Assa Abloy SARGENT BL7300 Series Manuel utilisateur

A8220D 10/19

Installation Instructions

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

Important

The latches, rods, and cassette are pre-installed.

This product must be installed by a factory trained technician.

Multi-Point Lock

FM7300 Series and BL7300 Series

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

TOC Table of Contents

1 Package Contents ...............................................................4

2 Tools Required ..................................................................5

a Tools Required for Electronic Access Control (EAC) Shield ........................5

b Tools Required for Dogging Indicator Option.....................................5

3 Installation ......................................................................6

a Check Door......................................................................6

b Door Installation ................................................................6

c Install Top Strike into Door Frame................................................6

d Install Center Strike into Door Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

e Remove Retractor Inserts........................................................7

f Check Latches (uninstalled)......................................................7

g Install Bottom Strike.............................................................8

h Top and Bottom Latch Adjustment............................................. 10

i Mortise Lock Install ............................................................ 12

j Final Mortise Lock and Trim Installation ........................................ 13

k Electronic Access Control (EAC) Reader and Controller Installation ............. 13

l Deadbolt Label Installation (FM7300 Only) .................................... 13

m Key Override with Deadbolt Function Operation Check ........................ 13

n Electronic Access Control (EAC) Shield (if applicable)........................... 14

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

4 Optional Installation........................................................... 14

a Dogging Indicator Installation ................................................. 14

5 Addendum .................................................................... 17

a Check Door.................................................................... 17

b Place Door Horizontal on Sawhorse............................................ 17

c Install Lockbody Cassette (LBC) ................................................ 18

d Latch Rod Guides .............................................................. 18

e Feed Top Rod into Door........................................................ 19

f Align with Lockbody Cassette (LBC) ............................................ 19

g Troubleshoot Latch Installation ................................................ 20

h Correct Rod Installation Check................................................. 20

i Secure Top Latch .............................................................. 21

j Tighten Set Screw ............................................................. 21

k Bottom Latch Installation...................................................... 22

l Check Latch ................................................................... 22

m Mortise Reinforcer and Mortise Lock Installation ............................... 23

n Final Installation............................................................... 23

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

1 Package Contents

Part Number Description

1 82-5342 Multipoint cassette

2 82-5345 Trim mounting screw pack

3 82-5346 Top/bottom case mounting screw pack

4 82-5347 Top strike pack

5 82-5348 Bottom strike pack

6 82-5349 Mortise mounting/reinforcement pack

7 82-5350 Center strike pack

82-5351 IN/PN Inside cover shield pack

82-5352 Harmony inside cover shield pack

82-5353 Passport inside cover shield pack

9 188 Dogging indicator (includes item 13) (specify finish)

10 82-5383 Screw retainer pack

11 82-5386 Top case and rod assembly (specify door size)

12 82-5387 Bottom case and rod assembly (specify door size)

13 82-5400 Dogging indicator screw pack (specify finish)

14 01-4597 T-wrench, adjustment

15 Consult factory Outside armor front

16 Consult factory Mortise lock

17 Consult factory Mortise trim

18 Consult factory Cylinder

Note:

The grayed parts are preinstalled by the

door manufacturer and relate to the

Addendum section beginning on page 16.

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2 Tools Required

Tape measure Hammer Flashlight 1/8" Allen

(supplied)

3/32" Allen

(supplied)

5/32" Allen

Drill 1/8" Masonry

drill bit

#3 Phillips

bit

Slotted

screwdriver

#1, #2, #3

Phillips head

screwdrivers

Chisel 3/8"

Anchor set

a Tools Required for Electronic Access Control (EAC) Shield

#29 Drill bit

(.136")

#8-32 Tap

b Tools Required for Dogging Indicator Option

#7 Drill bit

(.201")

82° Countersink

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation

a Check Door

Verify the door is:

• Correct size and hand for opening.

• Correctly prepared to Template 4740.

IMPORTANT

If measurement is incorrect, DO NOT PROCEED

WITH INSTALLATION. Contact door manufacturer.

(Figure1)

b Door Installation

Hang the door on the frame.

IMPORTANT

If the door rubs along the floor, do not complete

this installation! Contact door manufacturer.

c Install Top Strike into Door Frame

• Remove plastic strike filler and discard.

Figure1

Door Height

Door Width

of Lockbody

Outswing Door

Shown

± 5/64"

39-9/16"

(101.4 cm)

Figure2

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation (cont.)

d Install Center Strike into Door Frame

• Install two (2) ¼-20 socket cap flat head screws.

(Figure3)

e Remove Retractor Inserts

WARNING

The door now has the ability to latch.

(Figure4)

f Check Latches (uninstalled)

• Insert the uninstalled outside mortise trim and

rotate to verify the top and bottom latches

retract flush with the door. Do not install

mortise trim at this time. (Figure5)

• Move the top strike back and forth until the top latch engages the strike. (Figure6)

Figure3

Figure4

Figure5

TOP OF DOOR FRAME

Figure6

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation (cont.)

g Install Bottom Strike

• Close the door and mark the location of the bottom bolt.

3/8" MAX

Bottom of door

to floor.

