel utilisateur

GAL

GAL MOVFR Fiche technique

Olide

Olide 120B Manuel utilisateur

Normstahl

Normstahl IDO7 Manuel utilisateur

Häfele

Häfele Finetta T 70 VF Manuel utilisateur

AGS

AGS D-PL Manuel

Stanley

Stanley MA900ñ Instructions d'installation

WITTUR

WITTUR Hydra Plus UD300 Manuel

Alutech

Alutech TR-3019-230E-ICU Instructions d'installation et d'utilisation

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Fiche technique