✓

Figure7

• Open the door and place the strike over the bottom bolt location. Mark the location of the bottom

strike pocket and hole locations. (Figure7)

Note:

The strike is not symetric. Install as shown. If needed, the strike can later be rotated to increase bolt

clearance. (Figure8)

Door Swing

Jamb

Narrow

Wide

Bottom Strike Pocket

Figure8

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation (cont.)

g Install Bottom Strike (cont.)

Flush Mount (Figure9)

Mortise the strike into the floor 1/4" deep.

(Optional for 3/8" door to floor gap.)

IMPORTANT

Use a vacuum or compressed air to

clear holes ofdebris. (Figure10)

Cross Sectional View

Flush Mount (Figure11)

Surface Mount (Figure12)

Drill two (2) 3/8"

diameter holes

by 2-1/4" deep.

Chisel the bottom strike pocket

1" deep to ensure the bolt has

full projection.

Figure12

IMPORTANT

Use a vacuum or compressed air to

clear holes ofdebris. (Figure13)

Cross Sectional View

Surface Mount (Figure14)

2 1/4"

Figure14

Drill two (2) 3/8"

diameter holes

by 2-1/4" deep.

Chisel the bottom strike

pocket 1" deep to ensure

bolt has full projection.

1/4" D EEP

Figure9

Use the anchor tool

to set anchors.

Figure10

2 1/4

Figure11

Use the anchor tool

to set anchors

Figure13

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation (cont.)

h Top and Bottom Latch Adjustment

• With the door hung, measure the clearance

between the top and bottom bolts and strikes.

(Figure15)

Note:

If both measurements equal 1/16" proceed to Step

3i, otherwise proceed with Step 3h as follows:

• Remove the mortise filler cap and discard.

(Figure16)

• Retract the latches by roting the lever and

opening the door. (Figure17)

Figure17

• Using the supplied 1/8" Allen wrench, loosen

the set screw 1/4 turn maximum. This allows

hex rods to rotate during the latch bolt

adjustment. (Figure18)

Figure15

1/16" Bolt to strike clearance.

TOP OF DOOR

1/16" Bolt to strike clearance.

BOTTOM OF DOOR

Figure16

Note location

of set screws.

Figure18

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Assa Abloy Serrure de porte

Assa Abloy

Assa Abloy effeff MAG-600SM Manuel utilisateur

Assa Abloy

Assa Abloy RIXSON 93 Manuel utilisateur

Assa Abloy

Assa Abloy ZI IKON eCLIQ N109 Manuel utilisateur

Assa Abloy

Assa Abloy Yale Doorman Guide de dépannage

Assa Abloy

Assa Abloy effeff 118 Series Manuel utilisateur

Assa Abloy

Assa Abloy KESO KEK i-turn Manuel de l'opérateur

Assa Abloy

Assa Abloy Lockwood CAVITY LOCK Manuel utilisateur

Assa Abloy

Assa Abloy eCLIQ Manuel utilisateur

Assa Abloy

Assa Abloy Sargent FM-PE8700 Series Manuel utilisateur

Assa Abloy

Assa Abloy CYE321 Manuel utilisateur

Assa Abloy

Assa Abloy IP2326N Mode d'emploi

Assa Abloy

Assa Abloy CLIQ Manuel utilisateur

Assa Abloy

Assa Abloy EL460 Manuel utilisateur

Assa Abloy

Assa Abloy RIXSON W73 Manuel utilisateur

Assa Abloy

Assa Abloy ePED 1386-00 Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin Access 800 9800 TCWI1 Series Manuel utilisateur

Assa Abloy

Assa Abloy OneSystem type A Mode d’emploi

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 9600 Series Manuel utilisateur

Assa Abloy

Assa Abloy ML22HPH Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Manuel utilisateur

Assa Abloy

Assa Abloy Yale Real Living YRDZW Caractéristiques techniques

Assa Abloy

Assa Abloy Effeff 843G Manuel utilisateur

Assa Abloy

Assa Abloy ABLOY EL654 Manuel utilisateur

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD226 Caractéristiques techniques

Manuels Serrure de porte populaires d'autres marques

We.lock

We.lock SECBNEBL51 Manuel utilisateur

Iseo

Iseo MA1A Manuel utilisateur

ID Lock

ID Lock 150 Manuel utilisateur

Lockly

Lockly ACCESS TOUCH PRO Manuel utilisateur

iLoq

iLoq G50S Manuel utilisateur

SDC

SDC Z7835 Manuel utilisateur

ilco

ilco 452 Manuel utilisateur

Samsung

Samsung shs-h705 Manuel utilisateur

TRU-BOLT

TRU-BOLT 08102017 Manuel utilisateur

CDVI

CDVI 500-LADJ Manuel utilisateur

Igloohome

Igloohome Deadbolt 2S Metal Grey Instructions d'installation et d'entretien

eSSL

eSSL FL-300 Manuel utilisateur

JAKO

JAKO JKBTNX4 Manuel utilisateur

Dorma

Dorma MUNDUS PREMIUM GK 50 Guide de l'utilisateur

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuel utilisateur

Yale

Yale MORTISE 8800 SERIES Manuel utilisateur

Siegenia

Siegenia KFV AS3500 Manuel utilisateur

Saflok

Saflok Quantum ädesē RFID Manuel utilisateur